BS EN 60335-2-99-2003 Specification for safety of household and similar electrical appliances - Particular requirements for commercial electric hoods《家用和类似用途电器的安全规范 商用电炉罩的特殊要求》.pdf

上传人:medalangle361 文档编号:575600 上传时间:2018-12-13 格式:PDF 页数:18 大小:394.87KB
下载 相关 举报
BS EN 60335-2-99-2003 Specification for safety of household and similar electrical appliances - Particular requirements for commercial electric hoods《家用和类似用途电器的安全规范 商用电炉罩的特殊要求》.pdf_第1页
第1页 / 共18页
BS EN 60335-2-99-2003 Specification for safety of household and similar electrical appliances - Particular requirements for commercial electric hoods《家用和类似用途电器的安全规范 商用电炉罩的特殊要求》.pdf_第2页
第2页 / 共18页
BS EN 60335-2-99-2003 Specification for safety of household and similar electrical appliances - Particular requirements for commercial electric hoods《家用和类似用途电器的安全规范 商用电炉罩的特殊要求》.pdf_第3页
第3页 / 共18页
BS EN 60335-2-99-2003 Specification for safety of household and similar electrical appliances - Particular requirements for commercial electric hoods《家用和类似用途电器的安全规范 商用电炉罩的特殊要求》.pdf_第4页
第4页 / 共18页
BS EN 60335-2-99-2003 Specification for safety of household and similar electrical appliances - Particular requirements for commercial electric hoods《家用和类似用途电器的安全规范 商用电炉罩的特殊要求》.pdf_第5页
第5页 / 共18页
亲,该文档总共18页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、BRITISH STANDARD BS EN 60335-2-99:2003 Household and similar electrical appliances Safety Part 2-99: Particular requirements for commercial electric hoods The European Standard EN 60335-2-99:2003 has the status of a British Standard ICS 97.040.20 BS EN 60335-2-99:2003 This British Standard was publi

2、shed under the authority of the Standards Policy and Strategy Committee on 4 November 2003 BSI 4 November 2003ISBN 0 580 42813 3 National foreword This British Standard is the official English language version of EN 60335-2-99:2003. It is identical with IEC 60335-2-99:2003. The UK participation in i

3、ts preparation was entrusted by Technical Committee CPL/61, Safety of household electrical appliances, to Subcommittee CPL/61/5, Commercial catering equipment, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross

4、-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of B

5、ritish Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; pre

6、sent to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front

7、cover, the EN title page, pages 2 to 15 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsEUROPEAN STANDARD EN 60335-2-99 NORME EUROPENNE EUROPISCHE NORM September 2003 CENELEC

8、European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2003 CENELEC - All rights of exploitation in any form and by any means reserved worldwid

9、e for CENELEC members. Ref. No. EN 60335-2-99:2003 E ICS 97.040.20 English version Household and similar electrical appliances Safety Part 2-99: Particular requirements for commercial electric hoods (IEC 60335-2-99:2003) Appareils lectrodomestiques et analogues Scurit Partie 2-99: Rgles particulires

10、 pour les hottes de cuisine lectriques usage commercial (CEI 60335-2-99:2003) Sicherheit elektrischer Gerte fr den Hausgebrauch und hnliche Zwecke Teil 2-99: Besondere Anforderungen fr elektrische Dunstabzugshauben fr den gewerblichen Gebrauch (IEC 60335-2-99:2003) This European Standard was approve

11、d by CENELEC on 2003-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationa

12、l standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language a

13、nd notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Lithuania, Luxembourg, Malta, Netherland

14、s, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. -53306 NE-23002:99 - - 2 Foreword The text of document 61E/422/FDIS, future first edition of IEC 60335-2-99, prepared by SC 61E of the IEC Technical Committee 61, Safety of household and similar electrical appliances, was

15、submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60335-2-99 on 2003-07-01. The following dates are applicable: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2004-04-01 - date

16、on which national standards conflicting with the EN have to be withdrawn (dow) 2006-07-01 This part 2 has to be used in conjunction with EN 60335-1, Household and similar electrical appliances Safety Part 1: General requirements. It was established on the basis of the 2002 edition of that standard.

