BS EN 12813-2004 Temporary works equipment - Load bearing towers of prefabricated components - Particular methods of structural design《临时工程设备 预制构件的承重塔 结构设计的特殊方法》.pdf

上传人:eastlab115 文档编号:570781 上传时间:2018-12-13 格式:PDF 页数:22 大小:429.16KB
下载 相关 举报
BS EN 12813-2004 Temporary works equipment - Load bearing towers of prefabricated components - Particular methods of structural design《临时工程设备 预制构件的承重塔 结构设计的特殊方法》.pdf_第1页
第1页 / 共22页
BS EN 12813-2004 Temporary works equipment - Load bearing towers of prefabricated components - Particular methods of structural design《临时工程设备 预制构件的承重塔 结构设计的特殊方法》.pdf_第2页
第2页 / 共22页
BS EN 12813-2004 Temporary works equipment - Load bearing towers of prefabricated components - Particular methods of structural design《临时工程设备 预制构件的承重塔 结构设计的特殊方法》.pdf_第3页
第3页 / 共22页
BS EN 12813-2004 Temporary works equipment - Load bearing towers of prefabricated components - Particular methods of structural design《临时工程设备 预制构件的承重塔 结构设计的特殊方法》.pdf_第4页
第4页 / 共22页
BS EN 12813-2004 Temporary works equipment - Load bearing towers of prefabricated components - Particular methods of structural design《临时工程设备 预制构件的承重塔 结构设计的特殊方法》.pdf_第5页
第5页 / 共22页
点击查看更多>>
资源描述

1、BRITISH STANDARD BS EN 12813:2004 Temporary works equipment Load bearing towers of prefabricated components Particular methods of structural design The European Standard EN 12813:2004 has the status of a British Standard ICS 91.220 BS EN 12813:2004 This British Standard was published under the autho

2、rity of the Standards Policy and Strategy Committee on 1 December 2004 BSI 1 December 2004 ISBN 0 580 44835 5 National foreword This British Standard is the official English language version of EN 12813:2004. The UK participation in its preparation was entrusted by Technical Committee B/514, Access

3、and support equipment, to Subcommittee B/514/26, Falsework, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to

4、 in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions o

5、f a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or pro

6、posals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 18, an inside back cover and a back cover. The BS

7、I copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM EN12813 June2004 ICS91.220 Englishversion TemporaryworksequipmentLoadbearingtowersof prefabricatedcompon

8、entsParticularmethodsofstructural design EquipementstemporairesdechantiersToursdtaiement encomposantsprfabriqusMthodesparticuliresde calculdesstructures TemporreKonstruktionenfrBauwerkeSttzentrme ausvorgefertigtenBauteilenBesondere Bemessungsverfahren ThisEuropeanStandardwasapprovedbyCENon4December2

9、003. CENmembersareboundtocomplywiththeCEN/CENELECInternalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheCentralSecretariator

10、toanyCENmember. ThisEuropeanStandardexistsinthreeofficialversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheCentralSecretariathasthesamestatusast heofficial versions. CENmembersarethenationalstandardsbodies

11、ofAustria,Belgium,Cyprus,CzechRepublic,Denmark,Estonia,Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia,Lithuania,Luxembourg,Malta,Netherlands,Norway,Poland,Portugal, Slovakia, Slovenia,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENOR

12、MALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2004CEN Allrightsofexploitationinanyformandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.EN12813:2004:EEN 12813:2004 (E) 2 Contents Page 1 Scope5 2 Normative references5 3 Terms and definitions .5 4 Sym

13、bols8 5 General information needed for structural analysis of a load bearing tower made in prefabricated components9 6 Analysis methods for the design resistance of a tower 9 6.1 Cases to be analysed 9 6.2 Curve to be established for case 1a 10 6.3 Examination methods.11 1.4 Detail tests and global

14、tests .11 7 The result for the calculated and experimental results shall be such that no calculated value is greater than the corresponding experimental value. Documentation relating to the test 12 8 The test report shall be in accordance with clause 9 of EN 12811-3:2002. Documentation to be provide

15、d 12 8.1 General12 8.2 Information for the user 12 8.3 Information for the falsework designer .12 Annex A (informative) Procedure for analysis by first order theory of a fully triangulated load bearing tower .13 A.1 Example chosen.13 A.2 Determination of the buckling load, F crfor one face of the to

