1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 170100:2001 The Eur
2、opean Standard EN 170100:2001 has the status of a British Standard ICS 31.140 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Harmonized system of quality assessment for electronic components Sectional specification: Waveguide type dielectric resonatorsThis British Standard, h
3、aving been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 21 September 2001 BSI 21 September 2001 ISBN 0 580 36509 3 BS EN 170100:2001 Amendments issued since publication A
4、md. No. Date Comments National foreword This British Standard is the official English language version of EN 170100:2001 published by the European Electronic Components Committee (CECC) of the European Committee for Electrotechnical Standardization (CENELEC). The UK participation in its preparation
5、was entrusted to Technical Committee EPL/49, Piezoelectric devices for frequency control and selection, which has the responsibility to: aid enquirers to understand the text; present to the responsible International/European committee any enquiries on the interpretation, or proposals for change, and
6、 keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European
7、publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary
8、 provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2
9、 to 19 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.EUROPEAN STANDARD EN 170100 NORME EUROPENNE EUROPISCHE NORM August 2001 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechn
10、ique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 170100:2001 E ICS 31.140 English version Sectional Specification
11、: Waveguide type dielectric resonators Spcification intermdiaire: Rsonateurs dilectriques modes guids Rahmenspezifikation: Dielektrische Resonatoren vom Wellenleitertyp This European Standard was approved by CENELEC on 2000-08-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Reg
12、ulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. T
13、his European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC memb
14、ers are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EN :0010711002 - - 2 Foreword This European Standard was
15、prepared by the Technical Committee CENELEC TC 49, Piezoelectric devices for frequency control and selection. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 170100 on 2000-08-01. The following dates were fixed: - latest date by which the EN h
16、as to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2002-02-01 - latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2003-08-01 Annexes designated “normative“ are part of the body of the standard.
17、In this standard, annexes A, B and C are normative. _ Page2 EN170100:2001 - - 3 E:001071 N1002 CONTENTS 1 Scope.4 2 General preferred ratings and guidance of detail specifications.4 2.1 Related documents 4 2.2 Preferred ratings and characteristics 4 2.3 Information to be prescribed in detail specifi
18、cations .4 3 Capability approval .5 3.1 Eligibility for capability approval5 3.2 Structural similarity.5 3.3 Procedures for capability approval5 3.4 Description of capability6 3.5 Capability Qualifying Components (CQCs7 3.6 Inspection requirements for CQCs.7 3.7 Programme for capability approval .8
19、3.8 Capability approval report.8 3.9 Abstract of description of capability 8 3.10 Modifications likely to affect capability approval .8 3.11 Initial capability approval.8 3.12 Maintenance of capability approval.14 3.13 Rework and repair work15 3.14 Quality conformance inspection15 3.15 Screening pro
20、cedures.16 4 Text and measurement procedures16 Annex A Example layout of an abstract of description of capability for inclusion in CECC 00 20017 Annex B Layout of the front page of a CQC specification for process control 18 Annex C Layout of the front page of a CQC specification to demonstrate a bou
21、ndary or limit .19 Page3 EN170100:2001 EN :0010711002 - - 4 1 Scope This sectional specification applies to waveguide type dielectric resonators as custom built products or as standard catalogue items whose quality is assessed on the basis of capability approval. It prescribes the preferred ratings
22、and characteristics with the appropriate tests and measuring methods contained in the generic specification EN 170000, and gives the general performance requirements to be used in detail specifications for waveguide type dielectric resonators. The concept of preferred values is in general directly a
23、pplicable to standard catalogue items but does not necessarily apply to custom built products. 2 General, preferred ratings and guidance on detail specifications 2.1 Related documents EN 60068-1 Environmental testing - Part 1: General and guidance (IEC 60068-1) EN 170000 Generic specification: Waveg
24、uide type dielectric resonators. CECC 00016 Basic requirements for the use of Statistical Process Control (SPC) in the CECC system. NOTE The above references apply to the current editions except for EN 60068-1 for which the referred edition and the applicable test clauses defined in EN 170000 shall
25、be used. 2.2 Preferred ratings and characteristics The values given in detail specifications shall preferably be selected from those stated in 2.4 of the generic specification EN 170000. 2.3 Information to be prescribed in detail specifications (for both custom built and standard catalogue items) Gu
26、idance on the preparation of detail specifications is given in the blank detail specification. Each detail specification shall state all the tests and measurements required for inspection. For standard catalogue items this shall, as a minimum, include the relevant tests given in the blank detail spe
27、cification, with methods and severities. The following information shall be given in each detail specification. 2.3.1 Outline drawing and dimensions The detail specification shall include a dimensional drawing of the waveguide type dielectric resonator and/or reference to an appropriate internationa
28、l standard, to permit easy recognition and to provide information for dimensioning and gauging procedures. The dimensions shall include the overall dimensions of the body of the component and the size and spacing of the terminations. All dimensions shall be stated in mm. Page4 EN170100:2001 - - 5 E:
29、001071 N1002 2.3.2 Marking The detail specification shall prescribe the content of the marking on the waveguide type dielectric resonator primary package in accordance with 2.5 of EN 170000. 2.3.3 Ordering information The detail specification shall prescribe that the following information is require
