1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 840-3:2012Mobile waste and r e c y c l i n g c o n t a i n e r sPart 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb li
2、fting devices Dimensions and designBS EN 840-3:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 840-3:2012. It supersedes BS EN 840-3:2004, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e B / 5
3、0 8 / 1 , W a s t e c o n t a i n e r s a n d a s s o c i a t e d lifting devices on refuse collection vehicles.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. U
4、sers are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012.ISBN 978 0 580 72434 3 ICS 13.030.40 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the author
5、ity of the Standards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 840-3:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 840-3 December 2012 ICS 13.030.40 Supersedes EN 840-3:2004English Version Mobile waste and recycl
6、ing containers - Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices - Dimensions and design Conteneurs roulants ordures mnagres et recyclables - Partie 3 : Conteneurs 4 roues de capacit jusqu 1 300 l couvercle(s) bomb(s), pour lv
7、e-conteneurs par tourillon et/ou peigne - Dimensions et conception Fahrbare Abfall- und Wertstoffbehlter - Teil 3: Behlter mit 4 Rdern und einem Nennvolumen bis 1 300 l mit Schiebedeckel(n), fr Schttungen mit Zapfenaufnahme und/oder fr Kammschttungen - Mae und Formgebung This European Standard was a
8、pproved by CEN on 22 September 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such na
9、tional standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own lan
10、guage and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greec
11、e, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG M
12、anagement Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 840-3:2012: EBS EN 840-3:2012EN 840-3:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definiti
13、ons .44 Volumes 55 Dimensions and design 56 Nominal mass .67 Safety and health requirements .68 Testing 69 Marking .610 Designation 7Annex A (informative) Recommendations for manufacturers of lifting devices . 16Annex B (informative) A-Deviations . 18Bibliography . 19BS EN 840-3:2012EN 840-3:2012 (E
14、) 3 Foreword This document (EN 840-3:2012) has been prepared by Technical Committee CEN/TC 183 “Waste management”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the la
15、test by June 2013, and conflicting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such
16、patent rights. This document supersedes EN 840-3:2004. Technical changes since the latest edition: The content has been adapted to the current state of the art and revised editorially. Figure 3 has been deleted. Frontal receivers Form B and C have been deleted. Figure 2 (now Figure 4) has been chang
17、ed accordingly. This European Standard is one part of the series of standards of EN 840 with the main title Mobile waste and recycling containers comprising the following parts: Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices Dimensions and design; Part 2: Conta
18、iners with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices Dimensions and design; Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices Dimensions and design (the present document);
19、Part 4: Containers with 4 wheels with a capacity up to 1 700 l with flat lid(s), for wide trunnion or BG- and/or wide comb lifting devices Dimensions and design; Part 5: Performance requirements and test methods; Part 6: Safety and health requirements. According to the CEN/CENELEC Internal Regulatio
20、ns, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
21、 Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 840-3:2012EN 840-3:2012 (E) 4 1 Scope This European Standard specifies dimensions and design requirements of mobile waste and re
22、cycling containers with 4 wheels, with dome lid(s) and capacity up to 1 300 l to be used by trunnion and/or comb lifting device. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated refer
23、ences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 840-2:2012, Mobile waste and recycling containers Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or c
24、omb lifting devices Dimensions and design EN 840-5, Mobile waste and recycling containers Part 5: Performance requirements and test methods EN 840-6:2012, Mobile waste and recycling containers Part 6: Safety and health requirements EN 1501-1, Refuse collection vehicles General requirements and safet
25、y requirements Part 1: Rear loaded refuse collection vehicles EN 1501-5:2011, Refuse collection vehicles General requirements and safety requirements Part 5: Lifting devices for refuse collection vehicles EN ISO 11469, Plastics Generic identification and marking of plastics products (ISO 11469) 3 Te
26、rms and definitions For the purposes of this document, the following terms and definitions apply. NOTE Terms for components of mobile waste containers and lifting devices in three languages are given in Annex A of EN 840-1:2012. 3.1 mobile waste container appropriately designed container fitted with
27、 wheels intended to temporarily store waste 3.2 lifting device structure which picks-up, tilts and empties containers 3.3 comb lifting device lifting device in which the picking-up system consists of a row of teeth and a locking system to retain the container during emptying 3.4 trunnion lifting dev
28、ice lifting device in which the picking-up system consists of a pair of arms with automatic locking mechanism to fit the trunnion to retain the container during emptying 3.5 volume total space inside the container when the lid is closed BS EN 840-3:2012EN 840-3:2012 (E) 5 3.6 nominal volume capacity
29、 volume stated by the manufacturer Note 1 to entry: See Table 1 without tolerances. Note 2 to entry: The English term “capacity“ and the French term “capacit“ are translated in the German version by the term “Nennvolumen“. 3.7 nominal mass mass, which is calculated as given in Clause 6 3.8 total per
