1、BRITISH STANDARD BSEN 61049:1993 Specification for Capacitors for use in tubular fluorescent and other discharge lamp circuits Performance requirements The European Standard EN61049:1993 has the status of a British Standard UDC 621.327.534.15.032BS EN 61049:1993 This British Standard, having been pr
2、epared under the directionof the Electrical Illuminations Standards PolicyCommittee, was publishedunderthe authority ofthe Standards Board and comesinto effect on 15 September 1993 BSI 04-1999 The following BSI references relate to the work on this standard: Committee reference LGL/21 Draft for comm
3、ent8928666 DC ISBN 0 580 22483 X Cooperating organizations The European Committee for Electrotechnical Standardization (CENELEC), under whose supervision this European Standard was prepared, comprises thenational committees of the following countries: Austria Italy Belgium Luxembourg Denmark Netherl
4、ands Finland Norway France Portugal Germany Spain Greece Sweden Iceland Switzerland Ireland United Kingdom Amendments issued since publication Amd. No. Date CommentsBS EN 61049:1993 BSI 04-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 Text of EN610
5、49 3 National annex NA (informative) Original IEC text amended by CENELEC common modifications 9 National annex NB (informative) Committees responsible 10 National annex NC (informative) Cross-references 10BS EN 61049:1993 ii BSI 04-1999 National foreword This British Standard has been prepared unde
6、r the direction of the Electrical Illuminations Standards Policy Committee and is the English language version of EN61049:1993 Capacitors for use in tubular fluorescent and other discharge lamp circuits. Performance requirements, published by the European Committee for Electrotechnical Standardizati
7、on (CENELEC). It was derived by CENELEC from IEC1049:1991, together with its Corrigendum:1992, published by the International Electrotechnical Commission (IEC). The CENELEC common modifications have been implemented at the appropriate places in the text and are indicated by a side line in the margin
8、 Parts of the original IEC text which do not form part of the text of EN61049 have been quoted in National annex NA. Textual error. The common modification in clause4, which refers to clause16, should read “clause16 of IEC1048”. This British Standard, together with BSEN61048, supersedes BS4017:1979
9、 which is withdrawn. The following print types are used in this standard: requirement proper: in roman type; test specification: in italic type; notes: in smaller roman type. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are res
10、ponsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages2to10 and a back cover. This standard has been u
11、pdated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61049 May 1993 UDC 621.327.534.15.032 Descriptors: Discharge lamp, tubular lamp, fluorescent lamp, capacit
12、or, characteristic, electrical capacitance, test, specification English version Capacitors for use in tubular fluorescent and other discharge lamp circuits Performance requirements (IEC1049:1991+corrigendum1992,modified) Condensateurs destins tre utiliss dans les circuits de lampes tubulaires fluore
13、scence et autres lampes dcharge Prescriptions de performances (CEI 1049:1991+corrigendum1992, modifie) Kondensatoren fr Entladungslampen, insbesondere Leuchtstofflampen-Anlagen Leistungsanforderungen (IEC1049:1991+corrigendum1992, modifiziert) This European Standard was approved by CENELEC on 1992-1
14、2-09. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obt
15、ained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Cen
16、tral Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdo
17、m. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1993 Copyright reserved to CENELEC members Ref. No. EN61049:1993 EEN 61049:1993
18、 BSI 04-1999 2 Foreword At the request of CENELEC Technical Committee TC34Z, Luminaires and associated equipment, the text of the International Standard IEC1049:1991 and its corrigendum of January1992, together with the common modifications prepared by TC34Z, was submitted to the CENELEC members for
19、 formal vote in July1992 for acceptance as a European Standard. The text of the draft was approved by CENELEC as EN61049 on9 December1992. The following dates were fixed: For products which have complied with the relevant national standard before1993-12-01, as shown by the manufacturer or by a certi
