BS EN 10223-1-2012 Steel wire and wire products for fencing and netting Zinc and zinc-alloy coated steel barbed wire《栏栅用钢丝和金属丝制品 锌和锌合金包覆的刺钢丝》.pdf

上传人:outsidejudge265 文档编号:569788 上传时间:2018-12-13 格式:PDF 页数:14 大小:995.64KB
下载 相关 举报
BS EN 10223-1-2012 Steel wire and wire products for fencing and netting Zinc and zinc-alloy coated steel barbed wire《栏栅用钢丝和金属丝制品 锌和锌合金包覆的刺钢丝》.pdf_第1页
第1页 / 共14页
BS EN 10223-1-2012 Steel wire and wire products for fencing and netting Zinc and zinc-alloy coated steel barbed wire《栏栅用钢丝和金属丝制品 锌和锌合金包覆的刺钢丝》.pdf_第2页
第2页 / 共14页
BS EN 10223-1-2012 Steel wire and wire products for fencing and netting Zinc and zinc-alloy coated steel barbed wire《栏栅用钢丝和金属丝制品 锌和锌合金包覆的刺钢丝》.pdf_第3页
第3页 / 共14页
BS EN 10223-1-2012 Steel wire and wire products for fencing and netting Zinc and zinc-alloy coated steel barbed wire《栏栅用钢丝和金属丝制品 锌和锌合金包覆的刺钢丝》.pdf_第4页
第4页 / 共14页
BS EN 10223-1-2012 Steel wire and wire products for fencing and netting Zinc and zinc-alloy coated steel barbed wire《栏栅用钢丝和金属丝制品 锌和锌合金包覆的刺钢丝》.pdf_第5页
第5页 / 共14页
点击查看更多>>
资源描述

1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 10223-1:2012Steel wire and wire products for fencing and nettingPart 1: Zinc and zinc-alloy coated steel barbed wireBS EN 10223-1:2012 BRITISH STANDARDNational forewordThis

2、 British Standard is the UK implementation of EN 10223-1:2012. It supersedes BS EN 10223-1:1998, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e I S E / 1 0 6 , W i r e R o d a n d W i r e .A list of organizations represented on this co

3、mmittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012.ISBN 978 0 580 64498 6 ICS 7

4、7.140.65 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 10223-1:2012EUROPE

5、AN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10223-1 November 2012 ICS 77.140.65 Supersedes EN 10223-1:1997English Version Steel wire and wire products for fencing and netting - Part 1: Zinc and zinc-alloy coated steel barbed wire Fils et produits trfils en acier pour cltures et grillages - Partie

6、 1: Ronces en acier revtu de zinc ou dalliage de zinc Stahldraht und Drahterzeugnisse fr Zune und Drahtgeflechte - Teil 1: Stacheldraht aus Stahl, mit Zink oder Zinklegierung berzogen This European Standard was approved by CEN on 13 October 2012. CEN members are bound to comply with the CEN/CENELEC

7、Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to

8、 any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the officia

9、l versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, No

10、rway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in

11、 any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10223-1:2012: EBS EN 10223-1:2012EN 10223-1:2012 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 Information to be supplied by the purchaser .54 Manufacture 64.1 Base metal 64.2 Fabric

12、ation 64.2.1 General 64.2.2 Conventional barbed wire (C) .64.2.3 Reverse twist type (RT) .64.2.4 Barbed wire entanglement (BWE) 64.3 Welding .75 Requirements .76 Sampling and testing 87 Inspection documentation 88 Methods of test 88.1 Mechanical 88.2 Dimensions .88.3 Zinc and zinc-alloy coatings .88

13、.4 Barb spacing 89 Packaging .9Annex A (informative) Typical barbed wire formation (other types of barbed wire may be available) 10BS EN 10223-1:2012EN 10223-1:2012 (E) 3 Foreword This document (EN 10223-1:2012) has been prepared by Technical Committee ECISS/TC 106 “Wire rod and wires”, the secretar

14、iat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2013, and conflicting national standards shall be withdrawn at the latest by May 2013. Attention is drawn to the

15、possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10223-1:1997. EN 10223 “Steel wire and wire products for fencing and netting“ consis

16、ts of the following parts: Part 1: Zinc and zinc-alloy coated steel barbed wire Part 2: Hexagonal steel wire netting for agricultural, insulation and fencing purposes Part 3: Hexagonal steel wire mesh products for engineering purposes Part 4: Steel wire welded mesh fencing Part 5: Steel wire woven h

17、inged joint and knotted mesh fencing Part 6: Steel wire chain link fencing Part 7: Steel wire welded panels for fencing Part 8: Welded mesh gabion products According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this E