30、missible mass mass of the container plus the nominal load 3.9 functional and safety dimensions essential dimensions which ensure the functionality and interchangeability of the container with the compatible lifting device and which are necessary for the operators safety and health 4 Volumes This par
31、t of EN 840 identifies the two classes of containers: Class I - small size (nominal volume up to 1 000 l); Class II - large size (nominal volume between 1 000 l and 1 300 l). Within the two above-mentioned classes of containers the following volumes are identified: 770 l, 1 000 l, 1 100 l and 1 300
32、l. Nominal volumes different from those referenced can be used by agreement between user and manufacturer. The tolerance of the volumes shall be 5 % maximum measured according to EN 840-5. 5 Dimensions and design 5.1 The design of the containers need not correspond to the drawings given in Figures 1
33、 to 3. The functional dimensions given in Table 1 shall be respected. Recommendations for manufacturers of lifting devices are given in Annex A (see also EN 1501-1). 5.2 The container shall be constructed so that when it is unloaded or loaded with a nominal load (see Clause 6), it fits on an approve
34、d compatible lifting device. It shall be automatically locked safely into the lifting device during the lifting operation. If the container is equipped with a comb receiver, it shall correspond to Figure 4 and Figure 6. 5.3 The lid(s) shall cover the opening of the container completely. It shall be
35、opened easily by the lifting device during the emptying cycle It/they shall be made with at least two fixing points and have at least one means of opening. 5.4 Handles fitted in front of the trunnion shall have a measurement over the handles of 10 mm less than the actual measurement in Table 1, dime
36、nsion N 33. The handles and their location also shall be designed so that they do not damage the operator. 5.5 If the container has ribs in the frontal receiver they shall meet the requirements of Figure 4 and Figure 6. BS EN 840-3:2012EN 840-3:2012 (E) 6 5.6 The container shall have 4 swivel castor
37、s. Each swivel castor shall be capable of withstanding 1/3 of the total permissible mass. Each castor shall meet the requirements of EN 840-5. The container shall have facilities for mounting the castor platine according to at least one of the measurements as shown in Figure 7. 5.7 All the surfaces
38、of the container including design features shall be smooth and free of any foreign bodies or flaws. 5.8 The container should have a drain plug. 5.9 When direction locks are fitted they shall be fixed on at least two castors. 5.10 The container should be fitted with two braked wheels to requirements
39、of EN 840-5. In case of centralized braking and locking system the brake pedal and the lock shall be fixed on a lateral side of the container. The centralized locking shall be able to be unlocked with a standard triangular key as shown in Figure 8. The effectiveness of this centralized braking syste
40、m shall conform to EN 840-5. 6 Nominal mass The container shall be constructed strongly enough to carry a mass of 0,4 kg/dm x nominal volume. Containers with a nominal volume of more than 1 100 l shall be constructed strongly enough to carry a load of 440 kg. 7 Safety and health requirements The con
41、tainer shall meet the safety and health requirements according to EN 840-6. 8 Testing The container shall fulfil the performance requirements and the tests of EN 840-5. 9 Marking 9.1 Each container complying with the requirements of this part of EN 840 shall be durably and readably marked on the bod
42、y in a visible part with: number of this European Standard (EN 840-3); nominal volume; manufacturers name or trademark; total permissible mass, in kilograms; year and month of manufacturing. 9.2 Additional marking for quality, recycling, etc. is allowed. Starting five years after the publication of
43、this standard, plastic parts of containers, lids and wheels shall be marked in accordance with EN ISO 11469. The use of recycled materials is allowed, presuming that all requirements of this standard are complied with. BS EN 840-3:2012EN 840-3:2012 (E) 7 10 Designation The container complying with t
44、he requirements of this European Standard shall be designated as follows: Container EN 840-3 1 100 A A 440 Description Standard number Nominal volume, in litres A = frontal receiver 0 = without frontal receiver Lateral receiver: A = trunnions 0 = without lateral receiver Nominal load, in kilograms B
45、S EN 840-3:2012EN 840-3:2012 (E) 8 Table 1 Dimensions Dimensions in millimetres Dimension NaClass I - Small sizes 1 000 l Class II - Large sizes 1 000 l Remarks 770 l 1 100 l 1 300 l 1 1 370 10 1 370 10 1 370 10 In case of trunnions 2 820 max. 1 115 max. 1 115 max. 3 1 100 max. 1 245 max. 1 245 max.
46、 4 1 425 max. 1 470 max. 1 480 max. 5860 min.; 1 290 max. 860 min.; 1290 max. Tipping edge 6 - 855 50 855 50 Only design B 7135 min.; 280 max. 135 min.; 280 max. 135 min.; 280 max. 8550 min.; 700 max. 650 min.; 850 max. 650 min.; 850 max. Handle position if required 9 600 to 850 600 to 850 600 to 85
47、0 Lock position if presented 10255 405+1040550+1040550+For design A - 500 15 500 15 For design B 11 200 2*) 200 2*) 200 2*)*) min 160 optional according to 5.3 of EN 840-6:2012 1219 min. 19 min. 19 min. In case of frontal receiver 135+3135+3135+313In case of frontal receiver 142221+2221+2221+In case
48、 of frontal receiver 15 - - - This dimension is no more used 1626 1 26 1 26 1 In case of frontal receiver 17 58 max. 58 max. 58 max. In case of frontal receiver 1820 min. 20 min. 20 min. In case of frontal receiver 19130 max. 130 max. 130 max. When ribs are fitted 20 15 max. 15 max. 15 max. 218133+8
49、133+8133+In case of frontal receiver. For design B 23 40 2 40 2 40 2 In case of trunnions 24300 670+300 670+300 670+The front of the plastic container beneath the ribs of the lifting comb shall be smooth. No constructions shall protrude in this area. 254010350+350 10 350 10 Clearance for lifting device 26 535