20、fication body, this previous standard may continue to apply for production until 1998-12-01. Annexes designated “normative” are part of the body of the standard. In this standard, Annex A, Annex B and Annex ZA are normative. Contents Page Foreword 2 1 General 3 1.1 Scope 3 1.2 Normative references 3
21、 2 Definitions 3 3 General notes on tests 3 4 Testing sequence 4 5 Marking 4 6 Capacitance 4 7 Change of capacitance with temperature 5 8 Endurance test 5 Annex A (normative) Conformity of production 8 Annex B (normative) Test voltage 8 Annex ZA (normative) Other international publications quoted in
22、 this standard with thereferences of the relevant European publications 8 latest date of publication ofan identical national standard (dop) 1993-12-01 latest date of withdrawal ofconflicting national standards (dow) 1993-12-01EN 61049:1993 BSI 04-1999 3 1 General 1.1 Scope This International Standar
23、d states the requirements for both self-healing and non-self-healing continuously rated a.c. capacitors of up to and including2,5kvar, and not less than0,14F, having a rated voltage not exceeding1000V, which are intended for use in discharge lamp circuits 1)operating at50Hz or60Hz and at altitudes u
24、p to3000m. It covers capacitors intended for connection in shunt or in series with the lamp circuit or an effective combination of these. It covers only impregnated or unimpregnated capacitors, having a dielectric of paper, plastic film or a combination of both, either metallized or with metal foil
25、electrodes. This standard does not cover radio-interference suppressor capacitors the requirements for which are found in IEC384-14. Tests in this standard are type tests. Guidance on conformity of production is given in Annex A. 1.2 Normative references The following standards contain provisions wh
26、ich, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Standard are encouraged to investigate the possibilit
27、y of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. IEC standards: IEC 68-2-14:1984, Environmental testing Part2: Tests. Test N: Change of temperature. Amendment No.1 (1986). IEC 384-14:1981, F
28、ixed capacitors for use in electronic equipment Part14: Sectional specification: Fixed capacitors for radio interference suppression. Selection of methods of test and general requirements. IEC 410:1973, Sampling plans and procedures for inspection by attributes. IEC 1048:1990, Capacitors for use in
29、tubular fluorescent and other discharge lamp circuits. General and safety requirements. 2 Definitions For the purposes of this International Standard, the definitions of IEC1048 shall apply. 3 General notes on tests All capacitors specified in this standard shall comply with the requirements of IEC1
30、048. Tests according to this standard are type tests. NOTEThe requirements and tolerances permitted by this standard are related to testing of a type test sample submitted for that purpose. In principle, this type test sample should consist of units having characteristics typical of the manufacturer
31、s production and be as close to the production centre points as possible. It may be expected with the tolerances given in the standard that products manufactured in accordance with the type test sample will comply with the standard for the majority of the production. Due to the production spread, it
32、 is inevitable, however, that there may be products outside the specified tolerances. For guidance on sampling plans and procedures for inspection by attributes, see IEC410. Capacitors shall be subjected to the tests detailed in clause4. Unless otherwise specified, tests shall be carried out at a te
33、mperature of20C5C, using where appropriate a voltage source as detailed inAnnex B. Test temperatures specified in particular clauses shall be subject to a tolerance of 2 C, unless otherwise stated. 1) These lamps and associated ballasts are covered in the specifications of the following IEC publicat
34、ions: 81:1984, Tubular fluorescent lamps for general lighting service. Amendment No.1 (1987). Amendment No.2 (1988). 188:1974, High-pressure mercury vapour lamps. Amendment No.1 (1976). Amendment No.2 (1979). Amendment No.3 (1984). Amendment No.4 (1988). 192:1973, Low-pressure sodium vapour lamps. A
35、mendment No.2 (1988). 921:1988, Ballasts for tubular fluorescent lamps. Performance requirements. 923:1988, Ballasts for discharge lamps (excluding tubular fluorescent lamps). Performance requirements.EN 61049:1993 4 BSI 04-1999 Unless otherwise specified, the type shall be deemed to comply with any
