1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 10051:2010Continuously hot-rolled stripand plate/sheet cut fromwide strip of non-alloy andalloy steels Tolerances ondimensions and shapeBS EN 10051:2010 BRITISH STANDARDNat
2、ional forewordThis British Standard is the UK implementation of EN 10051:2010. Itsupersedes BS EN 10051:1991+A1:1997 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee ISE/103, Structural Steels Other Than Reinforcements.A list of organizations represented
3、 on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2010ISBN 978 0 580 67084 8ICS 77.140.50Compliance with a British Standard cannot confer immunity
4、 fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2010.Amendments issued since publicationDate Text affectedBS EN 10051:2010EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10051 November 2010 ICS 77.140.50
5、 Supersedes EN 10051:1991 + A1:1997English Version Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape Bandes lamines chaud en continu, bandes et tles issues de larges bandes lamines chaud en aciers allis et non allis -
6、 Tolrances sur les dimensions et la forme Kontinuierlich warmgewalztes Band und Blech abgelngt aus Warmbreitband aus unlegierten und legierten Sthlen -Grenzabmae und Formtoleranzen This European Standard was approved by CEN on 23 October 2010. CEN members are bound to comply with the CEN/CENELEC Int
7、ernal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN me
8、mber. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN mem
9、bers are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain
10、, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Mem
11、bers. Ref. No. EN 10051:2010: EBS EN 10051:2010EN 10051:2010 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and definitions .44 Information to be supplied by the purchaser .54.1 General 54.2 Options .54.3 Designation 55 Form of supply .56 Tolerances for sheet/plate 66.1 Thick
12、ness .66.2 Length .86.3 Width .86.4 Flatness 96.5 Edge camber . 106.6 Out-of-squareness 106.7 Superimposement of dimensions . 107 Tolerances for wide strip and strip split from wide strip . 107.1 General . 107.2 Thickness 107.3 Width 117.4 Flatness . 117.5 Edge camber . 128 Measurement . 128.1 Gener
13、al . 128.2 Thickness 128.3 Length of sheet/plate 128.4 Width 128.5 Flatness for sheet/plate 128.6 Edge camber . 128.7 Out-of-squareness for sheet/plate 13Annex A (informative) Standards with steel grades for this dimensional standard . 14Annex B (normative) Options . 16BS EN 10051:2010EN 10051:2010
14、(E) 3 Foreword This document (EN 10051:2010) has been prepared by Technical Committee ECISS/TC 103 “Structural steels other than reinforcements”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical te
15、xt or by endorsement, at the latest by May 2011, and conflicting national standards shall be withdrawn at the latest by May 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for
16、 identifying any or all such patent rights. This document supersedes EN 10051:1991+A1:1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, C
17、zech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 10051:2010EN 10051:2010 (E) 4 1 Scop
18、e This European Standard specifies tolerances on dimensions and shape for continuously hot-rolled uncoated plate/sheet and strip with a maximum width of 2 200 mm of non-alloy and alloy steels in accordance with Table 1 (see also Annex A). This European Standard also applies to hot-rolled strip for c
19、old rolling. Table 1 Field of application Product Thickness mm Steel grades according to: (but not limited to) wide strip (width: 600 mm w 2 200 mm), Sheet/Plate cut from wide strip, strip w 10 mm (see 6.3); h) tolerances on flatness for sheet/plate of category D (see 6.4.2 and Table 10); i) edge ca
20、mber requirements for strip 1 800 t 2,00 0,13 0,14 0,16 2,00 1 800 t 2,00 0,17 0,19 0,21 2,00 1 800 t 2,00 0,20 0,22 0,24 2,00 1 800 t 2,00 0,22 0,25 0,27 2,00 1 800 t 2,00 0,24 0,27 0,29 2,00 1 850 0 +25 0 +6 aTolerances for trimmed edges apply to products with nominal thickness t 10 mm; for nomina
21、l thickness t 10 mm the upper tolerances shall be agreed at the time of enquiry and order.6.4 Flatness 6.4.1 For continuously hot-rolled low carbon sheet/plate of steels with a specified minimum yield strength Re 300 MPa (category A) the deviation from flatness shall not exceed the tolerances given
