BS EN 13100-1-2017 Non destructive testing of welded joints of thermoplastics semi-finished products Visual examination《热塑性半成品焊接接头无损检验 目视检查》.pdf

上传人:visitstep340 文档编号:571090 上传时间:2018-12-13 格式:PDF 页数:12 大小:1.58MB
下载 相关 举报
BS EN 13100-1-2017 Non destructive testing of welded joints of thermoplastics semi-finished products Visual examination《热塑性半成品焊接接头无损检验 目视检查》.pdf_第1页
第1页 / 共12页
BS EN 13100-1-2017 Non destructive testing of welded joints of thermoplastics semi-finished products Visual examination《热塑性半成品焊接接头无损检验 目视检查》.pdf_第2页
第2页 / 共12页
BS EN 13100-1-2017 Non destructive testing of welded joints of thermoplastics semi-finished products Visual examination《热塑性半成品焊接接头无损检验 目视检查》.pdf_第3页
第3页 / 共12页
BS EN 13100-1-2017 Non destructive testing of welded joints of thermoplastics semi-finished products Visual examination《热塑性半成品焊接接头无损检验 目视检查》.pdf_第4页
第4页 / 共12页
BS EN 13100-1-2017 Non destructive testing of welded joints of thermoplastics semi-finished products Visual examination《热塑性半成品焊接接头无损检验 目视检查》.pdf_第5页
第5页 / 共12页
点击查看更多>>
资源描述

1、Non destructive testing of welded joints of thermoplastics semi-finished productsPart 1: Visual examinationBS EN 131001:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06National forewordThis British Standard is the UK implementation of EN 131001:2017. It supersede

2、s BS EN 131001:2000, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/80, Welding thermoplastics.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the n

3、ecessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 89660 6ICS 25.160.40Compliance with a British Standard cannot confer immunity from legal obligations. This British Standa

4、rd was published under the authority of the Standards Policy and Strategy Committee on 30 June 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 131001:2017EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 131001May 2017ICS 25.160.40 Supersedes EN 131001:1999

5、EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGCENCENELEC Management Centre: Avenue Marnix 17, B1000 Brussels 2017 CEN Ref. No. EN 131001:2017: EAll rights of exploitation in any form and by any means reserved worldwide for CEN national MembersNon d

6、estructive testing of welded joints of thermoplastics semifinished products Part 1: Visual examinationContrle non destructif des assemblages souds sur produits semi-finis en thermoplastiques Partie 1 : Contrle visuelZerstrungsfreie Prfung von Schweiverbindungen an Halbzeugen aus thermoplastischen Ku

7、nststoffen Teil 1: SichtprfungThis European Standard was approved by CEN on 10 March 2017.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Uptodate list

8、s and bibliographical references concerning such national standards may be obtained on application to the CENCENELEC Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under th

9、e responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugosl

10、av Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.English VersionEN 131001:2017 (E)European forew

11、ord 31 Scope . 42 Normative references 43 Test conditions and equipment . 44 Personnel . 45 Visual examination . 45.1 General . 45.2 Visual examination of joint preparation . 55.3 Visual examination during welding 55.4 Visual examination of the finished weld . 55.5 Visual examination of repaired wel

12、ds . 56 Test report . 5Bibliography 72Contents PageBS EN 131001:2017EN 131001:2017 (E)European forewordThis document (EN 13100-1:2017) has been prepared by Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN.This European Standard shall be given the status of a nationa

13、l standard, either by publication of an identical text or by endorsement, at the latest by November 2017, and conflicting national standards shall be withdrawn at the latest by November 2017.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent

14、 rights. CEN shall not be held responsible for identifying any or all such patent rights.This document supersedes EN 131001:1999.EN 13100, “Non destructive testing of welded joints of thermoplastics semi-finished products “, is currently composed with the following parts: Part 1: Visual examination;

15、 Part 2: X-ray radiographic testing; Part 3: Ultrasonic testing; Part 4: High voltage testing.According to the CENCENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus,

16、Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the Un

17、ited Kingdom.3BS EN 131001:2017EN 131001:2017 (E)1 ScopeThis European standard covers the visual examination of welds in thermoplastic materials. It may also be applied to visual testing of the joint prior to and during the welding.2 Normative referencesThe following documents, in whole or in part,

18、are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 14728, Imperfections in thermoplastic welds Classif

19、icationEN 16296, Imperfections in thermoplastics welded joints Quality levelsEN ISO 17637:2016, Non-destructive testing of welds Visual testing of fusion-welded joints (ISO 17637:2016)EN ISO 17659, Welding Multilingual terms for welded joints with illustrations (ISO 17659)3 Test conditions and equip

20、mentThe illuminance at the surface, shall be a minimum of 350 lx, 500 lx is recommended.For direct visual examination of welds, access shall be sufficient to allow the eye to be placed within a distance of 600 mm from the weld, around the whole weld and the viewing angle shall not be less than 30.Re

