1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationFibre-reinforced plastic composites Declaration of raw material characteristicsPart 1: General requirementsBS EN 16245-1:2013BS EN 16245-1:2013BS EN 16245-1:2013 BRITISH STANDARD
2、National forewordThis British Standard is the UK implementation of EN 16245-1:2013.The UK national committee is of the opinion that, in all parts of EN 16245, the use of the terms “guaranteed minimum value” and “guaranteed maximum value” is not appropriate within a voluntary-based standard. Furtherm
3、ore, the absolute “minimum value” and “maximum value” cannot be determined practicably, so that “statistical minimum value” (defined in EN 16245-1) and “statistical maximum value” (calculated in a similar manner using maximal values) are preferred.The UK participation in its preparation was entruste
4、d to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for i
5、ts correct application. The British Standards Institution 2013. Published by BSI Standards Limited 2013ISBN 978 0 580 74080 0ICS 83.120Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and
6、Strategy Committee on 30 June 2013.Amendments/corrigenda issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 16245-1 April 2013 ICS 83.120 English Version Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 1: General re
7、quirements Composites plastiques renforcs de fibres - Dclaration des caractristiques des matires premires - Partie 1: Exigences gnrales Faserverstrkte Verbundwerkstoffe - Angabe von Werkstoffeigenschaften - Teil 1: Allgemeine AnforderungenThis European Standard was approved by CEN on 1 March 2013. C
8、EN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on ap
9、plication to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
10、Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, L
11、atvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-
12、1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 16245-1:2013: EBS EN 16245-1:2013EN 16245-1:2013 (E)2Contents PageForeword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4 Content of a declaration
13、5 5 General information to be declared .6 5.1 General declaration .6 5.2 Documentation available at delivery7 5.3 Labelling .7 6 Certificate of Analysis (CoA) 7 Bibliography 9 BS EN 16245-1:2013EN 16245-1:2013 (E)2Contents PageForeword3 1 Scope 4 2 Normative references 4 3 Terms and definitions .4 4
14、 Content of a declaration5 5 General information to be declared .6 5.1 General declaration .6 5.2 Documentation available at delivery7 5.3 Labelling .7 6 Certificate of Analysis (CoA) 7 Bibliography 9 BS EN 16245-1:2013EN 16245-1:2013 (E)3ForewordThis document (EN 16245-1:2013) has been prepared by
15、Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN.This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2013, and conflicting national standards shall be withdra
16、wn at the latest by October 2013.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights.EN 16245 consists of the following parts, under the ge
17、neral title Fibre-reinforced plastic composites Declaration of raw material characteristics:Part 1: General requirementsPart 2: Specific requirements for resin, curing systems, additives and modifiersPart 3: Specific requirements for fibrePart 4: Specific requirements for fabricsPart 5: Specific req
18、uirements for core materialsAccording to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republ
19、ic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.BS EN 16245-1:2013EN 16245-1:2013 (E)41 ScopeThis European S
20、tandard specifies the minimum general information to be declared for materials to be used for manufacturing fibre-reinforced plastic composites products. This document includes requirements for the Certificate of Analysis (CoA). The purpose of the CoA is to verify that material properties and qualit
21、y conform to the declared values. This part of the standard is applicable to resins, curing systems, additives and modifiers, fibres, fabrics and core materials. The current version of the standard includes the following:the thermoset resins polyesters and vinyl esters;glass and carbon fibres;knitte
22、d/stitched fabrics;foam core and balsa core.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of t
23、he referenced document (including any amendments) applies.EN 16245-2, Fibre-reinforced plastic composites Declaration of raw material characteristics Part 2: Specific requirements for resin, curing systems, additives and modifiersEN 16245-3, Fibre-reinforced plastic composites Declaration of raw mat
24、erial characteristics Part 3: Specific requirements for fibreEN 16245-4, Fibre-reinforced plastic composites Declaration of raw material characteristics Part 4: Specific requirements for fabrics EN 16245-5, Fibre-reinforced plastic composites Declaration of raw material characteristics Part 5: Speci
25、fic requirements for core materialsISO 80000-1, Quantities and units Part 1: General3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.3.1mean valuesum of the (population or sample) data divided by the number of values used3.2guaranteed minimum or max
26、imum valuevalue guaranteed by the supplier, such as no single sample value is below or above the declared values, respectivelyBS EN 16245-1:2013EN 16245-1:2013 (E)41 ScopeThis European Standard specifies the minimum general information to be declared for materials to be used for manufacturing fibre-
27、reinforced plastic composites products. This document includes requirements for the Certificate of Analysis (CoA). The purpose of the CoA is to verify that material properties and quality conform to the declared values. This part of the standard is applicable to resins, curing systems, additives and
28、 modifiers, fibres, fabrics and core materials. The current version of the standard includes the following:the thermoset resins polyesters and vinyl esters;glass and carbon fibres;knitted/stitched fabrics;foam core and balsa core.2 Normative referencesThe following documents, in whole or in part, ar
29、e normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.EN 16245-2, Fibre-reinforced plastic composites Declarat
