1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12034 : 1997 The Eu
2、ropean Standard EN 12034 : 1996 has the status of a British Standard ICS 83.180 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Self-adhesive tapes Measurement of the length of a roll of adhesive tapeBS EN 12034 : 1997 This British Standard, having been prepared under the dire
3、ction of the Consumer Products and Services Sector Board, was published under the authority of the Standards Board and comes into effect on 15 March 1997 BSI 1997 The following BSI references relate to the work on this standard: Committee reference PKW/3 Draft for comment 92/45149 DC ISBN 0 580 2672
4、9 6 Amendments issued since publication Amd. No. Date Text affected Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PKW/3, Distribution packaging, transport packaging and unit loads, upon which the following bodies were r
5、epresented: British Adhesive and Sealants Association British Apparel and Textile Confederation British Coatings Federation Ltd. British Fibreboard Packaging Association British Glass Manufacturers Confederation British Industrial Truck Association British Plastics Federation British Retail Consorti
6、um British Rubber Manufacturers Association Ltd. British Tensional Strapping Association Ltd. British Timber Merchants Association British Wood Preserving and Damp-proofing Association Chamber of Shipping Chemical Industries Association China Clay Association Cranfield Logistics Department of Transp
7、ort Engineering Equipment and Materials Users Association Federation of the Electronics Industry Flexible Ibc Association Food and Drink Federation Independent Pallet Repair Committee Institute of Grocery Distribution Metal Packaging Manufacturers Association Ministry of Defence National Association
8、 of Pallet Distributors Power Fastenings Association Pira International Road Haulage Association Ltd. Society of Occupational Medicine Storage Equipment Manufacturers Association Timber Packaging and Pallet Confederation Timber Research and Development Association United Kingdom Softwood Sawmillers
9、Association The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Adhesive Tape Manufacturers Association British Footwear Manufacturers Federation British Steel Industry (Wire Section) Packaging Distributors Association Pressure Sensitive Manu
10、facturers AssociationBS EN 12034 : 1997 BSI 1997 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 Text of EN 12034 3ii BSI 1997 BS EN 12034 : 1997 National foreword This British Standard has been prepared by Technical Committee PKW/3 and is the English langua
11、ge version of EN 12034 : 1996 Self-adhesive tapes Measurement of the length of a roll of adhesive tape, published by the European Committee for Standardization (CEN). Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprise
12、s a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 4, an inside back cover and a back cover.CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1996
13、 Copyright reserved to CEN memebers Ref. No. EN 12034 : 1996 E EUROPEAN STANDARD EN 12034 NORME EUROPE ENNE EUROPA ISCHE NORM May 1996 ICS 83.180 Descriptors: adhesive tapes, tests, dimensional measurement, length, elongation at break English version Self-adhesive tapes Measurement of the length of
14、a roll of adhesive tape Rubans auto-adhe sifs Mesure de la longeur dun rouleau de ruban adhe sif Klebeba nder Messung der La nge einer Klebebandrolle This European Standard was approved by CEN on 1996-04-19. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate th
15、e conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in
16、 three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies o
17、f Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 12034 : 1996 BSI 1997 Foreword This European Standard has been prepared by the Technical Committee CEN/TC 253, Se
18、lf-adhesive tapes, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 1996, and conflicting national standards shall be withdrawn at the latest by
19、November 1996. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Port
20、ugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Principle 3 3 Apparatus (see figure 1) 3 4 Test piece 3 5 Procedure 3 6 Expression of results 3 7 Test report 3Page 3 EN 12034 : 1996 BSI 1997 1 Scope This standard specifies a method to measure the length
21、of adhesive tape on a roll. For non-extensible adhesive tapes, the length measured by this method will be the same as the length after unrolling. For extensible adhesive tapes, the length after unrolling will be greater if the adhesive tape is stretched irreversibly by unrolling. It is also possible
22、 for an extensible adhesive tape to measure less after unrolling if stress built in during manufacture recovers after unrolling. This is important for all adhesive tapes with elongation at break of 80 % or greater. Provision is made for either including in or excluding from the total length the leng
23、th of that portion of adhesive tape that is in direct contact with the core. 2 Principle The length is calculated from a measurement of the number of turns of adhesive tape on the roll and a measurement of the outer circumference of the roll of adhesive tape and the outer circumference of the core.
24、3 Apparatus (see figure 1) 3.1 Measuring device which is capable of counting both whole revolutions and part revolutions, and which is continuously driven by a spindle. The spindle carries a suitable locking device, by which means a wedge-shaped shaft to suit the various internal diameters of cores
25、of the rolls of adhesive tape can be quickly fitted. (The wedge-shaped shaft, for example, for a nominal 25 mm internal diameter core, will go from 24,5 mm diameter to 26,5 mm diameter over a shaft length of 50 mm.) 3.2 Measuring tape. A narrow, flexible, steel tape graduated in millimetres. 4 Test
26、piece One roll of adhesive tape. 5 Procedure 5.1 Standard test conditions The test shall be carried out at 23 C 2C and 50 % 5 % relative humidity. 5.2 Measure the circumference in millimetres (C R )of the roll by means of a steel tape, applying the steel tape to the roll like a belt. 5.3 Mount the r
27、oll on the wedge-shaped shaft of the counter. Set the counter to zero and pull the adhesive tape from the roll in a direction perpendicular to the counter spindle. Remove all the adhesive tape from the core and record N, the number of revolutions (to the nearest tenth of a revolution) as read from t
28、he counter when the last layer of adhesive tape has left the core. 5.4 Measure the circumference of the core in millimetres (C 0 ). 6 Expression of results Calculate L, the length of the adhesive tape in metres, as follows: L=( C R + C 0 ) N 2000 If the length of adhesive tape in contact with the co
29、re is not to be included in the total length, then: L=( C R + C 0 ) 2 N 2000 C 0 1000 7 Test report The test report shall include the following information: a) a reference to this European Standard; b) all information necessary to identify the test sample; c) the date of the test; d) the results obt
30、ained; e) any operation not specified in this European Standard which may influence the results.Page 4 EN 12034 : 1996 BSI 1997 Dimensions in millimetres Figure 1. Measuring deviceblankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
31、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It p
32、resents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of
33、 BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996
34、 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Servic
35、es. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on na
36、tional, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Su
37、bscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI pu
38、blications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic
39、, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.
