1、BS EN 13461:2009ICS 55.120NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPackaging Cylindrical flexiblelaminated tubes Dimensions andtolerancesThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 April2009 BSI
2、 2009ISBN 978 0 580 58513 5Amendments/corrigenda issued since publicationDate CommentsBS EN 13461:2009National forewordThis British Standard is the UK implementation of EN 13461:2009. Itsupersedes BS EN 13461:2001 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalC
3、ommittee PKW/0/-/10, Plastics.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard
4、cannot confer immunityfrom legal obligations.BS EN 13461:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13461April 2009ICS 55.120 Supersedes EN 13461:2001 English VersionPackaging - Cylindrical flexible laminated tubes - Dimensionsand tolerancesEmballage - Tubes souples lamins cylindriques -D
5、imensions et tolrancesPackmittel - Zylindrische Laminattuben - Mae undToleranzenThis European Standard was approved by CEN on 21 February 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a nat
6、ional standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in a
7、ny other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Esto
8、nia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCH
9、ES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13461:2009: EBS EN 13461:2009EN 13461:2009 (E) 2 Contents Page Foreword . 3 1 Scope . 4 2 Terms and defini
10、tions 4 3 Dimensions . 5 Bibliography . 7 BS EN 13461:2009EN 13461:2009 (E) 3 Foreword This document (EN 13461:2009) has been prepared by Technical Committee CEN/TC 261 “Packaging”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, ei
11、ther by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by October 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN an
12、d/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13461:2001. It is based on the professional recommendations of the European Tube Manufacturers Association (ETMA). According to the CEN/CENELEC Internal Regulations, the national sta
13、ndards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
14、Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 13461:2009EN 13461:2009 (E) 4 1 Scope This document specifies sizes and geometric characteristics for cylindrical laminated flexible tubes which are produced by directly welding laminate materials. It app
15、lies to tubes used for packaging pharmaceutical, cosmetic and hygiene products, as well as for packaging food, industrial and domestic products. 2 Terms and definitions For the purposes of this standard, the following terms and definitions apply (see Figure 1). 2.1 nominal diameter, D conventional i
16、ndication utilized for the commercial description of the tube, which corresponds approximately to the outside diameter d1of the body of the tube 2.2 nominal length, L conventional indication utilized for the commercial description of the tube, corresponding approximately to the length l1: measured b
17、etween the shoulder and the open end of the tube NOTE The nominal length represents the length of the tube body (sleeve). 2.3 ovality diameter, d2diameter of the largest circle which can enclose the tube at any point along the body of the tube 2.4 wall thickness, S1thickness of the body wall of the
18、tube BS EN 13461:2009EN 13461:2009 (E) 5 Key 1 Shoulder 2 Nozzle 3 Orifice 4 Body (sleeve) B Measurement point for the length of the tube bodyFigure 1 Dimensions 3 Dimensions The dimensions of the tubes shall conform to Table 1. BS EN 13461:2009EN 13461:2009 (E) 6 Table 1 Dimensions Nominal diameter
19、 D mm Actual outside diameter1d1( 0,2) mm Nominal length L (+ 1,5/-2)2 mm Maximum ovality diameter d2 mm Wall thickness S1 ( 10%) rn 13,5 13,3 to 14 65 to 110 15,5 220 to 400 400 16 15,8 to 16,5 65 to 120 18 220 to 400 19 18,8 to 19,5 75 to 130 21 220 to 400 22 21,8 to 22,5 70 to 150 24,5 220 to 400
20、 25 24,8 to 25,5 90 to 160 27,5 220 to 400 28 27,8 to 28,5 100 to 185 31 220 to 400 30 29,6 to 30,5 120 to 195 33 220 to 400 32 31,8 to 32,5 120 to 200 35,5 220 to 400 35 34,6 to 35,5 90 to 200 38,5 220 to 400 38 38 204 42 220 to 400 40 39,6 to 40,5 120 to 200 44 220 to 400 50 49,6 to 50,5 120 to 20
21、0 55 220 to 400 1 Depending on the production machinery, the nominal diameter can vary within the limits of the given actual outside diameter. The actual outside diameter has a tolerance of 0,2 mm. 2 The actual length l1 should be within + 1,5 mm/-2 mm of the nominal length. BS EN 13461:2009EN 13461
22、:2009 (E) 7 Bibliography 1 EN 12374, Packaging Flexible tubes - Terminology BS EN13461:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishSta
23、ndards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant
24、aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0
25、)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Custom
26、er Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as Brit
27、ish Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details
28、on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits
29、 contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all B
30、SI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electroni
31、c, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email:
