1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationCombined flexible materials for electrical insulation Part 1: Definitions and general requirementsBS EN 60626-1:2012National forewordThis British Standard is the UK implementatio
2、n of EN 60626-1:2012. It is identical to IEC 60626-1:2009. It supersedes BS EN 60626-1:1996, which will be withdrawn on 23 March 2015.The UK participation in its preparation was entrusted to Technical Committee GEL/15, Solid electrical insulating materials.A list of organizations represented on this
3、 committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2012Published by BSI Standards Limited 2012 ISBN 978 0 580 61366 1 ICS
4、01.040.29; 29.035.01 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2012.Amendments issued since publicationDate Text affectedBRITISH STANDARDBS EN 60
5、626-1:2012EUROPEAN STANDARD EN 60626-1 NORME EUROPENNE EUROPISCHE NORM May 2012 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Brussels 2012
6、 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60626-1:2012 E ICS 29.035.01 Supersedes EN 60626-1:1995 + A1:1996English version Combined flexible materials for electrical insulation - Part 1: Definitions and general requirements
7、 (IEC 60626-1:2009) Matriaux combins souples destins lisolement lectrique - Partie 1: Dfinitions et exigences gnrales (CEI 60626-1:2009) Flexible Mehrschichtisolierstoffe zur elektrischen Isolierung - Teil 1: Definitionen und allgemeine Anforderungen (IEC 60626-1:2009) This European Standard was app
8、roved by CENELEC on 2012-03-23. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nat
9、ional standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its
10、own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, I
11、celand, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 60626-1:2012EN 60626-1:2012 - 2 - Foreword The text of document 15/469/CDV, future edition 3 of IEC 6
12、0626-1, prepared by IEC/TC 15 “Solid electrical insulating materials“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60626-1:2012. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical nat
13、ional standard or by endorsement (dop) 2012-12-23 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2015-03-23 This document supersedes EN 60626-1:1995 + A1:1996. EN 60626-1:2012 includes the following significant technical changes with respect to E
14、N 60626-1:1995: The Scope was revised specifying treatment of mica paper, and Table 1 was revised cancelling materials no longer in use and introducing newer materials. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/o
15、r CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 60626-1:2009 was approved by CENELEC as a European Standard without any modification. BS EN 60626-1:2012- 3 - EN 60626-1:2012 Annex ZA (normative) Normativ
16、e references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references,
17、 the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60554-3-1 1979 Specification for cellulosic paper
18、s for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: General purpose electrical paper - - IEC 60626-3 2008 Combined flexible materials for electrical insulation - Part 3: Specifications for individual materialsEN 60626-3 + corr. October 2008 2008 IEC 60641-3-2 2007
19、Pressboard and presspaper for electrical purposes - Part 3: Specifications for individual materials - Sheet 2: Requirements for presspaper, types P.2.1, P.4.1, P.4.2, P.4.3 and P.6.1 EN 60641-3-2 2008 IEC 60674-3-2 1992 Specification for plastic films for electrical purposes - Part 3: Specifications
20、 for individual materials - Sheet 2: Requirements for balanced biaxially oriented polyethylene terephthalate (PET) films used for electrical insulation EN 60674-3-2 1998 IEC 60674-3-4 to 6 1993 Specification for plastic films for electrical purposes - Part 3: Specifications for individual materials
21、- Sheets 4 to 6: Requirements for polyimide films used for electrical insulation EN 60674-3-4 to 6 1995 IEC 60674-3-8 - Plastic films for electrical purposes - Part 3: Specifications for individual materials - Sheet 8: Balanced biaxially oriented polyethylene naphthalate (PEN) films used for electri
22、cal insulation EN 60674-3-8 - IEC 60819-3-1 2001 Non-cellulosic papers for electrical purposes - Part 3: Specifications for individual materials - Sheet 1: Filled glass paper EN 60819-3-1 2001 IEC 60819-3-2 2001 Non-cellulosic papers for electrical purposes - Part 3: Specifications for individual ma
23、terials - Sheet 2: Hybrid inorganic-organic paper EN 60819-3-2 2001 IEC 60819-3-3 + corr. February 2006 2008 Non-cellulosic papers for electrical purposes - Part 3: Specifications for individual materials - Sheet 3: Unfilled aramid (aromatic polyamide) papers EN 60819-3-31) 2006 1) EN 60819-3-3 is s
24、uperseded by EN 60819-3-3:2011, which is based on IEC 60819-3-3:2011. BS EN 60626-1:2012EN 60626-1:2012 - 4 - Publication Year Title EN/HD Year IEC 60819-3-4 2001 Non-cellulosic papers for electrical purposes - Part 3: Specifications for individual materials - Sheet 4: Aramid fibre paper containing
25、not more than 50 % of mica particles EN 60819-3-4 2001 BS EN 60626-1:2012 4 60626-1 IEC:2009 INTRODUCTION This International standard is one of a series which deals with combined flexible materials consisting of two or more different insulating materials laminated together. The components of the com
26、bined materials are plastic films and/or fibrous materials such as papers, woven or non-woven fabrics, impregnated or not impregnated. This series consist of three parts describing: Part 1: Definitions and general requirements (IEC 60626-1) Part 2: Methods of test (IEC 60626-2) Part 3: Specification
27、s for individual materials (IEC 60626-3) BS EN 60626-1:201260626-1 IEC:2009 5 COMBINED FLEXIBLE MATERIALS FOR ELECTRICAL INSULATION Part 1: Definitions and general requirements 1 Scope This part of IEC 60626 contains the definitions related to and the general requirements to be fulfilled by combined
28、 flexible materials for electrical insulation. This standard does not include mica paper, as primary component, covered by IEC 60371, but mica paper may be used as complementary material. Materials which conform to this specification meet established levels of performance. However, the selection of
