1、BRITISH STANDARD BS EN 13123-1:2001 Windows, doors and shutters Explosion resistance Requirements and classification Part 1: Shock tube The European Standard EN 13123-1:2001 has the status of a British Standard ICS 13.230; 91.060.50 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT
2、LAWBS EN 13123-1:2001 This British Standard, having been prepared under the direction of the Sector Committee for Building and Civil Engineering, was published under the authority of the Standards Committee and comes into effect on 15 June 2001 BSI 06-2001 ISBN 0 580 37704 0 National foreword This B
3、ritish Standard is the official English language version of EN 13123-1:2001. The UK participation in its preparation was entrusted by Technical Committee B/538, Doors, windows, shutters, hardware and curtain walling, to Subcommittee B/538/2, Doors, which has the responsibility to: A list of organiza
4、tions represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standar
5、ds Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard
6、 does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments an
7、d promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 12, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since
8、publication Amd. No. Date CommentsEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13123-1 April 2001 ICS 13.230; 91.060.50 English version Windows, doors and shutters Explosion resistance Requirements and classification Part 1: Shock tube Fentres, portes et fermetures Rsistance lexplosion Presc
9、riptions et classification Partie 1: Tube effet de souffle (shock tube) Fenster, Tren und Abschlsse Sprengwirkungshemmung Anforderungen und Klassifizierung Teil 1: Storohr This European Standard was approved by CEN on 7 March 2001. CEN members are bound to comply with the CEN/CENELEC Internal Regula
10、tions which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This Europ
11、ean Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the nationa
12、l standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMI
13、TEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13123-1:2001 EPage 2 EN 13123-1:2001 BSI 06-2001 Contents Page Foreword. 3 1 Scope . 4 2 Normative reference
14、s. 4 3 Terms and definitions 4 4 Requirements 4 5 Classification of the level of explosion pressure resistance (EPR) 5 Annex A (normative) Blast parameters and derivation. 7Page 3 EN 13123-1:2001 BSI 06-2001 Foreword This European Standard has been prepared by Technical Committee CEN/TC 33, Doors, w
15、indows, shutters, building hardware and curtain walling, the Secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2001, and conflicting national standards
16、 shall be withdrawn at the latest by October 2001. This European Standard is one of a series of standards for windows, doors and curtain walling. The requirements and classification relate to a test specified in EN 13124-1. Annex A is normative. According to the CEN/CENELEC Internal Regulations, the
17、 national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingd
18、om.Page 4 EN 13123-1:2001 BSI 06-2001 1 Scope This European Standard specifies the criteria which windows, doors and shutters shall satisfy to achieve a classification when submitted to the test method described in EN 13124-1. This European Standard concerns a method of test against blast waves gene
19、rated by using a shock tube facility to simulate a high explosive detonation in the order of 100 kg to 2 500 kg TNT at distances from about 35 m to 50 m. This European Standard is applicable to blast overpressure generated in a shock tube test facility used to simulate a high explosive detonation on
20、 windows, doors and shutters, complete with their frames and infills, for use in both internal and external locations in buildings. It gives no information on the explosion resistance capacity of the wall or other surrounding structure. 2 Normative references This European Standard incorporates by d
21、ated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standar
22、d only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 13124-1:2001, Windows, doors and shutters Explosion resistance Test method Part 1: Shock tube. 3 Terms and definitions For the purposes
23、 of this European Standard the terms and definitions given in EN 13124-1 apply. 4 Requirements Resistance to perforation and pressure shall be classified in accordance with clause 5. To achieve a particular class of explosion resistance, the test specimen shall: (a) be subjected to not less than the
24、 corresponding level of each of peak pressure, positive specific impulse and minimum duration specified in clause 5, Table 1; and (b) show no perforation or damage exceeding that specified in 9.2 of EN 13124-1:2001. After the test, the door leaf and/or any opening sash shall remain retained in the c
25、losed position whether the opening mechanisms shall be still operable or not. It shall not be possible to gain unauthorized access from the attack face as a result of damage or exposure during the test of any security closure mechanisms which were intentionally secure prior to the test. It is not a
26、requirement of the test that performance in other respects such as air permeability, watertightness, wind resistance, etc. be maintained.Page 5 EN 13123-1:2001 BSI 06-2001 If the intended application of the window, door and shutter is such that it will be specifically subjected to climatic extremes,
27、 the test specimen shall be tested at these climatic extremes. NOTE Care should be taken to ensure that all joints between the wall and the window or door have protection which is at least equal to that of the window or door. 5 Classification of the level of explosion pressure resistance (EPR) The c
28、lasses EPR1 to EPR4 given in Table 1 are in order of increasing explosion pressure resistance. When a window, door or shutter achieves a particular class it also automatically achieves all lower classes. Table 1 Characteristics of the shock wave Minimum values of: Classification code Peak pressure P
29、 max bar a Positive specific impulsion i + bar-ms EPR1 0,50 3,7 EPR2 1,00 9,0 EPR3 1,50 15,0 EPR4 2,00 22,0 aThe duration of the positive phase (t + ) shall be not less than 20 ms NOTE 1 The classification refers to the reflected pressure values which the test specimen experiences. NOTE 2 A latitude
