1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12197 : 1997 The Eu
2、ropean Standard EN 12197 : 1997 has the status of a British Standard ICS 97.220.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Gymnastic equipment Horizontal bars Safety requirements and test methodsThis British Standard, having been prepared under the direction of the Con
3、sumer Products and Services Sector Board, was published under the authority of the Standards Board and comes into effect on 15 November 1997 BSI 1997 ISBN 0 580 28380 1 BS EN 12197 : 1997 Amendments issued since publication Amd. No. Date Text affected National foreword This British Standard is the E
4、nglish language version of EN 12197 : 1997. The UK participation in its preparation was entrusted to Technical Committee SW/14, Gymnasium and sports equipment, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the in
5、terpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards
6、which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. Compliance with a British
7、Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover.CEN European Committee for Standardization Comite Europe en de Normalisation Europ
8、a isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12197 : 1997 E EUROPEAN STANDARD EN 12197 NORME EUROPE ENNE EUROPA ISCHE NORM June 1997 ICS
9、 97.220.30 Descriptors: Sports equipment, gymnastic equipment, horizontal bars, classifications, dimensions, safety, specifications, stability, rigidity, marking, technical notices English version Gymnastic equipment Horizontal bars Safety requirements and test methods Mate riel de gymnastique Barre
10、s fixes Exigences de se curite et me thodes dessai Turngera te Reck Sicherheitstechnische Anforderungen und Pru fverfahren This European Standard was approved by CEN on 1997-05-16. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving thi
11、s European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (E
12、nglish, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech R
13、epublic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 12197 : 1997 BSI 1997 Foreword This European Standard has been prepared by Technical Committee CEN/TC 136, Sports, playgroun
14、d and other recreational equipment, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 1997, and conflicting national standards shall be withdrawn at
15、 the latest by December 1997. This European Standard is one of a package, each of which deals with a particular type or a particular group of gymnastic equipment. This European Standard should be read in conjunction with EN 913. According to the CEN/CENELEC Internal Regulations, the national standar
16、ds organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page
17、 Foreword 2 1 Scope 3 2 Normative references 3 3 Classification 3 4 Safety requirements 3 5 Information to be provided by the manufacturer/supplier 4 6 Marking 4 Annexes A (informative) Examples of types of bar support 5 B (informative) Example of fixing points type 3 6Page 3 EN 12197 : 1997 BSI 199
18、7 1 Scope This standard specifies specific safety requirements (see clause 4) for horizontal bars in addition to the general safety requirements in EN 913. This European Standard is applicable to three types of horizontal bars (see table 1). 2 Normative references This European Standard incorporates
19、 by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European St
20、andard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 913 : 1996 Gymnastic equipment General safety requirements and test methods 3 Classification Horizontal bars shall be classified by the design (types) in
21、 accordance with table 1. Table 1. Types Type Description Example 1 Horizontal bar fixed with ground sockets Figure 1 2 Horizontal bar fixed with floor plate and bolt Figure 2 3 Horizontal bar fixed with cables Figure 3 Figure 1. Horizontal bar type 1 Figure 2. Horizontal bar type 2 4 Safety require
22、ments 4.1 General Horizontal bars shall comply with the requirements of EN 913, except insofar as they are modified by this European Standard. 4.2 Dimensions The horizontal bars shall comply with the dimensions of table 2. Table 2. Dimensions Dimensions in millimetres Types Diameter of bar Length be
23、tween rotating points 1, 2 and 3 28 min. 41 max. 2 200 to 2 600 NOTE . Annex A indicates rotation parts of typical types of bar support. 4.3 Stability When tested in accordance with annex B of EN 913 : 1996, the equipment shall not tip in any direction when subjected to a horizontal force of 3 800 N
24、 at the mid point of the horizontal bar between its rotating points. NOTE. Annex B shows typical fixing arrangement for type 3 horizontal bars.Page 4 EN 12197 : 1997 BSI 1997 Figure 3. Horizontal bar type 3 4.4 Stiffness When tested in accordance with annex B of EN 913 : 1996, and with the bar set a
25、t maximum height the deflection of the bar shall be (100 10) mm when subjected to a vertical force of 2 000 N applied at the centre of the bar. 4.5 Residual deflection When tested in accordance with annex B of EN 913 : 1996, the bar shall not show any residual deflection when the test force of 2 000
26、 N is removed. 4.6 Structural integrity When tested in accordance with annex B of EN 913 : 1996, the equipment shall show no signs of fracture, rupture, or defects when subjected to a vertical force of 4 750 N at the midpoint of the horizontal bar between its rotating points. 5 Information to be pro
27、vided by the manufacturer/supplier An information booklet shall be provided by the manufacturer/supplier containing the following: a) type in accordance with table 1; b) assembly details covering method of adjustment; c) maintenance details; d) installation details. 6 Marking Marking shall comply wi
28、th EN 913 and in addition shall include: year of manufacture.Page 5 EN 12197 : 1997 BSI 1997 Annex A (informative) Examples of types of bar support The length of the bar corresponds to the distance between the rotation point of their supports.Page 6 EN 12197 : 1997 BSI 1997 Annex B (informative) Exa
29、mple of fixing points type 3 Dimensions in millimetres Figure B.1 Dimensions of fixing pointsblankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
30、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorp
31、orated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyon
32、e finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLU
33、S which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international sta
34、ndards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help
35、 to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive su
36、bstantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the interna
37、tional standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This
38、does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.
