1、BSI Standards PublicationIndustrial communication networks Fieldbus specificationsPart 3-13: Data-link layer service definition Type 13 elementsBS EN 61158-3-13:2014National forewordThis British Standard is the UK implementation of EN 61158-3-13:2014. It isidentical to IEC 61158-3-13:2014. It supers
2、edes BS EN 61158-3-13:2008which is withdrawn.The UK participation in its preparation was entrusted to Technical Com-mittee AMT/7, Industrial communications: process measurement andcontrol, including fieldbus.A list of organizations represented on this committee can be obtained onrequest to its secre
3、tary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 79366 0ICS 25.040.40; 35.100.20; 35.240.50Compliance with a Bri
4、tish Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2014.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61158-3-13:2014EUROPEAN STANDARD N
5、ORME EUROPENNE EUROPISCHE NORM EN 61158-3-13 October 2014 ICS 25.040.40; 35.100.20; 35.110 Supersedes EN 61158-3-13:2008 English Version Industrial communication networks - Fieldbus specifications - Part 3-13: Data-link layer service definition - Type 13 elements (IEC 61158-3-13:2014) Rseaux de comm
6、unication industriels - Spcifications des bus de terrain - Partie 3-13: Dfinition des services de la couche liaison de donnes - Elments de type 13 (CEI 61158-3-13:2014) Industrielle Kommunikationsnetze - Feldbusse - Teil 3-13: Dienstfestlegungen des Data Link Layer (Sicherungsschicht) - Typ 13-Eleme
7、nte (IEC 61158-3-13:2014) This European Standard was approved by CENELEC on 2014-09-17. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date
8、lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translatio
9、n under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmar
10、k, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Com
11、mittee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CE
12、NELEC Members. Ref. No. EN 61158-3-13:2014 E BS EN 61158-3-13:2014EN 61158-3-13:2014 - 2 - Foreword The text of document 65C/759/FDIS, future edition 2 of IEC 61158-3-13, prepared by SC 65C “Industrial networks“ of IEC/TC 65 “Industrial-process measurement, control and automation“ was submitted to t
13、he IEC-CENELEC parallel vote and approved by CENELEC as EN 61158-3-13:2014. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-06-17 latest date by which the national s
14、tandards conflicting with the document have to be withdrawn (dow) 2017-09-17 This document supersedes EN 61158-3-13:2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identif
15、ying any or all such patent rights. This document has been prepared under a mandate given to CENELEC by the European Commission and the European Free Trade Association. Endorsement notice The text of the International Standard IEC 61158-3-13:2014 was approved by CENELEC as a European Standard withou
16、t any modification. In the official version, for Bibliography, the following notes have to be added for the standards indicated: IEC 61158-1 NOTE Harmonized as EN 61158-1. IEC 61158-6-13 NOTE Harmonized as EN 61158-6-13. IEC 61784-2 NOTE Harmonized as EN 61784-2. BS EN 61158-3-13:2014- 3 - EN 61158-
17、3-13:2014 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition
18、 cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest ve
19、rsions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 61158-4-13 2014 Industrial communication networks - Fieldbus specifications - Part 4-13: Data-link layer protocol specification - Type 13 elements EN 61158-4-13 1)IEC 61158-
20、5-13 2014 Industrial communication networks - Fieldbus specifications - Part 5-13: Application layer service definition - Type 13 elements EN 61158-5-13 2014 ISO/IEC 7498-1 - Information technology - Open Systems Interconnection - Basic Reference Model: The Basic Model - - ISO/IEC 7498-3 - Informati
21、on technology - Open Systems Interconnection - Basic Reference Model: Naming and addressing - - ISO/IEC 8802-3 2000 Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple acc
22、ess with collision detection (CSMA/CD) access method and physical layer specifications - - ISO/IEC 10731 - Information technology - Open Systems Interconnection - Basic Reference Model - Conventions for the definition of OSI services - - IETF RFC 768 - User Datagram Protocol - - IETF RFC 791 - Inter
23、net Protocol - - IETF RFC 793 - Transmission Control Protocol - - 1) To be published. BS EN 61158-3-13:2014 2 IEC 61158-3-13:2014 IEC 2014 CONTENTS INTRODUCTION . 6 1 Scope . 7 1.1 General . 7 1.2 Specifications 7 1.3 Conformance . 7 2 Normative references . 8 3 Terms, definitions, symbols, abbrevia
24、tions and conventions . 8 3.1 Reference model terms and definitions 8 3.2 Service convention terms and definitions . 10 3.3 Data-link service terms and definitions 11 3.4 Symbols and abbreviations 15 3.5 Common conventions 16 3.6 Additional Type 13 conventions . 17 4 Data-link service and concept .
25、18 4.1 Overview . 18 4.2 Detailed description of isochronous-data services . 27 4.3 Detailed description of asynchronous-data service 28 4.4 Detailed description of exception-signaling services 35 4.5 NMT-status services 37 5 Data-link management services (and concepts) 38 5.1 General . 38 5.2 Facil
26、ities of the DLMS . 38 5.3 Services of the DL-management 38 5.4 Overview of interactions 39 5.5 Detail specification of service and interactions 40 Bibliography 45 Figure 1 Relationships of DLSAPs, DLSAP-addresses and group DL-addresses 13 Figure 2 Type 13 communication architecture 18 Figure 3 Sequ
27、ence diagram of isochronous-data service . 19 Figure 4 Sequence diagram of service-data service . 20 Figure 5 Sequence diagram of an unspecified-data transfer service . 21 Figure 6 Sequence diagram of a status-data transfer service . 21 Figure 7 Sequence diagram of an ident-data transfer service . 2
28、2 Figure 8 Sequence diagram of a sync-data transfer service . 23 Figure 9 Sequence diagram of an NMT-command transfer service . 24 Figure 10 Sequence diagram of an exception-signaling service . 25 Figure 11 Sequence diagram of a NMT-status transfer service 26 Figure 12 Reset, Set value and Get value
29、 services 39 Figure 13 Event and Frame status service . 40 Table 1 Type 13 node ID assignment . 27 Table 2 Primitives and parameters used on the isochronous data service 27 BS EN 61158-3-13:2014IEC 61158-3-13:2014 IEC 2014 3 Table 3 Transmit /Receive isochronous-data primitives and the parameters .
