1、BS EN 10314:2016Method for the derivationof minimum values of proofstrength of steel at elevatedtemperaturesBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS EN 10314:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 10314:20
2、16. Itsupersedes BS EN 10314:2002 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee ISE/107, Steels for Pressure Purposes.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to
3、 include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI StandardsLimited 2016ISBN 978 0 580 84031 9ICS 77.140.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This
4、British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2016.Amendments issued since publicationDate Text affectedBS EN 10314:2016EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 10314 June 2016 ICS 77.140.30 Supersedes EN 10314:2002English Ver
5、sion Method for the derivation of minimum values of proof strength of steel at elevated temperatures Mthode de drivation des valeurs minimales de la limite conventionnelle dlasticit des aciers tempratures leves Verfahren zur Ableitung von Mindestwerten der Dehngrenze von Stahl bei erhhten Temperatur
6、en This European Standard was approved by CEN on 18 March 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical re
7、ferences concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a
8、CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedo
9、nia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey andUnited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPI
10、SCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2016 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10314:2016 EBS EN 10314:2016EN 10314:2016 (E) 2 Contents Page European foreword 3 Introd
11、uction 4 1 Scope 5 2 Normative references 5 3 Terms and definitions . 5 4 Symbols and abbreviations . 5 5 Method 6 5.1 Input data groups 6 5.2 Ratio values . 6 5.3 Minimum proof strength values 6 5.4 Minimum yield strength values . 7 6 Application of the method . 7 6.1 Representative data groups 7 6
12、.2 Number of data 8 6.3 Consistency of data . 8 6.4 Result . 8 Annex A (informative) Significant changes to the previous version EN 10314:2002 . 10 Bibliography 11 BS EN 10314:2016EN 10314:2016 (E) 3 European foreword This document (EN 10314:2016) has been prepared by Technical Committee ECISS/TC 10
13、7 “Steels for pressure purposes”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2016, and conflicting national standards shall be withdrawn at t
14、he latest by December 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10314:2002. Regarding the most
15、 significant technical changes that have been made in this new edition of EN 10314, see Annex A. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cypr
16、us, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United
17、 Kingdom. BS EN 10314:2016EN 10314:2016 (E) 4 Introduction Minimum values for tensile properties are specified in European Standards for steels and other metals for elevated temperature service. Such values are used to determine design strength values particularly where the materials are used in pre
18、ssure systems. Two International Standards, ISO 2605-1 and ISO 2605-2 (meanwhile withdrawn) were adopted by CEN as European Prestandards, ENV 22605-1 and ENV 22605-2. They set out procedures, based on statistical assessments of bodies of data, for the derivation and verification of minimum values of
19、 0,2 % proof strength at elevated temperatures. These procedures determine the minimum values from lower confidence lines. A third International Standard, ISO 2605-3, adopted by CEN as ENV 22605-3, sets out procedures for determining minimum values from the average trend behaviour of the property of
20、 interest as a function of temperature. One of the purposes of the procedures in ISO 2605-1 and ISO 2605-2 (ENV 22605-1 and ENV 22605-2) is to give an alternative to the requirement for elevated temperature tensile acceptance tests on individual products by organizations and manufacturers contributi
21、ng data for assessment and as a result of this to reduce the test frequency. Experience has shown that the procedures in ISO 2605-1 and ISO 2605-2 (ENV 22605-1 and ENV 22605-2) have limitations affecting the relationship between derived minimum property values and the minima of the test data arising
22、 from the statistical and some subjective decisions at various stages of the procedures. They also require relatively large amounts of data to produce an acceptable level of accuracy. The procedure set out in ISO 2605-3 (ENV 22605-3) requires less data but because it is designed to always give conse
23、rvative values from few data can give non-representative results. However, the principle of this procedure is considered to be more realistic and is adopted as the basis of this European Standard; the objective is to produce an assessment procedure for tensile property data which is simple to operat
24、e, gives representative results and is usable in computerized form. This European Standard, which supersedes EN 10314:2002, which in turn superseded ENV 22605-1, 2 and 3, sets out a method for deriving minimum proof strength values for steels at elevated temperatures with the intention that such val
25、ues are specified in relevant product standards. This European Standard does not specify a frequency of testing for the product standards where EN 10314 is applied. Verification of tensile properties at elevated temperatures is normally specified in the relevant product standard using the minimum pr
26、operty values derived by the procedure established in this European Standard. The method has been tested for proof strength values of steel. However, it is considered that the method can also be applied for the derivation of minimum values of tensile strength at elevated temperatures. BS EN 10314:20
27、16EN 10314:2016 (E) 5 1 Scope This European Standard specifies a method for deriving the minimum proof strength values for steels at elevated temperatures. However, this European Standard does not specify a verification procedure. 2 Normative references The following documents, in whole or in part,
28、are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN ISO 6892-1, Metallic materials Tensile testing Par