22、in Table 9. Closer flatness tolerances shall be agreed at the time of enquiry and order (see Annex B, option c). Table 9 Tolerances on flatness for steels with a specified minimum yield strength Re 300 MPa (category A) Dimensions in mm Nominal thickness t Nominal width w Tolerances on flatness Speci
23、al tolerances on flatness t 2,00 w 1 200 18 9 1 200 1 500 25 132,00 1 500 23 12 6.4.2 For continuously hot-rolled low carbon sheet/plate of steels with a specified minimum yield strength 300 MPa 1 500 28 38 aThe categories B, C and D are defined in 6.1.2 and Tables 4 to 6. 6.5 Edge camber The edge c
24、amber shall not exceed 0,5 % of the actual length of the sheet/plate for a nominal length l 5 000 mm. For sheet/plate with a nominal length l 5 000 mm and widths w 600 mm, the edge camber shall not exceed 20 mm for any length of 5 000 mm in the case of sheet/plate with mill edges and 15 mm in the ca
25、se of sheet with trimmed edges. 6.6 Out-of-squareness The out-of-squareness u measured in accordance with 8.7 shall not exceed 1,0 % of the actual width of the sheet/plate. 6.7 Superimposement of dimensions By agreement at the time of enquiry and order the upper tolerances on out-of-squareness and e
26、dge camber may be replaced by a requirement that a perfect rectangle formed by the ordered width and length dimensions can be superimposed into the sheets delivered (see Annex B, option e). In this case, the upper tolerances on width and length shall be agreed at the time of enquiry and order. 7 Tol
27、erances for wide strip and strip split from wide strip 7.1 General The specified values for tolerances shall not apply to the uncropped ends of the coil for a total length l, which is calculated using the formula. l (m) = (mm)thicknessnominal90provided that the result does not exceed 20 m. 7.2 Thick
28、ness 7.2.1 The tolerances on thickness shall be the same as those for sheet/plate (see 6.1). BS EN 10051:2010EN 10051:2010 (E) 11 7.2.2 Maximum values for crown as given in Table 11 and permissible thickness differences within one coil as given in Table 12 shall apply for hot-rolled strip for cold r
29、olling, if agreed at the time of enquiry and order (see Annex B, option f). The thickness (within one coil) shall change gradually and the changes shall not be discontinuous. NOTE For coils not slit in longitudinal direction the crown should be aimed to be as constant and symmetrical from the middle
30、 of the coil as possible. 7.2.3 More severe tolerances on thickness and crown may be agreed at the time of enquiry and order (see Annex B, option g). Table 11 Maximum values for crown for hot-rolled strip for cold rolling Dimensions in mm Nominal width w Permissible crown for steel category aA B C D
31、 w 1 200 0,10 0,12 0,13 0,14 1 200 w 1 500 0,13 0,15 0,17 0,18 1 500 w 1 800 0,16 0,18 0,21 0,22 1 800 w 2 200 0,20 0,23 0,26 0,28 aThe values for permissible crown shall be lowered by 20 % for hot-rolled strip slit from wide strip meant for cold rolling. Table 12 Permissible thickness differences w
32、ithin one coil of hot-rolled strip coil for cold rolling Dimensions in mm Nominal thickness t Permissible thickness differences for nominal width of strip w 1 200 1 200 w 1 500 1 500 w 2 200 0,8 t 2,0 0,20 0,24 0,28 2,0 t 3,0 0,22 0,27 0,333,0 t 4,0 0,28 0,32 0,40 4,0 t 8,0 0,28 0,32 0,407.3 Width T
33、he tolerances on width for strip shall be the same as for sheet/plate (see 6.3). 7.4 Flatness Requirements concerning flatness shall be agreed at the time of enquiry and order. Any requirements agreed shall take into account the processing equipment at the users disposal. BS EN 10051:2010EN 10051:20
34、10 (E) 12 7.5 Edge camber For strip w 600 mm, the edge camber shall not exceed 20 mm for any length of 5 000 mm in the case of strip with mill edges and 15 mm in the case of strip with trimmed edges. For strip w 600 mm slit from wide strip, the tolerances on edge camber shall be agreed at the time o
35、f enquiry and order. 8 Measurement 8.1 General Measurements listed in 8.2 to 8.7 shall be used in case of dispute and be carried out at ambient temperature. 8.2 Thickness 8.2.1 The thickness shall be measured at any point situated at least 40 mm from the edges for products with mill edges and at lea
