1、BRITISH STANDARD BS EN 60512-1-4:1997 IEC 60512-1-4: 1997 Incorporating Corrigendum No. 1 Electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 1: General Section 4: Test 1d. Contact protection effectiveness (scoop-proof) The European Standard EN 6
2、0512-1-4:1997 has the status of a British Standard ICS 31.220.01 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS EN 60512-1-4:1997 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the S
3、tandards Board and comes into effect on 15 December 1997 BSI 12 February 2002 ISBN 0 580 28736 X National foreword This British Standard is the English language version of EN 60512-1-4:1997. It is identical with IEC 60512-1-4:1997 including corrigendum November 2000. The UK participation in its prep
4、aration was entrusted by Technical Committee EPL/48, Electromechanical components for electronic equipment, to Subcommittee EPL/48/2, Connectors for electronic equipment, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committe
5、e any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 Janu
6、ary 1997, all IEC publications have the number 60000 added to the old number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references The Br
7、itish Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A Brit
8、ish Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a fron
9、t cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 7 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments 13227 Corrigendum No.1 12 February 2002 Replac
10、ement of Figure 2BS EN 60512-1-4:1997 BSI 12 February 2002 i Contents Page National foreword Inside front cover Foreword 2 Text of EN 60512-1-4 3ii blankEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 60512-1-4 October 1997 ICS 31.220.01 English version Electromechanical components for electron
11、ic equipment Basic testing procedures and measuring methods Part 1: General Section 4: Test 1d: Contact protection effectiveness (scoop-proof) (IEC 60512-1-4:1997) Composants lectromcaniques pour quipements lectroniques Procdures dessai de base et mthodes de mesure Partie 1: Gnralits Section 4: Essa
12、i 1d: Efficacit de la protection des contacts (scoop-proof) (CEI 60512-1-4:1997) Elektrisch-mechanische Bauelemente fr elektronische Einrichtungen Me- und Prfverfahren Teil 1: Allgemeines Hauptabschnitt 4: Prfung 1d: Wirksamkeit des Kontaktschutzes (Scoop-proof) (IEC 60512-1-4:1997) This European St
13、andard was approved by CENELEC on 1997-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references conce
14、rning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into
15、its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spai
16、n, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1997 CENELEC All rights of exploitation
17、 in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-1-4:1997 EEN 60512-1-4:1997 BSI 12 February 2002 2 Foreword The text of document 48B/598/FDIS, future edition 1 of IEC 60512-1-4, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mec
18、hanical structures for electronic equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60512-1-4 on 1997-10-01. The following dates were fixed: Annexes designated “normative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex Z
19、A has been added by CENELEC. Endorsement notice The text of the International Standard IEC 60512-1-4:1997 was approved by CENELEC as a European Standard without any modification. Contents Page Foreword 2 1 Scope and object 3 2 Normative reference 3 3 Preparation of specimens 3 4 Test methods 3 5 Req
20、uirements 5 6 Details to be specified 5 Annex ZA (normative) Normative references to international publications with their corresponding European publications Inside back cover Figure 1 Method A: Example with cylindrical connector 4 Figure 2 Method B: Free connector with male contacts coupled to fix
21、ed connector with male contacts 5 latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1998-07-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1998-07-01EN 60512-
22、1-4:1997 BSI 12 February 2002 3 1 Scope and object This section of IEC 60512-1 is to be used when referenced by the detail specification to test mechanical components overseen by the IEC subcommittee 48B. This test can also be done on similar devices when the detail specification so prescribes. The
23、object of this test is to define a standard test method to verify the ability of a connector to prevent the accidental touching of its contact by the front of the mating connector. It is primarily intended to be applied to cylindrical multi-contact connectors which are required to be scoop-proof. 2
24、Normative reference The following normative document contains provisions which, through reference in this text, constitute provisions of this section of IEC 60512-1. At the time of publication, the edition indicated was valid. All normative documents are subject to revision, and parties to agreement
25、s based on this section of IEC 60512-1 are encouraged to investigate the possibility of applying the most recent edition of the normative document indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. IEC 60512-2:1985, Electromechanical components for
26、 electronic equipment Basic testing procedures and measuring methods Part 2: General examination, electrical continuity and contact resistance tests, insulation tests and voltage stress tests 3 Preparation of specimens The connectors shall be fitted with their full set of contacts. They shall be wir
27、ed as specified by the detail specification. 4 Test methods 4.1 Procedure A suitable device for detecting electrical continuity, such as an ohmmeter, shall be connected between the housing (shell) of the free connector and all of the contacts in the fixed connector wired together.EN 60512-1-4:1997 4
28、 BSI 12 February 2002 4.2 Method A While attempting to mismate the free connector, fitted with female contacts to the fixed connector fitted with male contacts, at various angles and rotations as illustrated in Figure 1, any evidence of electrical continuity shall be noted. The test is then repeated
29、 on a set of connectors with the free connector fitted with male contacts and the fixed connector fitted with female contacts. Figure 1 Method A: Example with cylindrical connectorEN 60512-1-4:1997 BSI 12 February 2002 5 4.3 Method B The free connector fitted with male contacts is coupled with the f
30、ixed connector fitted also with male contacts (see Figure 2). The connectors shall be subjected to the test 4a, voltage proof test, in accordance with IEC 60512-2 60512-4-1 1)at the specified test voltage. The voltage shall be applied between each group of contacts, one group consisting of all conta
31、cts in the free connector connected together, the second with all the contacts in the fixed connector connected together. 5 Requirements 5.1 Method A During the attempted mismating, there shall be no evidence of electrical continuity between the housing (metal shell) and the male contacts. 5.2 Metho
32、d B No breakdown or flashover shall be observed. 6 Details to be specified When this test is required by the detail specification, the following details shall be specified: a) preparation of the specimen including details of the wiring; b) test voltage for method B; c) any deviation from the standar
33、d test method. 1) Publication number of the future edition. Figure 2 Method B: Free connector with male contacts coupled to fixed connector with male contacts6 blankEN 60512-1-4:1997 BSI 12 February 2002 7 Annex ZA (normative) Normative references to international publications with their correspondi
34、ng European publications This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revi
35、sions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). NOTE When an international publication has been modified by common modifi
36、cations, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-2 1985 Electromechanical components for electronic equipment Basic testing procedures and measuring methods Part 2: General examination, electrical continuity and contact resistance tests, insulation
37、 tests and voltage stress tests BS EN 60512-1-4:1997 IEC 60512-1-4:1997 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international
38、 level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would
39、be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an indivi
40、dual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001.
41、 Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards B
42、SI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centr
43、e. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44
44、 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all
45、 BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means ele
46、ctronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.
