1、BRITISH STANDARD BS EN 50289-3-17: 2002 Communication cables Specifications for test methods Part 3-17: Mechanical test methods Adhesion of dielectric and sheath The European Standard EN 50289-3-17:2002 has the status of a British Standard ICS 33.120.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PE
2、RMITTED BY COPYRIGHT LAWBS EN 50289-3-17:2002 This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 18 April 2002 BSI 18 April 2002 ISBN 0 580 3
3、9592 8 National foreword This British Standard is the official English language version of EN 50289-3-17:2002. The UK participation in its preparation was entrusted to Technical Committee EPL/46, Cables, wires and waveguides, RF connectors and accessories for communication and signalling, which has
4、the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under th
5、e section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applic
6、ation. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related i
7、nternational and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document w
8、as last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 50289-3-17 NORME EUROPENNE EUROPISCHE NORM March 2002 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnisch
9、e Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2002 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 50289-3-17:2002 E ICS 33.120.10 English version Communication cables Specifications for test methods Part 3-
10、17: Mechanical test methods Adhesion of dielectric and sheath Cbles de communication Spcifications des mthodes dessai Partie 3-17: Mthodes dessais mcaniques Adhrence du dilectrique et de la gaine Kommunikationskabel Spezifikationen fr Prfverfahren Teil 3-17: Mechanische Prfverfahren - Haftung von Di
11、elektrikum und Mantel This European Standard was approved by CENELEC on 2001-11-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date list
12、s and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the re
13、sponsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland,
14、Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EN 50289-3-17:2002 - 2 - Foreword This European Standard was prepared by SC 46XC, Multicore, Multipair and Quad Data communication cables, of the Technical Committee CENELEC TC 46X, Communication C
15、ables. The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 50289-3-17 on 2001-11-01. The following dates were fixed: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endor
16、sement (dop) 2002-11-01 - latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2004-11-01 This European Standard has been prepared under the European Mandate M/212 given to CENELEC by the European Commission and the European Free Trade Association.- 3 - EN 5
17、0289-3-17:2002 Contents 1 Scope.4 2 Normative references 4 3 Definitions . 4 4 Method. 4 4.1 Preparation of test specimens 4 4.2 Procedure 4 4.3 Expression of results . 4 5 Requirements 5 6 Details to be specified. 5 7 Test report. 5EN 50289-3-17:2002 - 4 - 1 Scope This Part 3-17 of EN 50289 details
18、 the method of test to determine the adhesion of the dielectric and of the sheath of coaxial cables used in analogue and digital communication systems. It is to be read in conjunction with Part 3-1 of EN 50289, which contains essential provisions for its application. 2 Normative references This Euro
19、pean Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications
20、 apply to this European Standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies (including amendments). EN 50289-3-1 2001 Communication cables - Specifications for tests methods Part 3-1: Mechanical test method
21、s General requirements EN 50290-1-2 1) - Communication cables - Part 1-2: Definitions 3 Definitions For the purposes of this European Standard, the definitions of EN 50290-1-2 apply. 4 Method 4.1 Preparation of test specimens Two test specimens separated by at least 300 mm shall be cut from the fini
22、shed cable, unless otherwise specified in the relevant cable specification. Each test specimen shall be prepared as shown in Figure 1. Stripping shall be done carefully so as not to effect the adhesion of the test sample. The inner conductor shall be sufficiently long to be gripped by the jaw of a t
23、ensile testing device. 4.2 Procedure The test piece shall be loaded into the tensile testing machine and test fixture as shown in Figure 2. The diameter of the hole in the test plate shall be larger than the diameter of the centre conductor or the dielectric by 0,10 0,03 mm. The inner conductor shal
24、l be pulled steadily at a rate not exceeding 100 mm/min until the dielectric or the outer conductor and sheath is/are completely removed. Sudden pulls and jerking shall be avoided. The physical handling of the test specimens shall be kept to a minimum to avoid specimen deterioration. 4.3 Expression
25、of results Dielectric adhesion shall be defined as the highest tensile reading obtained when the conductor to dielectric bond is broken.1)At draft stage.- 5 - EN 50289-3-17:2002 5 Requirements The value of the adhesion and the lengths of the dielectric shall be in accordance with the values stated i
26、n the relevant cable specification. The conductor surface must be exempt from any remaining insulating material. 6 Details to be specified The detail specification shall include: - the temperature; - the value of the adhesion; - the lengths of the dielectric. 7 Test report The test report shall incl
27、ude: - temperature; - the lengths of the dielectric, - the value of the adhesion, - pass/fail criteria.EN 50289-3-17:2002 - 6 - 2 mm Dielectric Inner conductor Outer conductor and sheath 2 mm Figure 1 Dimension of stripping Holed plate Dielectric Outer Conductor Holes plate Outer conductor and sheat
28、h Tensile load Tensile load Tensile grip Tensile grip Figure 2 Test equipmentblankBS EN 50289-3-17:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in
29、 Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our
30、products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 74
31、00. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996
32、 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise reque
33、sted. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and service
34、s. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Mem
35、bership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Cop
36、yright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted
37、 in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.