17、Amendments and revisions of Part 1 have also to be taken into account and the dates when such changes become applicable will be stated in the relevant amendment or revision of Part 1. This part 2 supplements or modifies the corresponding clauses of EN 60335-1, so as to convert it into the European S

18、tandard: Safety requirements for commercial electric hoods. When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies as far as is reasonable. When this standard states “addition“, “modification“ or “replacement“, the relevant text of Part 1 is to be adapted accor

19、dingly. NOTE 1 The following numbering system is used: - subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1; - unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including those in a replaced clause o

20、r subclause; - additional annexes are lettered AA, BB, etc.; - subclauses, notes and annexes that are additional to those in the IEC standard are prefixed with the letter Z. NOTE 2 The following print types are used: - requirements: in roman type; - test specifications: in italic type; - notes: in s

21、mall roman type. Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the associated noun are also in bold. There are no special national conditions causing a deviation from this European Standard, other than those listed in Annex ZA to EN 603

22、35-1. There are no national deviations from this European Standard, other than those listed in Annex ZB to EN 60335-1. p NOTE In this document, p is used in the margin to indicate instructions for preparing the printed version. _ 2egaP 3002:99253306NESBPage2 EN60335299:2003 - 3 - -53306 NE-23002:99

23、Introduction p Add: An investigation by CENELEC TC 61 has shown that all risks from products within the scope of this standard are fully covered by the Low Voltage Directive, 73/23/EEC. For products having mechanical moving parts, a risk assessment in accordance with the Machinery Directive, 98/37/E

24、C, has shown that the risks are mainly of electrical origin and consequently this directive is not applicable. However, the relevant essential safety requirements of the Machinery Directive are covered by this standard together with the principal objectives of the Low Voltage Directive. _ Endorsemen

25、t notice The text of the International Standard IEC 60335-2-99:2003 was approved by CENELEC as a European Standard without any modification. _ 3egaP 3002:99253306NESBPage3 EN60335299:2003 CONTENTS INTRODUCTION.5 1 Scope.6 2 Normative references.6 3 Definitions6 4 General requirement.7 5 General cond

26、itions for the tests 7 6 Classification7 7 Marking and instructions.7 8 Protection against access to live parts8 9 Starting of motor-operated appliances 8 10 Power input and current .9 11 Heating9 12 Void .10 13 Leakage current and electric strength at operating temperature10 14 Transient overvoltag

27、es .10 15 Moisture resistance10 16 Leakage current and electric strength.10 17 Overload protection of transformers and associated circuits .10 18 Endurance10 19 Abnormal operation11 20 Stability and mechanical hazards .11 21 Mechanical strength .11 22 Construction.11 23 Internal wiring.12 24 Compone

28、nts.12 25 Supply connection and external flexible cords 12 26 Terminals for external conductors.13 27 Provision for earthing .13 28 Screws and connections.13 29 Clearances, creeping distances and solid insulation .14 30 Resistance to heat and fire.14 31 Resistance to rusting14 32 Radiation, toxicity

29、 and similar hazards14 Annexes .15 Annex N (normative) Proof tracking test.15 Bibliography15 4egaP 3002:99253306NESBPage4 EN60335299:2003 INTRODUCTION It has been assumed in the drafting of this international standard that the execution of its provisions is entrusted to appropriately qualified and e

30、xperienced persons. This standard recognizes the internationally accepted level of protection against hazards such as electrical, mechanical, thermal, fire and radiation of appliances when operated as in normal use taking into account the manufacturers instructions. It also covers abnormal situation

31、s that can be expected in practice. This standard takes into account the requirements of IEC 60364 as far as possible so that there is compatibility with the wiring rules when the appliance is connected to the supply mains. However, national wiring rules may differ. If an appliance within the scope

32、of this standard also incorporates functions that are covered by another part 2 of IEC 60335, the relevant part 2 is applied to each function separately, as far as is reasonable. If applicable, the influence of one function on the other is taken into account. This standard is a product family standa

33、rd dealing with the safety of appliances and takes precedence over horizontal and generic standards covering the same subject. An appliance that complies with the text of this standard will not necessarily be considered to comply with the safety principles of the standard if, when examined and teste