21、mote visual examination of welds using mirrors, boroscopes, fibre optics or cameras shall be considered as additional requirements and shall be specified by an application standard or by agreement between the contracting parties.If a good contrast and relief effect between imperfections and backgrou

22、nd is required, an additional light source can be used.The equipment (e.g.: gauges, callipers) used for the dimensional check of the weld shall ensure the necessary precision level, in accordance with the applicable acceptance criteria.Examples of examination equipment are given in EN ISO 17637:2016

23、, Annex A.4 PersonnelVisual examination of welds and the evaluation of results for final acceptance should be performed by personnel qualified and familiar with the relevant standards, rules, specifications and the welding procedure 1 used.It is recommended that personnel should be qualified in acco

24、rdance with EN ISO 9712 or an equivalent standard at an appropriate level in the relevant industry sector.5 Visual examination5.1 GeneralThe examination is normally performed on welds in the aswelded condition; however, for example when required by an application standard or by agreement between the

25、 contracting parties, the examination may be also carried out at other stages during the welding process, such as for checking the weld preparation and during the welding, for evaluating the effective application of the relevant welding procedure specification 1.4 BS EN 131001:2017EN 131001:2017 (E)

26、The extent of examination and the acceptance criteria of the imperfections shall be defined in advance by EN 16296, an application standard or by agreement between the contracting parties.The examiner shall have access to the necessary inspection and production documentation required.The classificat

27、ion of the imperfections can be found in EN 14728.The terms to be used are available in EN ISO 17659.5.2 Visual examination of joint preparationWhen visual examination is required prior to welding, the joint preparation shall be examined to check that the shape, dimensions and the cleaning condition

28、s of the weld preparation meet the specified requirements given in the relevant standards and/or in the applicable welding procedure specification 1.During this examination special attention should be paid to the correct fixing of the parts to be welded (e.g.: linear and angular alignment, gap).5.3

29、Visual examination during weldingWhen required, in the case of multipass welding processes, the weld shall be examined during the welding process to check that:a) each run is cleaned and/or scraped before it is covered by subsequent runs;b) there are no visible imperfections (such as cracks or cavit

30、ies), if imperfections are observed, they shall be reported immediately so that remedial action can be taken before the execution of the next run;c) the transition between the runs and between the weld and the parent material is so formed that satisfactory penetration can be accomplished when weldin

31、g the next run;d) after any necessary repairs/remedial action, the weld conforms to the original requirements of the welding procedure specification.5.4 Visual examination of the finished weldWelds shall be examined in the aswelded condition and shall also be examined after any surface treatment (if

32、 any).The finished weld shall be examined to determine whether it meets the requirements of the application or product standard or other agreed acceptance criteria, on the basis of specific quality levels as defined in EN 16296.All the imperfections that are not permissible shall be reported.5.5 Vis

33、ual examination of repaired weldsWhen a weld fails to comply wholly or in part with the applicable acceptance criteria and repair is necessary, the repaired weld shall be reexamined to the same requirements as the original weld.6 Test reportWhen test records are required, at least the following info

34、rmation shall be included in the report:a) name of the component manufacturer;b) name of the examining body, if different from the component manufacturer;5BS EN 131001:2017EN 131001:2017 (E)c) reference to this standard;d) location of the weld(s);e) the applicable acceptance criteria;f) type of mate

35、rial(s);g) material thickness;h) type of joint;i) welding process;j) extent of examination;k) examination devices used (if any);l) result of examination, with the detail of the imperfections exceeding the acceptance criteria and their location;m) name and signature of examiner and date of examinatio

36、n.If a permanent visual record of an examined weld is required, photographs or accurate sketches or both shall be made with any imperfections clearly indicated.6 BS EN 131001:2017EN 131001:2017 (E)Bibliography1 CEN/TS 16892, Plastics Welding of thermoplastics Specification of welding procedures2 EN

37、ISO 9712, Non-destructive testing Qualification and certification of NDT personnel (ISO 9712)7BS EN 131001:2017This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information

38、and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experie

39、nce and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Informa

40、tion on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, in

41、cluding British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in B

42、SI publicationsAll the content in BSI publications, including British Standards, is the property of and copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for com

43、mercial publication and use.Save for the provisions below, you may not transfer, share or disseminate any portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs pr

44、ior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standard purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the

45、sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printed for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be fu

46、rther reproduced in any format to create an additional copy. This includes scanning of the document.If you need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extract

47、sFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll

48、 have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standa

49、rds, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able

展开阅读全文
相关资源
  • BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdfBS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf
  • BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdfBS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf
  • BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdfBS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf
  • BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdfBS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf
  • BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdfBS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf
  • BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdfBS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf
  • BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdfBS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf
  • BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdfBS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf
  • BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdfBS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf
  • BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdfBS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > BS

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1