30、d when ordering a waveguide type dielectric resonator. a) Quantity b) Detail specification number, issue number and date and where applicable c) Nominal frequency in MHz or GHz d) Full description of any additional requirements to identify the waveguide type dielectric resonator. 2.3.4 Additional in
31、formation (not for inspection purposes) The detail specification may include information which is not normally required to be verified by the inspection procedure, such as circuit diagrams, curves, drawings and notes needed for clarification. 3 Capability approval 3.1 Eligibility for capability appr
32、oval Prior to making an application for capability approval a manufacturer shall first obtain manufacturers inspection approval in accordance with EN 100114-1. The primary stage of manufacture shall be as defined in 3.1 of the generic specification EN 170000. 3.2 Structural similarity Structural sim
33、ilarity is not applicable to Capability Approval. However, it is applicable to released lots as defined in 3.14.1 of this specification. 3.3 Procedures for capability approval 3.3.1 General Capability approval in waveguide type dielectric resonator technology covers: - the complete design, material
34、preparation and manufacturing techniques, including control procedures and tests; - the performance limits claimed for the processes and products, that is those specified for the Capability Qualifying Components (CQCs); - the range of mechanical structures for which approval is granted. Page5 EN1701
35、00:2001 EN :0010711002 - - 6 3.3.2 Application for capability approval In order to obtain capability approval the manufacturer shall apply the rules of procedure given in 2.4 of CECC 00 114-3. In an application for capability approval the manufacturer shall define the boundaries of the capability fo
36、r which approval is sought in accordance with 3.5. 3.3.3 Granting of capability approval Capability approval shall be granted when the manufacturer has: - prepared a capability manual describing the capability for which he wishes to be approved, to the satisfaction of the ONS; - agreed with the ONS
37、the range of CQCs, as defined in 2.7 of CECC 00 114-3, to be used for the assessment of capability; - successfully demonstrated that he can design and manufacture components which satisfy the requirements of this sectional specification, within the limits of his capability; - prepared a capability a
38、pproval test report to the satisfaction of the ONS. 3.4 Description of capability The manufacturer shall prepare a manual describing his capability (see 2.5 of CECC 00 114-3), in relation to the technologies involved. The manual shall be approved by the ONS who shall ensure that it is a true and com
39、plete record of procedures carried out by the manufacturer during the design, production, testing, inspection and release of his products. The manual is a document that shall be treated as commercial in confidence. The manual shall include the following as a minimum: - A general introduction and des
40、cription of the technologies involved; - Aspects of customer liaison including provision of design rules (if appropriate) and assistance to customers in the formulation of their requirements; - A detailed description of the design rules to be used; - The procedure for checking that the design rules
41、are complied with for waveguide type dielectric resonators manufactured to a detail specification; - A list of all materials used, with references to the corresponding purchasing specifications and goods inward inspection; - A flow chart for the total process showing quality control points and permi
42、tted rework loops and containing references to all process and quality control procedures which may invoke SPC procedures (see CECC 00 016); - A declaration of processes for which approval has been sought in accordance with 3.5.1; - A declaration of boundaries for which approval has been sought in a
43、ccordance with 3.5.2; - A list of CQCs used to assess the capability, with a general description of each, supported by a detailed table showing where the declared boundaries of capability are demonstrated by a particular CQC design; - A detail specification for each CQC. These shall be produced to t
44、he satisfaction of the ONS. (see annexes B and C). Page6 EN170100:2001 - - 7 E:001071 N1002 3.5 Capability Qualifying Components (CQCs) The manufacturer shall agree with the ONS the range of capability qualifying components, selected in accordance with the general plan (see 3.11.2) specified in the
45、capability manual. The CQCs shall comply with the following requirements: a) The range of CQCs used shall cover all the processes, component types and limits of the declared capability b) The CQCs shall be one of the following: - waveguide type dielectric resonators in production; - test pieces desi
46、gned for assessment of a process or range of processes; - a combination of both of these. When CQCs are designed and produced solely for capability approval, the manufacturer shall satisfy the ONS that the same design rules, materials and manufacturing processes will be applied to released products.
47、 The CQC specifications may refer to internal control documentation which specifies production testing and recording in order to demonstrate control and maintenance of processes and boundaries including the use of SPC procedures where appropriate. 3.5.1 Process The CQC specifications shall include t
48、he following processes to be assessed. This list is not exclusive: -Sintering see 3.11.3.1 - Deposition of electrodes (when applicable) see 3.11.3.2 3.5.2 Boundaries CQCs shall demonstrate a set of boundaries which shall include the following: - Temperature range see 3.11.4 (2) - Ageing limits (when
49、 claimed) see 3.11.4 (4) - Climatic category see 3.11.4 (2) - Mechanical test severities see 3.11.4 (2) This list is not exclusive. Where additional boundaries are claimed these shall be covered by one or more CQCs. 3.6 Inspection requirements for CQCs The inspection requirements shall be contained in the CQC detail specifications together with environmental tests, measurements, severities and end point limits, where appropriate (see 3.11). Where possible the tests applied to CQCs shall be selected from section 4 of the generic specification E