30、28 Table 4 Primitives and parameters used on service data transfer service . 28 Table 5 Transmit / Receive service-data primitives and the parameters . 29 Table 6 Primitives and parameters used on the unspecified-data service . 30 Table 7 Transmit / receive unspecified-data primitives and the parame
31、ters 30 Table 8 Primitives and parameters used on status-data transfer service 31 Table 9 Status data primitives and the parameters . 31 Table 10 Primitives and parameters used on ident-data transfer service 32 Table 11 Ident data primitives and the parameters . 33 Table 12 Primitives and parameters
32、 used on sync-data transfer service. 33 Table 13 Sync data primitives and the parameters . 34 Table 14 Primitives and parameters used on the NMT-command service . 34 Table 15 NMT-command primitives and the parameters . 35 Table 16 Primitives and parameters used on the exception-signaling service . 3
33、5 Table 17 Exception-signaling initialization primitives and the parameters . 36 Table 18 Exception signaling initialization primitives and the parameters . 36 Table 19 Primitives and parameters used on the NMT-status service . 37 Table 20 NMT-status primitives and the parameters. 37 Table 21 Summar
34、y of DL-management primitives and parameters . 39 Table 22 DLM-Reset primitives and parameters . 40 Table 23 DLM-Set-value primitives and parameters . 41 Table 24 DLM-Get-value primitives and parameters . 42 Table 25 Event primitives and parameters . 42 Table 26 Event-related state change variables
35、. 43 Table 27 Frame status primitives and parameters 43 Table 28 Frame parameters . 44 BS EN 61158-3-13:2014 6 IEC 61158-3-13:2014 IEC 2014 INTRODUCTION This part of IEC 61158 is one of a series produced to facilitate the interconnection of automation system components. It is related to other standa
36、rds in the set as defined by the “three-layer” fieldbus reference model described in IEC 61158-1. Throughout the set of fieldbus standards, the term “service” refers to the abstract capability provided by one layer of the OSI Basic Reference Model to the layer immediately above. Thus, the data-link
37、layer service defined in this standard is a conceptual architectural service, independent of administrative and implementation divisions. BS EN 61158-3-13:2014IEC 61158-3-13:2014 IEC 2014 7 INDUSTRIAL COMMUNICATION NETWORKS FIELDBUS SPECIFICATIONS Part 3-13: Data-link layer service definition Type 1
38、3 elements 1 Scope General 1.1This part of IEC 61158 provides common elements for basic time-critical messaging communications between devices in an automation environment. The term “time-critical” is used to represent the presence of a time-window, within which one or more specified actions are req
39、uired to be completed with some defined level of certainty. Failure to complete specified actions within the time window risks failure of the applications requesting the actions, with attendant risk to equipment, plant and possibly human life. This standard defines in an abstract way the externally
40、visible service provided by the Type 13 fieldbus data-link layer in terms of a) the primitive actions and events of the service; b) the parameters associated with each primitive action and event, and the form which they take; and c) the interrelationship between these actions and events, and their v
41、alid sequences. The purpose of this standard is to define the services provided to the Type 13 fieldbus application layer at the boundary between the application and data-link layers of the fieldbus reference model, and systems management at the boundary between the data-link layer and systems manag
42、ement of the fieldbus reference model. Specifications 1.2The principal objective of this standard is to specify the characteristics of conceptual data-link layer services suitable for time-critical communications, and thus supplement the OSI Basic Reference Model in guiding the development of data-l
43、ink protocols for time-critical communications. A secondary objective is to provide migration paths from previously-existing industrial communications protocols. This specification may be used as the basis for formal DL-Programming-Interfaces. Nevertheless, it is not a formal programming interface,
44、and any such interface will need to address implementation issues not covered by this specification, including a) the sizes and octet ordering of various multi-octet service parameters, and b) the correlation of paired request and confirm, or indication and response, primitives. Conformance 1.3This
45、standard does not specify individual implementations or products, nor do they constrain the implementations of data-link entities within industrial automation systems. There is no conformance of equipment to this data-link layer service definition standard. Instead, conformance is achieved through i
46、mplementation of the corresponding data-link protocol that fulfills the Type 13 data-link layer services defined in this standard. BS EN 61158-3-13:2014 8 IEC 61158-3-13:2014 IEC 2014 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and
47、 are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE All parts of the IEC 61158 series, as well as IEC 61784-1 and IEC 61784-2 are maintained simult
48、aneously. Cross-references to these documents within the text therefore refer to the editions as dated in this list of normative references. IEC 61158-4-13:2014, Industrial communication networks Fieldbus specifications Part 4-13: Data-link layer protocol specification Type 13 elements IEC 61158-5-1
49、3:2014, Industrial communication networks Fieldbus specifications Part 5-13: Application layer service definition Type 13 elements ISO/IEC 7498-1, Information technology Open Systems Interconnection Basic Reference Model: The Basic Model ISO/IEC 7498-3, Information technology Open Systems Interconnection Basic Reference Model: Naming and addressing ISO/IEC 8802-3:2000, Information technology Telecommunicat