34、d, it is found to have other features that impair the level of safety covered by these requirements. An appliance employing materials or having forms of construction differing from those detailed in the requirements of this standard may be examined and tested according to the intent of the requireme

35、nts and, if found to be substantially equivalent, may be considered to comply with the standard. 5egaP 3002:99253306NESBPage5 EN60335299:2003 HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES SAFETY Part 2-99: Particular requirements for commercial electric hoods 1 Scope This clause of Part 1 is replaced

36、by the following. This International Standard deals with the safety of electrically operated commercial hoods intended for installation above commercial cooking appliances such as ranges, griddles, griddle grills and deep fat fryers, and not intended for household use, their rated voltage being not

37、more than 250 V for single phase hoods connected between one phase and neutral, and 480 V for other hoods. Only single complete units and hoods supplied as separate parts which when assembled form a complete working hood, incorporating a fan, are within the scope of the standard. NOTE 101 Hoods are

38、used, for example in restaurants, canteens, hospitals and commercial enterprises such as bakeries, butcheries, etc. The hood may be used above one or more appliance of the same or different types. So far as is practicable, this standard deals with the common hazards presented by these types of appli

39、ances. NOTE 102 Attention is drawn to the fact that: for hoods intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary; in many countries additional requirements including ventilation requirements are specified by the national health authorities, the n

40、ational authorities responsible for the protection of labour and similar authorities; NOTE 103 This standard does not apply to: domestic range hoods (IEC 60335-2-31); purpose-built hoods, although this standard can be used as a guide (a purpose-built hood is either constructed on-site or specially c

41、onstructed in the factory and is not mass produced); hoods not incorporating a fan; hoods designed exclusively for industrial purposes; hoods intended to be used in locations where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas). NOTE 104

42、 Requirements for hoods with externally mounted fans are under consideration. 2 Normative references This clause of Part 1 is applicable. 3 Definitions This clause of Part 1 is applicable except as follows. 3.1.4 Addition: NOTE 101 The rated power input is the sum of the power inputs of all the indi

43、vidual elements in the hood which can be on at one time; where several such combinations are possible, that giving the highest power input is used in determining the rated power input. 6egaP 3002:99253306NESBPage6 EN60335299:2003 3.1.9 Replacement: normal operation operation of the appliance under t

44、he following conditions The hood is operated after installation in accordance with the instructions, except that it is not connected to a duct. 3.101 hood motor-operated appliance intended to collect contaminated air from above cooking ranges, hobs and similar cooking appliances. NOTE 1 The contamin

45、ated air may pass through a filter and be discharged back into the room or removed from the room. NOTE 2 The cooking appliances may be supplied by electricity or fuels such as gas. 4 General requirement This clause of Part 1 is applicable. 5 General conditions for the tests This clause of Part 1 is

46、applicable. 6 Classification This clause of Part 1 is applicable except as follows. 6.1 Replacement: Hoods shall be class I with respect to protection against electric shock. Compliance is checked by inspection and by the relevant tests. 7 Marking and instructions This clause of Part 1 is applicable

47、 except as follows. 7.1 Addition: Hoods shall be marked on or near the lampholder with the maximum power input of replaceable illumination lamps as follows: lamp max. W or max.W 7.6 Addition: Add the following symbol: symbol 5021 of IEC 60417-1 equipotentiality 7egaP 3002:99253306NESBPage7 EN6033529

48、9:2003 7.12 Addition: The instructions for use shall state the substance of the following: there shall be adequate air intake into the room when the hood is used at the same time as appliances burning gas or other fuels; the details concerning the method and frequency of cleaning and that filters mu

49、st be cleaned regularly; there is a fire risk if cleaning is not carried out in accordance with the instructions; do not flamb under the hood. If Symbol 5021 of IEC 60417-1 is marked on the hood, its meaning shall be explained. 7.12.1 Replacement: The hood shall be accompanied by instructions detailing any special precautions necessary for installation. The i

展开阅读全文
相关资源
  • BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdfBS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf
  • BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdfBS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf
  • BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdfBS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf
  • BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdfBS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf
  • BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdfBS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf
  • BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdfBS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf
  • BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdfBS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf
  • BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdfBS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf
  • BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdfBS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf
  • BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdfBS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > BS

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1