36、 one clause if not more than one failure occurs in the test of that clause. If three or more failures occur, the type shall be rejected. If two failures occur in any one test, that test, and any preceding tests which may have influenced the test results, shall be repeated on the same quantity of cap
37、acitors and if any further failures occur, the type shall be rejected. For a range of capacitors of the same construction, rated voltage and cross-sectional shape, each group referred to in clause4 shall contain as nearly as possible equal numbers of capacitors of the highest capacitance and the low
38、est capacitance in that range. Moreover, the manufacturer shall provide data on the ratio of capacitance per area outer total surface of the container of each capacitance value in the range. The capacitor with the maximum capacitance per unit surface area shall also be tested if this ratio exceeds t
39、hat of the maximum capacitance value in the range by10% or greater. Similarly, the capacitor with the minimum capacitance per unit area shall also be tested if the ratio is less than that of the minimum capacitance value in the range by10% or greater. “Area” denotes total outer surface area of capac
40、itor case ignoring small protrusions, terminals and fixing studs. With this procedure the tests qualify all intermediate values of capacitance in the range. NOTE 1The “same construction” includes for example the same dielectric material, dielectric thickness and type of case (metal or plastic). NOTE
41、 2“Cross-sectional shape” means: round, rectangular, oval, etc. 4 Testing sequence A total of47 non-self-healing capacitors, or in the case of self-healing types52 capacitors, shall be taken and divided into four groups as indicated below. NOTEFor capacitors above1kvar the quantities for testing can
42、 be agreed between manufacturer and testing authority. The following initial test shall be applied to all the capacitors: capacitance measurement in accordance with clause6. The first group of5 capacitors shall be subjected to the test for deviation of capacitance with temperature in accordance with
43、 clause7. The second group of5 capacitors, completed with the5 capacitors of the first group, shall be subjected to the self-healing test in accordance with clause16. This test is only applicable for self-healing capacitors. The third group of21 capacitors shall be subjected to the endurance test in
44、 accordance with clause8. The fourth group of21 capacitors shall be retained as spares in the event of a repeat test being necessary in the first three groups. 5 Marking The marking requirements of IEC1048 shall apply, together with the following. 5.1 Period of manufacture, which may be in code form
45、 5.2 For unimpregnated metallized plastic film shunt capacitors of250V rated voltage or less, with a t cnot higher than85C, the letter “D”. 6 Capacitance The capacitance of each capacitor when measured at50Hz or60Hz, as appropriate, shall be within the tolerance limits marked on the capacitor. Capa
46、citance shall be measured using a method which excludes errors due to harmonics. The accuracy of measurement shall be better than0,25% of the capacitance measured. The measuring voltage shall not be higher than the rated voltage of the capacitor; the frequency shall be as near as possible to the rat
47、ed frequency. Measurement at other frequencies is allowed, provided that the frequency dependence of the capacitance is very small. The measured capacitance shall not deviate from the rated capacitance by more than the tolerance marked on the capacitor. Compliance is checked by measurement.EN 61049:
48、1993 BSI 04-1999 5 7 Change of capacitance with temperature The change of capacitance with temperature shall stay within acceptable limits. Compliance is checked by the tests of7.1 to7.6. 7.1 Measurements of capacitance shall be made under the conditions prescribed in clause6. 7.2 The capacitor shal
49、l be measured at each of the following temperatures in turn: a) 20C 2C; b) rated minimum temperature 3C (C T min ); c) 20C2C; d) rated maximum temperature2C (C T max ); e) 20C 2C. 7.3 Capacitance measurements shall be made at each of the temperatures specified in7.2 after the capacitor has reached thermal stability. The measuring voltage shall be applied only for the minimum time necessary to make the capacitance measurements. The condition of thermal stability shall be judged to have been reached when two readings of capa