16、wer13 A.3 Structural analysis by first order theory .13 Annex B (normative) Global test procedure.15 B.1 Introduction15 B.2 Apparatus.15 B.3 Choice of components 15 B.4 Assembly of test tower .15 B.5 Test procedure.17 B.6 Data to be recorded .17 B.7 Additional requirements when a horizontal load is

17、also applied .17 EN 12813:2004 (E) 3 Foreword This document (EN 12813:2004) has been prepared by Technical Committee CEN/TC 053 “Temporary works equipment”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an i

18、dentical text or by endorsement, at the latest by December 2004, and conflicting national standards shall be withdrawn at the latest by December 2004. Annex A is informative, annex B is normative. This document includes a bibliography. According to the CEN/CENELEC Internal Regulations, the national

19、standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portuga

20、l, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 12813:2004 (E) 4 Introduction This European Standard is intended to provide information for those who specify load bearing towers made from prefabricated components and for the designer who has to prepare a scheme for their use

21、. This European Standard will be of interest to those who wish to develop particular items, or groups of items for load bearing towers of prefabricated components. This European Standard describes how to establish structural data for load bearing towers made from prefabricated components. Most of th

22、e figures illustrating the standard are of a particular type of tower but the procedures described are applicable to all towers. There is a requirement for a global test to demonstrate that the modelling adopted in the analysis is sufficiently accurate and on the conservative side. For materials thi

23、s standard refers only to valid European Standards. However a large stock of equipment made of materials conforming to standards no longer valid is in use. This standard does not cover the use of this equipment. NOTE This European Standard does not give information on site activities nor about safet

24、y requirements, for which reference should be made to E.C. directives, and national documents. EN 12813:2004 (E) 5 1 Scope This European Standard describes methods for establishing structural data for stiffness and resistance by calculation supported by tests for load bearing towers made of prefabri

25、cated components of steel or aluminium alloy. The vertical load capacity is established, both with or without horizontal loads and with the top restrained or free. This European Standard specifies two methods of analysis, by first order theory, or by second order theory. NOTE For definitions and req

26、uirements relating to structures and materials of the structure, specifications and loads, see EN 12812. The European Standard is not intended for towers constructed with tubes and couplers: it is expected that they will be designed in accordance with EN 12812. 2 Normative references This European S

27、tandard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply

28、 to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). ENV 1993-1-1, Eurocode 3 - Design of steel structures Part 1-1: General rules and rules for buildings. ENV 1999-1

29、-1, Eurocode 9 Design of aluminium structures Part 1-1: General rules - General rules and rules for buildings. EN 12810-2, Faade scaffolds made of prefabricated components Part 2: Particular methods of structural design EN 12811-2, Temporary works equipment - Part 2: Information on materials. EN 128

30、11-3:2002, Temporary works equipment - Part 3: Load testing. EN 12812:2004, Falsework Performance requirements and general design. 3 Terms and definitions For the purposes of this European Standard, the terms an definitions of EN 12812 and the following apply. 3.1 base plate plate used for spreading

31、 the load in a standard over a greater area 3.2 base jack base plate which has means of vertical adjustment NOTE It is intended to be positioned at the base of an upright. It usually incorporates a base plate. EN 12813:2004 (E) 6 3.3 bracing component or components to increase stiffness and to provi

32、de greater vertical and lateral strength NOTE In the horizontal plane this may comprise frames, platforms, or rigid linkages between the uprights. In the vertical plane the usual methods include closed frames, with or without gussets, open frames, ladder frames with open access, rigid assemblies bet

33、ween horizontal members and uprights, and diagonals. 3.4 fork head “U“ shaped component for holding a beam NOTE It is intended to be positioned at the top of an upright for locating and supporting a horizontal beam. 3.5 frame component which has at least one horizontal element permanently fixed to a

34、t least one upright element 3.6 fully triangulated load bearing tower tower in which a diagonal member is attached to each panel including either braced or unbraced jacks (see Figures 1a, 1b, 2) NOTE A panel is bounded by two adjacent vertical and two adjacent horizontal members. The diagonals are c

35、onsidered to create full triangulation to each vertical plane, if they are attached within 200 mm of each node point. 3.7 head jack screw device both able to adjust height and to release the tower from the loading. NOTE It is intended to be positioned at the top of an upright. It usually incorporate