30、 of -5 % is permitted on the pressure value to allow for gauge reading tolerance. No reduction is permitted on the impulse and duration values which shall be determined in accordance with annex A. The decay coefficient defining the shape of the mean pressure trace lies within the values 0 to 4. NOTE
31、 3 The testing authority is required to ensure that the pressure and impulse values for any one classification test remain below that of the next higher classification or, in the case of EPR4, the upper bound values given as P max= 2,5 and i += 32 (see Figure A.1 in annex A). NOTE 4 Results of the t
32、ests are further notated with an addition of an “S” or “NS” suffix with regard to the presence or absence of splinters originating from the rear (protected) face of the test specimen. Examples: EPR1 (S) = Splinters ejected from rear (protected side) of the glass or infill material. EPR1 (NS) = No sp
33、linters ejected from rear (protected side) of the glass or infill material.Page 6 EN 13123-1:2001 BSI 06-2001 Key 1 Time of arrival 2 Ambient pressure 3 Pressure 4 Positive specific impulse, i + 5 Positive phase 6 Duration 7 Negative specific impulse, i - 8 Negative phase 9 Time after explosion NOTE
34、 With a blast wave generated by a shock tube the negative phase may not be present. For definitions refer to clause 3. Figure 1 Idealized pressure-time variation for a blast wavePage 7 EN 13123-1:2001 BSI 06-2001 Annex A (normative) Blast parameters and derivation A.1 Scope This annex sets out the p
35、rocedures to be followed by the testing authority to achieve consistent measurement and derivation of the test blast parameters for comparison against the classification parameters defined in requirements and classification clause 5, Table 1. A.2 Symbols P(t) = Pressure, above ambient pressure, at t
36、ime t P c = Classification peak pressure P max = Peak pressure derived from measured test values i +c = Classification positive phase specific impulse i + = Positive phase specific impulse calculated from measured test values t +c = Classification positive phase duration t + = Positive phase duratio
37、n derived from measured test values t c = Triangular duration calculated from classification values of P cand i +c t = Triangular duration calculated from P maxand i + A.3 Units Parameter Units Equivalent units Pressure bar = 100 kPa - (kilopascal) = 100 kN/m 2 - (kilonewton/m 2 ) Duration ms = ms -
38、 (milliseconds) Impulse bar-ms = area enclosed by pressure-time curve A.4 Mathematical relationships The relationship between the parameters P max , i + , t +and t can be expressed as functions of the exponential decay shape of the idealized pressure-time trace using the following formulae:Page 8 EN
39、 13123-1:2001 BSI 06-2001 (a) The modified Friedlander equation: P(t) = P max 1 - t/t + exp-A t/t + ; where: A is the decay coefficient or form parameter. (b) The integration of the modified Friedlander equation to express the calculated impulse, which is the area under the positive phase of the pre
40、ssure-time trace, as: i += P max t + (1/A) - (1/A 2 ) 1 - exp(-A). (c) t = 2 i + /P max ; giving the equivalent triangular duration for the limiting case when the value of the decay coefficient, A, would be zero and the trace would be a straight line, which idealized case is often used in carrying o
41、ut response calculations. A.5 Classification blast pulses Figures A.1 and A.2 illustrate the idealized shape and relationships of the classification blast pulses which would occur with a value for the decay coefficient of A = 1. These values of P c(less than 5 %) and i +care the minimum permissible
42、to achieve the appropriate classification and are related to each other and t +cby the same formulae as in clause A.4: (a) P(t) = P c 1 - t/t +c exp-A t/t +c ; (b) i +c= P c t +c (1/A) - (1/A 2 ) 1 - exp(-A). Different shape classification pulses may similarly be derived ranging from sharper curves
43、having a steeper initial decay rate but longer final duration for A = 4 down towards the limiting case of a straight line corresponding to A = 0 when: (c) t +c= t c= 2 i +c /P c . In all cases, the values of all three blast parameters, peak pressure, impulse and duration and the value of the decay c
44、oefficient A shall comply with clause 5. It shall be noted that: (d) for example, when A is less than 1, the value for the impulse may have to be higher than the minimum classification value in order to comply with the requirement for the duration to be not less than 20 ms; (e) often the duration sh
45、all exceed 20 ms in order for the impulse not to be less than the classification minimum.Page 9 EN 13123-1:2001 BSI 06-2001 A.6 Method of recording test parameters The test blast parameters shall be obtained using electronic recording equipment capable of recording and reproducing, on screen and in
46、the form of a hard copy visual trace, the pressure- time history of the blast pulse in steps of not more than 0,1 ms. This shall be done for each of the two blast gauges receiving the blast pressure (normally the reflected values) experienced by the attack face of the test specimen. The pressure-tim
47、e history shall be recorded and reproducible over the positive phase period in detail and also over the subsequent period of not less than 10 times the duration of the positive phase. By agreement with the applicant, the equipment may incorporate devices to filter and/or smooth the pressure-time his
48、tory to a mean trace. If such devices are used, details of the method and effect of filtering or smoothing shall be stated in the test report. A.7 Criteria for compliance of the pressure wave A pressure wave in accordance with the classification will be achieved if the measured and calculated parame
49、ters are not less than the corresponding minimum values set out in clause 5, Table 1. The upper tolerance values for each class are imposed on the testing authority in order to ensure that test specimens are not subjected to unfairly over onerous or destructive loads. A.8 Procedure for verifying compliance of the pressure wave Measured and recorded pressure-time traces may follow an irregular shape, therefore it is necessary to carry out a recognized procedure, such as that