29、material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. SAFETY WARNING It is the responsibility of the user of the methods contained or referred to in this document to e
30、nsure that they are used in a safe manner. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amen
31、dments) applies. NOTE The list of normative references is extensive because, in order to obtain a combination of two or more materials for electrical insulation, it is necessary that those base materials (paper, film, etc) shall conform to the requirements set forth, in the appropriate specification
32、 of the base material alone, for that purpose. This rule shall be applied also in the development of new possible combinations; to this end, specifications of materials not actually used, but referenced, may be eligible for future developments. IEC 60554-3-1:1979, Specification for cellulosic papers
33、 for electrical purposes Part 3: Specifications for individual materials Sheet 1: General purpose electrical paper IEC 60626-3:2008, Combined flexible materials for electrical insulation Part 3: Specifications for individual materials IEC 60641-3-2:2007, Pressboard and presspaper for electrical purp
34、oses Part 3: Specifications for individual materials Sheet 2: Requirements for presspaper, types P.2.1, P.4.1, P.4.2, P.4.3 and P.6.1 IEC 60674-3-2:1992, Specification for plastic films for electrical purposes Part 3: Specifications for individual materials Sheet 2: Requirements for balanced biaxial
35、ly oriented polyethylene terephthalate (PET) films used for electrical insulation IEC 60674-3-4:1993, Specification for plastic films for electrical purposes Part 3: Specifications for individual materials Sheet 4: Requirements for polyimide (PI) films used for electrical insulation BS EN 60626-1:20
36、12 6 60626-1 IEC:2009 IEC 60674-3-8:, Specification for plastic films for electrical purposes Part 3: Specifications for individual materials Sheet 8: Requirements for balanced biaxially oriented polyethylene naphthalate (PEN) films used for electrical insulation 1IEC 60819-3-1:2001, Non-cellulosic
37、papers for electrical purposes Part 3: Specifications for individual materials Sheet 1: Filled glass paper IEC 60819-3-2:2001, Non-cellulosic papers for electrical purposes Part 3: Specifications for individual materials Sheet 2: Hybrid inorganic-organic paper IEC 60819-3-3:2008, Non-cellulosic pape
38、rs for electrical purposes Part 3: Specifications for individual materials Sheet 3: Unfilled aramid (aromatic polyamide) papers IEC 60819-3-4: 2001, Non-cellulosic papers for electrical purposes Part 3: Specifications for individual materials Sheet 4: Aramid fibre paper containing not more than 50 %
39、 of mica particles 3 Terms and definitions For the purpose of this document, the following terms and definitions apply: 3.1 full width material material of production width, for example about 1 m, as ordered 3.2 slit material (tape) material cut from full width material 3.3 duplex material laminate
40、consisting of two layers of insulating materials 3.4 triplex material laminate consisting of three layers of insulating materials 3.5 quadruplex material laminate consisting of four layers of insulating materials 4 Designation Particular types of combined flexible insulating materials may be designa
41、ted by using the relevant combinations of code letters for the form and nature of the main components, separated by a hyphen. EXAMPLES: F PI,C G. The more commonly used materials are listed in Table 1. 1To be published. BS EN 60626-1:201260626-1 IEC:2009 7 Specific characteristics of a particular co
42、mbined material (duplex or triplex, particular characteristics of the basic material, impregnating material, bonding agent, etc.) are described by additional data following the designation in Table 1. EXAMPLE for designation: P-C/F-PET is a layer of paper consisting of cellulose, laminated with a fi
43、lm consisting of polyethylene terephthalate. In some cases, the identification of specific characteristics such as the following may be useful: Absorbent - porous Calendered type Lengthwise oriented Lengthwise reinforced Creped Embossed Varnished Impregnated NOTE This list is for guidance only and i
44、s not limiting. Code designations are in accordance with ISO standards. Table 1 Commonly used flexible materials Form of component Code designation Nature of the component Code designation IEC normative reference Film F Polyethylene terephthalate Polyethylene naphtalate Polyimide PET PEN PI 60674-3-
45、2 60674-3-8 60674-3-4 Paper and non-woven fabric and mats P Cellulose paper Aramid paper (Aromatic Polyamide) Polyethylene terephthalate non woven Filled glass paper Hybrid inorganic/organic paperC PAa PET FG H 60554-3-1; 60641-3-260819-3-3; 60819-3-4 n. a. 60819-3-1 60819-3-2 Woven fabrics C Cellul
46、ose Glass Polyethylene terephthalate C G PET n. a. Adhesive A Thermoplastic Thermosetting Tp Ts n. a. n.a. = not available 5 General requirements 5.1 The material may be delivered in sheets cut to length or in rolls. 5.2 All materials in any one consignment shall be consistent and have properties wi
47、thin the limits of this standard throughout the whole sheet or throughout the whole length of each roll. The surface shall be uniform, reasonably smooth and reasonably free from defects such as bubbles, pin holes, creases and flaws. BS EN 60626-1:2012 8 60626-1 IEC:2009 5.3 When delivered in rolls,
48、it shall be capable of being unrolled without damage. 5.4 The combined materials shall be free of conducting particles and other undesirable inclusions. 5.5 Materials delivered in sheets cut to length shall be reasonably free from warp. NOTE After bonding, materials produced in roll form often assum
49、e a “roll set“ which depends upon time and temperature of storage. Sheets made from such rolls may require appreciable time before warp is relieved. 6 Dimensions Thickness and thickness tolerances are dealt with in IEC 60626-3. Other dimensions and tolerances shall be agreed by the purchaser and the supplier. 7 Joins For material in roll form, the allowable frequency of joins, the details of their construction, and identification shall be agreed by the purchaser