18、uropean Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia,

19、Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 10223-1:2012EN 10223-1:2012 (E) 4 Introduction There are many types of barbed wire. This standard specifies three types of barbed wire, conventional (C), reverse twist (RT) and barbed wire entanglement (BWE). Drawings of typi

20、cal conventional and reverse twist barbed wire are given for information in Annex A, Figures A.1 and A.2. BS EN 10223-1:2012EN 10223-1:2012 (E) 5 1 Scope This European Standard specifies zinc coated and zinc alloy coated steel barbed wire, conventional and reverse twist consisting of two stranded li

21、ne wires, around which the barbs are tightly wound, a twist being imparted between the barbs to restrict their movement. The barbed wire entanglement has a single line wire, around which the barbs are wound. 2 Normative references The following documents, in whole or in part, are normatively referen

22、ced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021, General technical delivery conditions for steel products EN 10204,

23、 Metallic products Types of inspection documents EN 10218-1, Steel wire and wire products General Part 1: Test methods EN 10218-2:2012, Steel wire and wire products General Part 2: Wire dimensions and tolerances EN 10244-1, Steel wire and wire products Non-ferrous metallic coatings on steel wire Par

24、t 1: General principles EN 10244-2:2009, Steel wire and wire products Non-ferrous metallic coatings on steel wire Part 2: Zinc or zinc alloy coatings EN ISO 16120-1, Non-alloy steel wire rod for conversion to wire Part 1: General requirements (ISO 16120-1) EN ISO 16120-2, Non-alloy steel wire rod fo

25、r conversion to wire Part 2: Specific requirements for general-purpose wire rod (ISO 16120-2) 3 Information to be supplied by the purchaser The following information shall be supplied by the purchaser at the time of enquiry and order: a) number of this European Standard; b) quantity; c) type of barb

26、ed wire; d) coating type; e) barb spacing (mm); f) length on reels (m); g) in the case of barbed wire entanglement (BWE) the type of finish; h) whether uniformity of coating is to be measured; i) inspection documentation requirements; j) agreed quality characteristics for testing (see Clause 6). BS

27、EN 10223-1:2012EN 10223-1:2012 (E) 6 EXAMPLE Barbed wire in accordance with EN 10223-1 / 10 reels / Reverse twist / class A zinc coating / 100 mm / 250 m / not applicable / no / inspection documents (non specific testing) in accordance with EN 10204 / min. strand breaking load, coat weight. 4 Manufa

28、cture 4.1 Base metal The base metal of the barbed wire shall be of a good commercial quality steel wire, selected from EN ISO 16120-1 and EN ISO 16120-2 and in a condition suitable for manufacture into barbed wire and base wire having the properties specified in the following Table 1. 4.2 Fabricatio

29、n 4.2.1 General The wire shall be zinc coated or zinc alloy coated to EN 10244-2, before fabrication into barbed wire, except for barbed wire entanglement, which may be made from bright wire and suitably finish coated (other than zinc) as the final product. 4.2.2 Conventional barbed wire (C) 4.2.2.1

30、 The conventional barbed wire shall be formed from two line wires complying with 4.1 and Table 1, twisted together with an approximate lay of 50 mm. Typical barb spacing is 75 mm 7 mm, or 100 mm 10 mm (or other spacing by agreement). Barb spacing shall be measured in accordance with 8.4. 4.2.2.2 The

31、 barbs shall be tightly wrapped round the two stranded line wires by a method that prevents slipping, to expose the four barbs at an angle of approximately 90 apart in a plane at right angles to the axis of the line wire (see Figure 1). The barbs shall project a distance of 12,5 mm 3,5 mm from the c

32、entreline of the wire and the barb ends shall be cut at an angle not greater than 35 to the axis of the barb. 4.2.3 Reverse twist type (RT) 4.2.3.1 The barbed wire shall be formed from two line wires complying with 4.1 and Table 1, twisted together alternately with an approximate lay of 25 mm, typic

33、al barb spacing is 75 mm 7 mm, or 100 mm 10 mm (or other spacing by agreement). Barb spacing shall be measured in accordance with 8.4. 4.2.3.2 The barbs shall be formed by tightly wrapping round the two stranded line wires to expose the four barbs in a fixed position at an angle of approximately 90

34、apart in a plane at right angles to the axis of the line wires. The barbs shall project a distance of 12,5 mm 3,5 mm from the centreline of the wire and the barb ends shall be cut at an angle not greater than 35 to the axis of the barb. 4.2.3.3 The barbed wire shall not start to unwind until 75 % of