29、t 1: Method of test at room temperature (ISO 6892-1) EN ISO 6892-2, Metallic materials Tensile testing Part 2: Method of test at elevated temperature (ISO 6892-2) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 data set property value data fr
30、om room and elevated temperatures from the product selected for testing Note 1 to entry: This data can include averaged values where more than one set of tests at a given temperature representing one location is carried out. 3.2 data group property value data from X data sets as used for each assess
31、ment 3.3 result set ratio values for each data set 4 Symbols and abbreviations For the purposes of this document, the following symbols apply. t elevated temperature in C; f(t)ratio value; property value at elevated temperature t (in C) divided by property value at room temperature; fav(t)the f(t)-
32、value resulting from the trend curve for a specified temperature; Reyield strength (in MPa1); Rpproof strength (in MPa1); 1) 1 MPa = 1 N/mm. BS EN 10314:2016EN 10314:2016 (E) 6 Rp(t)/Rp(20)ratio value; proof strength at elevated temperature t divided by proof strength value at room temperature (20 C
33、); srresidual scatter. 5 Method 5.1 Input data groups 5.1.1 For a given steel grade, input data, to form a data group, shall be established by tensile tests at: a) room temperature in accordance with EN ISO 6892-1; b) elevated temperature in accordance with EN ISO 6892-2. 5.1.2 The data shall be ide
34、ntified by reference to a product standard and a steel grade (steel name and/or steel number as appropriate). Where input data predates the publication of the European Standards detailed in 5.1.1 a) and 5.1.1 b) the sampling and tensile testing shall have been carried out in accordance with the rele
35、vant product standard. 5.1.3 Test pieces for tensile tests both at room and elevated temperatures shall be taken from the same product. The location of the test piece shall be in accordance with the relevant product standard. Test pieces shall be taken as close to each other as possible. 5.1.4 Input
36、 data shall clearly identify the test method used and all data within each set (see definitions) shall have been determined by the same method. 5.2 Ratio values Property values resulting from the tensile tests at elevated temperature in accordance with 5.1 are normalized by expressing each value as
37、a ratio f(t)of the equivalent property value at room temperature obtained in accordance with Subclause 5.1: ( )=tproperty value at elevated temperature in Cfproperty value at room temerature in CThe ratio values f(t)obtained for each data set constitute a result set. Each result set is plotted as a
38、function of temperature and the value fav(t)at each temperature is determined from a trend curve which passes through a ratio value of 1,0 at room temperature, see Figure 1. The trend curve should be determined by a recognized procedure, normally a polynomial curve with degree 1-4, using a recognize
39、d statistical procedure such as a “least squares” technique. Before fitting the trend curve the data shall be examined to determine whether it forms more than one population; where that is the case the data shall be examined in detail with respect to its pedigree (see 6.2) and where deemed necessary
40、 treated separately (see also 6.1 and 6.3). 5.3 Minimum proof strength values From the trend curve established and average ratio values fav(t)derived in accordance with 5.2, the minimum proof strength values Rp(t)min(where appropriate Remay be used instead of Rp) are determined by alternative applic
41、ation of one of the following procedures, depending on the lowest value of fav(t)achieved over the temperature range for which minimum proof strength values are required: BS EN 10314:2016EN 10314:2016 (E) 7 a) When fav(t) 0,4 within the range of temperature values of interest: ( ) ( ) ( )( )= 201,1
42、0,1p t min p min av tRR f NOTE 1 In deriving the formula a linear relationship has been anticipated between Rp(t)and Rp(20)at a given temperature t where the average ratio value fav(t)is the slope of the regression line which passes through the zero point, and where the standard deviation of the res
43、idual scatter sris set equal to 0,05 Rp(20)min. For the purpose of this standard the specified minimum proof strength value Rp(t)min at a given temperature t is defined as the proof strength value derived from the lower ( 2s) confidence level value for proof strength at a room temperature which is 0
44、,1 Rp(20)minhigher than the specified minimum proof strength value at room temperature. In terms of probability the minimum proof strength value Rp(t)minapproximately represents the value of Rp(t)on the 2s confidence level of a virtual data set the lowest room temperature proof strength value of whi
45、ch is equal to Rp(20)min. b) When fav(t) 0,4 within the range of temperature values of interest: 1) for 20 C t 250 C ( ) ( ) ( )( )= 200,05 20230p t min p min av ttRR f 2) for t 250 C ( ) ( ) ( )( )= 20 0,05p t min p min av tRR f NOTE 2 At those temperatures where fav(t) 0,4, method 5.3 b) would pro
46、vide lower Rp(t)values than method 5.3 a). 5.4 Minimum yield strength values If only minimum yield strength values at room temperature are defined, and minimum proof strength values at higher temperatures should be derived, the formulae in Subclause 5.3 apply under condition that Rp(20)minshall be r
47、eplaced by Re(20)min.In this case, f(t)shall be obtained from measured values of proof strength at elevated temperature and yield strength at room temperature. As proof strength values are lower than yield strength values at room temperature, special care is needed to establish the trend curve at lo
48、wer temperatures ( 200 C) and mixing of yield and proof strength values at room temperature should be avoided. 6 Application of the method 6.1 Representative data groups The method in accordance with Clause 5 shall be applied separately for each data group supplied for assessment representing groups
49、 of material specified in product standards on the basis of: steel grade; product form; heat treatment temperature range(s); BS EN 10314:2016EN 10314:2016 (E) 8 product thickness range; test piece location and orientation. Each data group shall be treated separately, unless it can be demonstrated that more than one data group belong to the same population (see 5.2). In the same population at a given temperature the range between the highest and the lowest ratio value should not be greater than 0,2. 6.2
