1、BSI Standards PublicationBS EN 14399-1:2015High-strength structuralbolting assemblies forpreloadingPart 1: General requirementsBS EN 14399-1:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 14399-1:2015. It supersedes BS EN 14399-1:2005 which is withdrawn.Th
2、e UK participation in its preparation was entrusted to Technical Committee FME/9/-/2, Fasteners for structural bolting.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a cont
3、ract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 84412 6 ICS 21.060.01 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the a
4、uthority of the Standards Policy and Strategy Committee on 28 February 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 14399-1 February 2015 ICS 21.060.01 Supersedes EN 14399-1:2005English Version High-strength struc
5、tural bolting assemblies for preloading - Part 1: General requirements Boulonnerie de construction mtallique haute rsistance apte la prcontrainte - Partie 1: Exigences gnrales Hochfeste vorspannbare Garnituren fr Schraubverbindungen im Metallbau - Teil 1: Allgemeine Anforderungen This European Stand
6、ard was approved by CEN on 22 August 2014. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning s
7、uch national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its o
8、wn language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
9、 Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NOR
10、MUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14399-1:2015 EBS EN 14399-1:2015EN 14399-1:2015 (E) 2 Contents Page Foreword 3 Introduction .5 1 Scope 6 2 N
11、ormative references 6 3 Terms and definitions .7 4 Product characteristics .8 4.1 General 8 4.2 Type (bolting assemblies) .8 4.3 Property class (bolting assemblies) 9 4.4 Product grade (bolts, nuts, washers and, if provided, direct tension indicators) . 10 4.5 k-class and k-factor (bolting assemblie
12、s) . 11 5 Testing and assessment methods 11 5.1 General . 11 5.2 Type (bolting assemblies) 12 5.3 Property class (bolting assemblies) . 12 5.4 Product grade (bolts, nuts, washers and, if provided, direct tension indicators) . 13 5.5 k-class and k-factor (bolting assemblies) 15 6 Assessment and Verif
13、ication of Constancy of Performance (AVCP) 15 6.1 General . 15 6.2 Type testing . 16 6.3 Factory production control (FPC) . 17 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Regulation . 23 ZA.1 Scope and relevant characteristics 23
14、 ZA.2 Procedure for Assessment and Verification of Constancy of Performance (AVCP) of high-strength structural bolting assemblies for preloading . 24 ZA.3 CE marking and labelling . 28 Bibliography . 30 BS EN 14399-1:2015EN 14399-1:2015 (E) 3 Foreword This document (EN 14399-1:2015) has been prepare
15、d by Technical Committee CEN/TC 185 “Fasteners”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2015 and conflicting national standards shall be wi
16、thdrawn at the latest by November 2016. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14399-1:2005. In c
17、omparison with EN 14399-1:2005, the following modifications have been made: the standard was revised to meet the new format for harmonized standards and in relation to the Regulation (EU) No. 305/2011 (CPR); the requirements of this standard only relate to the product characteristics of bolting asse
18、mblies which are necessary for CE marking; all clauses dealing with further technical or other requirements have been transferred to EN 14399-2; the table containing the overview of the composition of bolting assemblies and component marking has been transferred to EN 14399-2. This document has been
19、 prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports basic work requirements of Regulation (EU) No. 305/2011. For relationship with Regulation (EU) No. 305/201, see informative Annex ZA, which is an integral part of this document. EN
20、 14399 consists of the following parts, under the general title High-strength structural bolting assemblies for preloading: Part 1: General requirements (the present document); Part 2: Suitability for preloading; Part 3: System HR Hexagon bolt and nut assemblies; Part 4: System HV Hexagon bolt and n
21、ut assemblies; Part 5: Plain washers; Part 6: Plain chamfered washers; Part 7: System HR Countersunk head bolt and nut assemblies; Part 8: System HV Hexagon fit bolt and nut assemblies; Part 9: System HR or HV Direct tension indicators for bolt and nut assemblies; Part 10: System HRC Bolt and nut as
22、semblies with calibrated preload. BS EN 14399-1:2015EN 14399-1:2015 (E) 4 According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Den
23、mark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 14399-1
24、:2015EN 14399-1:2015 (E) 5 Introduction This document on structural bolting assemblies reflects the situation in Europe where two technical solutions exist to achieve the necessary ductility of bolting assemblies. These solutions utilize different bolting assemblies (system HR, HV and HRC). Both sys
25、tems are well proven and it is the responsibility of the experts for structural connections whether they use the one or the other system. It is however important for the performance of the bolting assembly to avoid mixing up the components of both systems. Therefore, the bolts and nuts for both syst
26、ems are standardized in one single part of this European Standard each and the marking of the components of the same system is consistent. BS EN 14399-1:2015EN 14399-1:2015 (E) 6 1 Scope This European Standard specifies the general requirements for bolt/nut/washer(s) assemblies for high-strength str
27、uctural bolting, which are suitable for preloading. The intended use of bolting assemblies in accordance with this European Standard is structural metallic works. NOTE 1 High-strength structural bolting assemblies in accordance with EN 14399-2 to EN 14399-10 are designed to fulfil the requirements o
28、f this European Standard. NOTE 2 High-strength structural bolting assemblies are suitable for preloading in accordance with EN 1090-2 in steel structures. High-strength structural bolting assemblies smaller than M12 are not designed to be preloaded. High-strength structural bolting assemblies are no
