1、BRITISH STANDARDBS EN 3733-104:2008Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 104: Receptacle connector dummy four holes fixing Product standardICS 49.060g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50
2、g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 3733-104:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 May 2008 BSI 2008I
3、SBN 978 0 580 60569 7National forewordThis British Standard is the UK implementation of EN 3733-104:2008.The UK participation in its preparation was entrusted to Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology.A list of organizations represented on this committee c
4、an be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since p
5、ublicationDate CommentsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 3733-104 April 2008 ICS 49.060 English Version Aerospace series - Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous - Part 104: Receptacle connector dumm
6、y four holes fixing - Product standard Srie arospatiale - Connecteur optique circulaire monovoie accouplement par bague filete, temprature dutilisation 150 C continu - Partie 104 : Embase de repos, quatre trous de fixation - Norme de produit Luft- und Raumfahrt - Optischer Rundsteckverbinder einpoli
7、g Schraubkupplung, Betriebstemperatur 150 C konstant - Teil 104: Blindsteckdose mit vierlochflansch - Produktnorm This European Standard was approved by CEN on 19 January 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this Eu
8、ropean Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (Eng
9、lish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgari
10、a, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZA
11、TION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3733-104:2008: E2 Contents Page Foreword3 1 Scope 4 2 No
12、rmative references 4 3 Terms and definitions .4 4 Required characteristics.4 5 Designation 6 6 Marking .7 7 Technical specification .7 BS EN 3733-104:20083 Foreword This document (EN 3733-104:2008) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD
13、-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the s
14、tatus of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at the latest by October 2008. Attention is drawn to the possibility that some of the elements of this document may be the
15、subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium
16、, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 3733-104:20084
17、1 Scope This standard specifies the characteristics of receptacle connector dummy four holes fixing for single channel fibre optic plug connectors, operating temperature up to 150 C. Connector interface dimensions, table of tests and qualification approval requirements are contained in the Technical
18、 Specification EN 3733-001. EN 3733-002, List of product standards, includes the listings of product types, codification and applicable combinations of product types. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated reference
19、s, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: General. EN 3733-001, Aerospace series Connector, optical, c
20、ircular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 001: Technical specification. 1)EN 3733-002, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 002: Li
21、st of product standards. EN 3733-003, Aerospace series Connector, optical, circular, single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 003: Plug connector for cable to EN 4532 Product standard. EN 3733-004, Aerospace series Connector, optical, circular,
22、single channel, coupled by self-locking ring, operating temperature up to 150 C continuous Part 004: Receptacle, connector, four hole fixing for cable to EN 4532 Product standard. 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 2591-100 apply. 4 Requi
23、red characteristics 4.1 Dimensions and mass Dimensions (in millimetres) shall be as shown in Figure 1. 1) Published as ASD Prestandard at the date of publication of this standard. BS EN 3733-104:20085 Key 1 Maximum panel thickness rear mounted 3,0 2 Seal 3 Thread 4 Four holes 3,10 0,05 typical Figur
24、e 1 Mass: 13,1 g max. 4.2 Panel cut-out and mounting of connectors Panel cut-out and connector mounting details shall be as shown in Figures 2 and 3 respectively. Dimensions are in millimetres. Key 1 Rear panel mount only 2 Four holes 3,50 0,10 typical 3 Recommended Figure 2 21 3 4 3 1 2 18,30 min.B
25、S EN 3733-104:20086 Key 1 Panel 2 Screw head Figure 3 4.3 Materials Nickel-copper shell, fluorosilicone seal. 4.4 Application combinations This dummy receptacle is for use with Product Standards conforming to EN 3733-003 and incorporates universal keying to enable any plug connector keyway orientati
26、on to be accommodated. See EN 3733-002 for applicable combinations of accessories and connectors. 5 Designation EXAMPLE Description block DUMMY RECEPTACLE, FOUR HOLES Identity block EN3733-104B Number of the basic standard Product standard (see EN 3733-002) Class (see EN 3733-001, test fluids class
27、B) NOTE 1 Part number spacing as shown is for clarity only. NOTE 2 If necessary, the code I9005 may be placed between the description block and the identity block. Front mounting Rear mounting 1 12 2 BS EN 3733-104:20087 6 Marking See EN 3733-001. 7 Technical specification Dummy receptacle connector
28、s are qualified by read-across to the applicable qualification requirements of Product Standard EN 3733-004, receptacle connector four holes fixing. BS EN 3733-104:2008BS EN 3733-104:2008BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national body respon
29、sible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendmen
30、ts or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found
31、on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards pu
32、blications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of thos
33、e that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services
34、are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase pri
35、ce of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about
36、 BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may b
37、e reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and
38、size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.
