1、BRITISH STANDARD BS EN 50289-3-5:2001 Communication cables Specifications for test methods Part 3-5: Mechanical test methods Crush resistance of the cable The European Standard EN 50289-3-5:2001 has the status of a British Standard ICS 33.120.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED
2、BY COPYRIGHT LAWBS EN 50289-3-5:2001 This British Standard, having been prepared under the direction of the Electrotechnical Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 13 November 2001 BSI 13 November 2001 ISBN 0 580 3868
3、8 0 National foreword This British Standard is the official English language version of EN 50289-3-5:2001. The UK participation in its preparation was entrusted by Technical Committee EPL/46, Cables, wire and waveguides, RF connectors, and accessories for communication and signalling, to Subcommitte
4、e EPL/46/1, Communication cables, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be f
5、ound in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standa
6、rds are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep
7、the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover. The BSI copyright date displayed in
8、 this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 50289-3-5 NORME EUROPENNE EUROPISCHE NORM August 2001 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechn
9、ique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2001 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 50289-3-5:2001 E ICS 33.120.10 English version Communication cab
10、les - Specifications for test methods Part 3-5: Mechanical test methods - Crush resistance of the cable Cbles de communication - Spcifications des mthodes dessai Partie 3-5: Mthodes dessais mcaniques - Rsistance lcrasement du cble Kommunikationskabel - Spezifikationen fr Prfverfahren Teil 3-5: Mecha
11、nische Prfverfahren - Querdruckbestndigkeit des Kabels This European Standard was approved by CENELEC on 2001-05-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard withou
12、t any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language
13、 made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Ge
14、rmany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EN 50289-3-5:2001 - 2 - Foreword This European Standard was prepared by the Technical Committee CENELEC TC 46X, Communication cables. The text of the draft was submitted t
15、o the formal vote and was approved by CENELEC as EN 50289-3-5 on 2001-05-01. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2002-04-01 latest date by which the national stand
16、ards conflicting with the EN have to be withdrawn (dow) 2004-04-01 This European Standard has been prepared under the European Mandate M/212 given to CENELEC by the European Commission and the European Free Trade Association.- 3 - EN50289-3-5:2001 Contents 1 Scope 4 2 Normative references 4 3 Defini
17、tions . 4 4 Test method. 4 4.1 Equipment. 4 4.2 Test sample. 4 4.3 Procedure 5 4.4 Requirements 5 4.4.1 Coaxial cables 5 4.4.2 Symmetrical cables. 5 4.4.3 Optical cables. 6 5 Test report . 6EN 50289-3-5:2001 - 4 - 1 Scope This Part 3-5 of EN 50289 details the method of test to determine the crush re
18、sistance of the cable used in analogue and digital communication systems. It is to be read in conjunction with Part 3-1 of EN 50289, which contains essential provisions for its application. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from othe
19、r publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or
20、revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 50289-3-1 2001 Communication cables - Specifications for test methods - Part 3-1: Mechanical test methods - General requirements EN 50290-1- 2 1) Communication cables - Part 1-2: Def
21、initions 3 Definitions For the purposes of this European Standard the definitions of EN 50290-1-2 apply. 4 Test method 4.1 Equipment The apparatus shall allow a sample of cable to be crushed between a flat steel base plate and a movable steel plate which applies the crushing force uniformly over a 1
22、00 mm length of the sample. The edges of the movable plate shall be rounded with a radius of about 5 mm. They are not included in the 100 mm flat part of this plate. A suitable apparatus is shown in Figure 1. 4.2 Test sample The sample shall be of a length sufficient to carry out the test specified.
23、 For small cables (less than 5 mm outer diameter) the cables may be tested forming a loop (top of Figure 1) in this case the force to be applied is twice the specified force. The radius of the loop shall be large enough not to affect the transmission characteristics of the cable.1)At draft stage.- 5
24、 - EN50289-3-5:2001 4.3 Procedure The cable sample shall be mounted on the base plate of the test apparatus so that lateral movement is prevented. The cable specimen is compressed by a parallel flat movable steel plate with rounded edges applying a load (see Figure 1). The load (F) as indicated in t
25、he relevant cable specification shall be applied gradually without any abrupt change for a duration of 2 minutes. If incremental loading is used the steps shall not exceed a ratio of 1,5 :1 If requested in the relevant specification, an additional or alternative test may be performed by inserting on
26、e or more steel mandrels (25 mm in diameter unless otherwise specified in the detail specification) perpendicular to the sample, to represent particular operational conditions. Figure 1 - Crushing test 4.4 Requirements 4.4.1 Coaxial cables After the load has been removed the magnitude of the impedan
27、ce irregularity introduced by the test shall be measured by a pulse or TDR method. After the test, the reflection characteristics shall be within the limiting values specified in the detail specification. 4.4.2 Symmetrical cables After the test, the transmission characteristics shall be within the l
28、imiting values specified in the relevant specification.EN 50289-3-5:2001 - 6 - 4.4.3 Optical cables After the test, the transmission characteristics shall be within the limiting values specified in the relevant specification. 5 Test report The test report shall include: - value of the force F, - dis
29、tance of the crushed region to the end of the sample, - electrical /optical tests and their requirements, - number of tests performed, - temperature, - sample length, - pass/fail criteria.blankBS EN 50289-3-5:2001 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the
30、independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure tha
31、t they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible,
32、the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, internationa
33、l and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those th
34、at have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services ar
35、e also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details o
36、f these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of
37、 the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission fro
38、m BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.