30、ion of raw material characteristics Part 2: Specific requirements for resin, curing systems, additives and modifiersEN 16245-3, Fibre-reinforced plastic composites Declaration of raw material characteristics Part 3: Specific requirements for fibreEN 16245-4, Fibre-reinforced plastic composites Decla
31、ration of raw material characteristics Part 4: Specific requirements for fabrics EN 16245-5, Fibre-reinforced plastic composites Declaration of raw material characteristics Part 5: Specific requirements for core materialsISO 80000-1, Quantities and units Part 1: General3 Terms and definitionsFor the
32、 purposes of this document, the following terms and definitions apply.3.1mean valuesum of the (population or sample) data divided by the number of values used3.2guaranteed minimum or maximum valuevalue guaranteed by the supplier, such as no single sample value is below or above the declared values,
33、respectivelyBS EN 16245-1:2013EN 16245-1:2013 (E)53.3manufacturerthe organisation which makes the material and/or the product in the form and condition in which it is delivered to the purchaser, either directly or through a supplierNote 1 to entry: If a supplier modifies a material from the original
34、 manufacturer, the new material is no longer in the responsibility of the original manufacturer, and the supplier is, according to this standard, the manufacturer of the material. Note 2 to entry: A manufacturer may also be a supplier, taking full responsibility of the original material.SOURCE: ISO
35、8591-1:1989, 2.1.93.4maximum valuevalue such that no single sample value is above the declared value3.5minimum valuevalue such that no single sample value is below the declared value3.6nominal valuesupplier defined value, typically defined by the mean value derived from a historical database of the
36、respective property3.7shelf lifeperiod of time after production during which a material or product that is kept under specified conditions retains its specified propertiesSOURCE: ISO 1382:2012, 23.8statistical minimum valuemean value minus two standard deviations of a historical population, i.e. the
37、re is 97,6 % probability that the test values are above this statistically defined minimum valueNote 1 to entry: This implies that all or part of the received material can have CoA values below the statistical minimum value declared by the manufacturer. In order to avoid this, the customer can inste
38、ad require guaranteed minimum value to be declared.3.9supplierorganisation or person that provides a productNote 1 to entry: Adapted from ISO 10006:2003.Note 2 to entry: The supplier may be different from the manufacturer. Note 3 to entry: It is the responsibility of the supplier to supply all requi
39、red documentation with the material.4 Content of a declarationA declaration shall consist of information according to Clause 5 of this part and Clause 5 of the respective parts of this standard.Upon request, the specific declared properties according to Parts 2 to 5 of this standard shall be documen
40、ted in a Certificate of Analysis (CoA).BS EN 16245-1:2013EN 16245-1:2013 (E)6The units used in a declaration shall be expressed in accordance with the International System of Units (SI),as specified in ISO 80000-1. Other units may be given, but only in addition to the SI units.If required informatio
41、n exists in other documents, specific reference to these documents and/or sections in these documents is accepted.Every page of a declaration document shall include the name and material number or code for identification of the material as used on the label, and shall be dated and numbered. The date
42、 indicated shall be the revision date of the material delivered. The page numbering system shall include the total number of pages or shall indicate the last page as such.The previous revision date as well as the latest revision date shall be posted on the first page of a declaration. The text of th
43、e declaration shall be written in a language acceptable to the recipient.5 General information to be declared5.1 General declarationThe following information shall be declared:a) reference to this part of EN 16245 (i.e. EN 16245-1);1) If the declaration deviates from this standard, these deviations
44、shall clearly be stated in the declaration.b) type of material (i.e. polyester resin, glass fibre, etc.);c) material number or material code:1) This section shall state the identification of the material as used on the label. Material number or material code shall be a unique designation which diffe
45、rentiates this material from any other material. There shall exist only one declaration (set of documents) to each identity or designation. 2) If a material formulation is changed so that any property or information in the original declaration is changed, the material and/or its declarations shall:i
46、) be given a new material number, code or name with a new relevant set of declaration documents; orii) be given a revision number or date that corresponds to the date of change in material formulation. 3) The brand name shall be stated.d) manufacturer; e) supplier (i.e. to be stated if different fro
47、m the manufacturer); f) location of manufacturing plant (i.e. valid for the manufacturer of the delivered material);g) shelf life; h) packaging information (i.e. packed for delivery);i) transportation and storage requirements.BS EN 16245-1:2013EN 16245-1:2013 (E)6The units used in a declaration shal
48、l be expressed in accordance with the International System of Units (SI),as specified in ISO 80000-1. Other units may be given, but only in addition to the SI units.If required information exists in other documents, specific reference to these documents and/or sections in these documents is accepted
49、.Every page of a declaration document shall include the name and material number or code for identification of the material as used on the label, and shall be dated and numbered. The date indicated shall be the revision date of the material delivered. The page numbering system shall include the total number of pages or shall indicate the last page as such.The previous revision date as well as the latest revision date shall be posted on the first page of a declaration. The text of the declaration shall be written in a l