36、st 25 mm from the edges for products with trimmed/slit edges. For coils with uncropped ends, 7.1 shall be considered. 8.2.2 The crown shall be measured as the thickness difference between the centre line of the product and a measuring point at 40 mm from any edge of the product in case of mill edges
37、 and at 25 mm in case of trimmed/slit edges. 8.2.3 The difference in thickness within one coil shall be measured at a line with an invariable distance from the longitudinal edges (minimum distance from the edges in accordance with 8.2.1). 8.3 Length of sheet/plate The length of the sheet/plate is th
38、e length of the shorter of both longitudinal edges. 8.4 Width The width shall be measured at right angles to the longitudinal axis of the product. 8.5 Flatness for sheet/plate Deviation from flatness for sheet/plate shall be determined by measuring the deviation in distance between the product and a
39、 flat horizontal surface on which it is placed. 8.6 Edge camber The edge camber is the maximum deviation of a longitudinal edge from a straight edge measuring base applied to it. The camber is measured on the concave edge (see Figure 1). For sheet/plate measuring base shall be the length of the prod
40、uct for a nominal length l 5 000 mm. For strip and sheet/plate with a nominal length l 5 000 mm, the measuring base shall be 5 000 mm, taken anywhere along the edge but excluding the uncropped ends. BS EN 10051:2010EN 10051:2010 (E) 13 Figure 1 Measurement of edge camber Key 1 Edge Camber 2 Side edg
41、e (concave side) 3 Straight edge a Rolling direction 8.7 Out-of-squareness for sheet/plate The out-of-squareness u for sheet/plate is the orthogonal projection of a transverse edge over a longitudinal edge (see Figure 2). Key 1 Out-of squareness u 2 Square 3 Side edge a Rolling direction Figure 2 Me
42、asurement of out-of-squareness BS EN 10051:2010EN 10051:2010 (E) 14 Annex A (informative) Standards with steel grades for this dimensional standard EN 10025-2, Hot rolled products of structural steels Part 2: Technical delivery conditions for non-alloy structural steels EN 10025-3, Hot rolled produc
43、ts of structural steels Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels EN 10025-4, Hot rolled products of structural steels Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels EN 10025-5
44、, Hot rolled products of structural steels Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance EN 10025-6:2004+A1:2009, Hot rolled products of structural steels Part 6: Technical delivery conditions for flat products of high yield strength struc
45、tural steels in the quenched and tempered condition EN 10028-2, Flat products made of steels for pressure purposes Part 2: Non-alloy and alloy steels with specified elevated temperature properties EN 10028-3, Flat products made of steels for pressure purposes Part 3: Weldable fine grain steels, norm
46、alized EN 10028-4, Flat products made of steels for pressure purposes Part 4: Nickel alloy steels with specified low temperature properties EN 10028-5, Flat products made of steels for pressure purposes Part 5: Weldable fine grain steels, thermomechanically rolled EN 10028-6, Flat products made of s
47、teels for pressure purposes Part 6: Weldable fine grain steels, quenched and tempered EN 10083-2, Steels for quenching and tempering Part 2: Technical delivery conditions for non-alloy steels EN 10083-3, Steels for quenching and tempering Part 3: Technical delivery conditions for alloy steels EN 100
48、84, Case hardening steels Technical delivery conditions EN 10085, Nitriding steels Technical delivery conditions EN 10111, Continuously hot-rolled low carbon steel sheet and strip for cold forming Technical delivery conditions EN 10120, Steel sheet and strip for welded gas cylinders EN 10149-2, Hot
49、rolled flat products made of high yield strength steels for cold forming Part 2: Delivery conditions for thermomechanically rolled steels EN 10149-3, Hot-rolled flat products made of high yield strength steels for cold forming Part 3: Delivery conditions for normalized or normalized rolled steels EN 10207, Steels for simple pressure vessels Technical delivery requiremen