36、s a fork head. 3.8 horizontal member component forming a horizontal connection between two uprights. NOTE An upright may either be the vertical linear element of frames, or vertical components of a modular system. 3.9 load bearing tower tower with three or more uprights made of prefabricated steel o

37、r aluminium alloy components NOTE The components are principally linear members or frames. 3.10 loading beam horizontal member positioned above the primary beams onto which the vertical imposed test load is centrally applied 3.11 not fully triangulated load bearing tower tower in which not all verti

38、cal planes are fully triangulated (see Figures 3a, 3b) 3.12 prefabricated component discrete part of a tower with permanently fixed connection devices which pre-determine dimensions EN 12813:2004 (E) 7 3.13 primary beam lowest horizontal beam distributing load at the top of a tower 3.14 storey part

39、of the tower comprised between two consecutive horizontal planes 3.15 upright vertical load bearing element a) with braced head jacks b) with unbraced jacks Figure 1 Examples of fully triangulated towers Figure 2 Eccentricity “e“ of the diagonals to members EN 12813:2004 (E) 8 a) with braced head ja

40、cks b) with unbraced jacks Figure 3 Examples of not fully triangulated towers 4 Symbols Table 1 Symbols Number Symbol Denomination Unit 1 A Cross-sectional area mm 2 d Horizontal displacement mm 3 e Eccentricity mm 4 E Longitudinal modulus of elasticity N/mm 5 F External load applied to the structur

41、e N 6 F H Horizontal load applied to the structure N 7 F Hd Design value of the horizontal load N 8 F v Vertical load applied to the structure N 9 F vd Design value of the vertical load N 10 F cr Buckling load of a face N 11 y nom Nominal yield stress N/mm 12 H, h Height m 13 L Length m 14 n Number

42、of uprights in a tower 15 R d Design value of resistance N/mm 16 S d Design value of the effects of actions N/mm 17 F Partial factor for the actions 18 M Partial factor for resistance 19 cr The lowest elastic buckling load factor to be applied to the design loads EN 12813:2004 (E) 9 5 General inform

43、ation needed for structural analysis of a load bearing tower made in prefabricated components See EN 12812:2004, for information about : materials, clause 5, (and also EN 12811-2) thickness of material, 7.2 partial factors, 9.2.2 imperfections and boundary conditions, 9.3 classes, clause4, 9.1.2 dif

44、ferential settlement and thermal conditions 8.3.2 actions, clause 8. 6 Analysis methods for the design resistance of a tower 6.1 Cases to be analysed A tower shall be analysed with the following three sets of loads, and with base and head Jacks fully extended, unless design resistance for smaller ex

45、tensions has to be established. Case 1 A tower unrestrained at the top subjected to vertical loading: Case 1a, Figure 4a) with horizontal loading Case 1b, Figure 4b) without horizontal loading Case 2 A tower with the top restrained , subjected to vertical loading (see Figures 4a), 4b), and 5). a) wi

46、th horizontal loading b) without horizontal loading For explanations of symbols see clause 4 Figure 4 Typical loading conditions for a tower free at the top EN 12813:2004 (E) 10 For explanations of symbols see clause 4 Figure 5 Typical loading conditions for a tower restrained at the top 6.2 Curve t

47、o be established for case 1a For case 1a), a curve shall be produced showing the combination of maximum resistances to vertical and horizontal loads, see Figure 6. Key F VVertical load F HHorizontal load Figure 6 Typical curve relating maximum vertical and horizontal loading EN 12813:2004 (E) 11 6.3

48、 Examination methods 6.3.1 Analysis by second order theory This method can be used with a bi-dimensional model or with a tri-dimensional model for all structural systems. For steel, this will be in accordance with ENV 1993-1-1. For aluminium alloy, this will be in accordance with ENV 1999-1-1. Detail tests shall be carried out in accordance with the principal requirements of EN 12810-2. In order to find the load bearing capacity of tower the structural analysis performed by using a second order approach shall be int

展开阅读全文
相关资源
  • BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdfBS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf
  • BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdfBS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf
  • BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdfBS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf
  • BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdfBS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf
  • BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdfBS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf
  • BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdfBS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf
  • BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdfBS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf
  • BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdfBS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf
  • BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdfBS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf
  • BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdfBS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > BS

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1