35、 the total nominal breaking load is applied. The unwinding of the barbed wire occurs when the stranded wires no longer extend under the influence of the applied load. The wires start to unravel in such a way that the number of twists of the wire around each other diminishes. This is noticeable in th

36、e stress-strain curve of the tensile test, where the first major drop in stress occurs. The tensile test shall be performed on a sample of two barb spacing. 4.2.4 Barbed wire entanglement (BWE) 4.2.4.1 The entanglement shall be formed from wire complying with 4.1 and Table 1. The single line wire sh

37、all be crimped to an approximate pitch of 16 mm and approximate amplitude of 1 mm excluding the wire diameter. BS EN 10223-1:2012EN 10223-1:2012 (E) 7 4.2.4.2 The barbed wire shall be formed from one crimped line wire with four point barbs spaced at intervals between centres of 60 mm 15 mm. The barb

38、s shall be formed by wrapping round the line wire approximately four turns to expose the barbs in a fixed position at an angle of approximately 90 apart in a plane at right angles to the axis of the line. The barbs shall project a distance of 15 mm to 20 mm from the centreline of the wire and the ba

39、rb ends shall be cut at an angle not greater than 35 to the axis of the barb. 4.2.4.3 The barbed wire entanglement shall be supplied as a uniform cylindrical coil complying with (a) or (b) as follows: a) 68 turns 1 m 0,15 m in diameter, with adjacent turns clipped together in a diamond pattern, the

40、coil being capable of being extended to a length of 15 m; b) 32 turns 0,50 m 0,1 m diameter, clipped together in a diamond pattern, the coil being capable of being extended to a length of 6 m. 4.2.4.4 Along the length of the coil, adjacent turns in the coil shall be fastened together with five rows

41、of clips made from austenitic stainless steel in the softened condition or galvanized steel. The rows of clips shall be spaced around the circumference of the coils at 72 10 intervals. The start and end of the coil shall also be fitted with two additional clips 50 mm apart to secure the ends of the

42、coil. The clips shall be completely closed round the two wires, but allowing sufficient movement to permit the formation of the concertina when the coil is extended, without the line wire being permanently deformed at the clips. If the entanglement is manufactured from bright wire a finish should be

43、 applied, such as bitumastic (by spraying or by dipping) to provide durability during weather. 4.3 Welding Joining of individual wires by means of an electric butt weld is permitted provided such joints are 10 m apart and are made in a workmanlike manner. The weld area shall be suitably protected ag

44、ainst corrosion. 5 Requirements Before fabricating into barbed wire, the zinc or zinc alloy coated wire shall be tested for coating mass in accordance with EN 10244-2:2009 complying with class A for Zn coatings and class B for Zn95/Al5 alloys (for similar service life), adherence and where specified

45、, the uniformity of the coating. Where samples are taken from the fabricated barbed wire then the specified minimum coating mass shall be reduced by 5 % and if specified the minimum number of dips by one half minute. The nominal diameters, minimum tensile strengths and breaking loads of barbed wire

46、shall be as in Table 1. Tolerances on dimensions shall comply with EN 10218-2:2012, T1, for galvanized wire and EN 10218-2:2012, T3, for bright wire. BS EN 10223-1:2012EN 10223-1:2012 (E) 8 Table 1 Nominal diameters, minimum tensile strengths and breaking loads for barbed wire Wire type Type of barb

47、ed wire Nominal wire diameter Minimum tensile strength of wire Minimum strand breaking load amm N/mm2N Line Conventional Reverse twist BWE 2,20 2,40 2,50 2,70 1,70 3,00 350 350 350 350 950 1 250 2 660 3 166 3 434 4 008 4 230 8 836 Barbs Conventional and BWE Reverse twist 2,00 1,50 350 350 Non applic

48、able Non applicable aThe minimum strand breaking load shall be the overriding criterion. Strand breaking load is the maximum force during the tensile test before breaking. 6 Sampling and testing The manufacturer shall be responsible for the control of product quality by the application of statistica

49、l methods of sampling and analysis of results or, alternatively, by sampling and testing for the agreed quality characteristics at a rate of one reel in fifty. 7 Inspection documentation Non-specific testing and inspection documentation shall be provided according to EN 10021 and EN 10204. 8 Methods of test 8.1 Mechanical Mechanical tests shall be carried out in accordance with EN 10218-1. 8.2 Dimensions Dimensions shall be measured in accordance with EN

展开阅读全文
相关资源
  • BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdfBS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf
  • BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdfBS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf
  • BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdfBS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf
  • BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdfBS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf
  • BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdfBS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf
  • BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdfBS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf
  • BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdfBS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf
  • BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdfBS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf
  • BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdfBS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf
  • BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdfBS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > BS

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1