29、t designed to be welded. Railway rail fasteners are not covered by this standard. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For unda
30、ted references, the latest edition of the referenced document (including any amendments) applies. EN 1090-2:2008+A1:2011, Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures EN 14399-2:2015, High-strength structural bolting assemblies for prel
31、oading - Part 2: Suitability for preloading EN 14399-3:2015, High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies EN 14399-4:2015, High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assembl
32、ies EN 14399-5, High-strength structural bolting assemblies for preloading - Part 5: Plain washers EN 14399-6, High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers EN 14399-7:2007, High-strength structural bolting assemblies for preloading - Part 7: System HR
33、- Countersunk head bolt and nut assemblies EN 14399-8:2007, High-strength structural bolting assemblies for preloading - Part 8: System HV - Hexagon fit bolt and nut assemblies EN 14399-9:2009, High-strength structural bolting assemblies for preloading - Part 9: System HR or HV - Direct tension indi
34、cators for bolt and nut assemblies EN 14399-10:2009, High-strength structural bolting assemblies for preloading - Part 10: System HRC - Bolt and nut assemblies with calibrated preload EN ISO 225, Fasteners - Bolts, screws, studs and nuts - Symbols and descriptions of dimensions (ISO 225) BS EN 14399
35、-1:2015EN 14399-1:2015 (E) 7 EN ISO 898-1:2013, Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) EN ISO 898-2:2012, Mechanical properties of fasteners made
36、of carbon steel and alloy steel - Part 2: Nuts with specified property classes - Coarse thread and fine pitch thread (ISO 898-2:2012) EN ISO 4759-1, Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts - Product grades A, B and C (ISO 4759-1) EN ISO 4759-3, Tolerances for fasteners - Par
37、t 3: Plain washers for bolts, screws and nuts - Products grades A and C (ISO 4759-3) EN ISO 6507-1, Metallic materials - Vickers hardness test - Part 1: Test method (ISO 6507-1) EN ISO 6508-1, Metallic materials - Rockwell hardness test - Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T)
38、(ISO 6508-1) EN ISO 10684, Fasteners - Hot dip galvanized coatings (ISO 10684) ISO 888, Fasteners - Bolts, screws and studs - Nominal lengths and thread lengths ISO 965-2, ISO general purpose metric screw threads - Tolerances - Part 2: Limits of sizes for general purpose external and internal screw
39、threads - Medium quality ISO 965-5, ISO general purpose metric screw threads - Tolerances - Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing 3 Terms and definitions For the purposes
40、of this document, the terms and definitions given in EN 1090-2:2008+A1:2011 and the following apply. 3.1 bolting assembly matching bolt, nut, washer(s) and if relevant, direct tension indicator and nut face washer or bolt face washer 3.2 single bolting assembly lot bolting assembly lot containing: b
41、olts from a single manufacturing lot; nuts from a single manufacturing lot; washers from a single manufacturing lot; and, if relevant: direct tension indicators from a single manufacturing lot; nut face washers from a single manufacturing lot; bolt face washers from a single manufacturing lot BS EN
42、14399-1:2015EN 14399-1:2015 (E) 8 3.3 extended bolting assembly lot bolting assembly lot containing: the component with the main influence on the result of the suitability test from a single manufacturing lot; the complementary components from several manufacturing lots Note 1 to entry: The componen
43、t having the main influence (either nut or direct tension indicator) is determined on the basis of test results. Note 2 to entry: An extended bolting assembly lot contains bolts, nuts and washers and, if relevant, direct tension indicators and nut face washers or bolt face washers. 3.4 manufacturing
44、 lot (for bolting assemblies components) quantity of components of a single designation including product grade, property class, type, and size, manufactured from bar, wire, rod or flat product from a single cast, processed through the same or similar steps at the same time or over a continuous time
45、 period, through the same heat treatment, coating and/or lubrication process, if any Note 1 to entry: Same process means: for a continuous process, the same treatment cycle without any setting modification; for a discontinuous process, the same treatment cycle for identical consecutive loads (batche
46、s). Note 2 to entry: The manufacturing lot may be split into a number of manufacturing batches for processing purposes and then re-assembled into the same manufacturing lot. 4 Product characteristics 4.1 General The performance of the high-strength structural bolting assemblies depends on the type o
47、f the bolting assemblies and on properties of their specific components (bolts, nuts, washers, and direct tension indicators if provided). Therefore, the requirements specified in 4.2 to 4.5 are assessed through the verification of the properties of the involved components and/or bolting assemblies,
48、 as applicable. 4.2 Type (bolting assemblies) 4.2.1 General Type covers the axial load expected from design and margin against overtightening. The Type is relevant for the ability of the bolting assembly to be tightened by different tightening methods given in EN 1090-2 in order to provide the decla
49、red performances of the bolting assemblies. There are two types of bolting assemblies: Type HR (systems HR with or without direct tension indicators, if provided, and HRC) designed to obtain ductility predominantly by plastic elongation of the bolt (minimum nut height 0,9 D and thread length of the bolt according to ISO 888); Type HV (system HV with or without direct tension indicators, if provided) designed to obtain ductility predominantly by plastic deformation of the engaged threads (nut height at approx
