1、BSI Standards PublicationFibre optic interconnectingdevices and passive components Basic test and measurement proceduresPart 3-49: Examinations and measurements Guide pin retention force for rectangular ferrule multi-fibre connectorsBS EN 61300-3-49:2013National forewordThis British Standard is the
2、UK implementation of EN 61300-3-49:2013. It is identical to IEC 61300-3-49:2013.The UK participation in its preparation was entrusted by Technical Committee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre optic interconnecting devices and passive components.A list of organizations represented
3、on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2013.Published by BSI Standards Limited 2013ISBN 978 0 580 75986
4、 4 ICS 33.180.20Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2013.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS E
5、N 61300-3-49:2013EUROPEAN STANDARD EN 61300-3-49 NORME EUROPENNE EUROPISCHE NORM June 2013 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Management Centre: Avenue Marnix 17, B - 1000 Br
6、ussels 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61300-3-49:2013 E ICS 33.180.20 English version Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 3-49: Examinatio
7、ns and measurements - Guide pin retention force for rectangular ferrule multi-fibre connectors (IEC 61300-3-49:2013) Dispositifs dinterconnexion et composants passifs fibres optiques - Procdures fondamentales dessais et de mesures - Partie 3-49 : Examens et mesures - Force de rtention de la broche d
8、e guidage des connecteurs multifibres frule rectangulaire (CEI 61300-3-49:2013) Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prf- Messverfahren - Teil 3-49: Prfungen und Messungen - Fhrungsstiftausziehkraft von rechteckigen Ferrulen von Mehrfachfasersteckverbindern (IE
9、C 61300-3-49:2013) This European Standard was approved by CENELEC on 2013-04-10. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists a
10、nd bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under
11、 the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Esto
12、nia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 61300-3-49:20
13、13EN 61300-3-49:2013 - 2 - Foreword The text of document 86B/3437/CDV, future edition 1 of IEC 61300-3-49, prepared by SC 86B “Fibre optic interconnecting devices and passive components“ of IEC/TC 86 “Fibre optics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-3-
14、49:2013. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-01-10 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2
15、016-04-10 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61300-3-49:201
16、3 was approved by CENELEC as a European Standard without any modification. BS EN 61300-3-49:2013- 3 - EN 61300-3-49:2013 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normativel
17、y referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common
18、modifications, indicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 61300-1 2011 Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 1: General and guidance EN 61300-1 2011 IEC 61300-3-1 - Fibre optic interconnect
19、ing devices and passive components - Basic test and measurement procedures - Part 3-1: Examinations and measurements - Visual examination EN 61300-3-1 - IEC 61754-7 - Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 7: Type MPO connector family EN
20、61754-7 - IEC 61754-10 - Fibre optic connector interfaces - Part 10: Type Mini-MPO connector family EN 61754-10 - IEC 61754-18 - Fibre optic connector interfaces - Part 18: Type MT-RJ connector family EN 61754-18 - BS EN 61300-3-49:2013 2 61300-3-49 IEC:2013 CONTENTS 1 Scope . 5 2 Normative referenc
21、es . 5 3 General description 5 3.1 General . 5 3.2 Test conditions 5 4 Apparatus . 6 4.1 Fixture . 6 4.2 Guide pin chuck 6 4.3 Weight . 6 4.4 Tensile testing machine . 6 5 Procedure . 6 5.1 Method A: Method using weight (Figure 1) . 6 5.2 Method B: Method using tensile testing machine (Figure 2) . 7
22、 6 Details to be specified 8 Figure 1 Method for examination of guide pin retention force (method using weight) 7 Figure 2 Method for examination of guide pin retention force (method using tensile testing machine) . 8 Table 1 Test conditions 6 BS EN 61300-3-49:201361300-3-49 IEC:2013 5 FIBRE OPTIC I
23、NTERCONNECTING DEVICES AND PASSIVE COMPONENTS BASIC TEST AND MEASUREMENT PROCEDURES Part 3-49: Examinations and measurements Guide pin retention force for rectangular ferrule multi-fibre connectors 1 Scope The purpose of this part of IEC 61300 is to describe the procedure required to measure the gui
24、de pin retention force for rectangular ferrule multi-fibre connectors in order to ensure that the pins remain in place during mating/unmating. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. F
25、or dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 61300-1:2011, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 1: General and guidan
26、ce IEC 61300-3-1, Fibre optic interconnecting devices and passive components Basic test and measurement procedures Part 3-1: Examinations and measurements Visual examination IEC 61754-7, Fibre optic interconnecting devices and passive components Fibre optic connector interfaces Part 7: Type MPO conn
27、ector family IEC 61754-10, Fibre optic connector interfaces Part 10: Type Mini-MPO connector family IEC 61754-18, Fibre optic connector interfaces Part 18: Type MT-RJ connector family 3 General description 3.1 General This measurement method is applied for optical connectors specified in IEC 61754-7
28、, IEC 61754-10 and IEC 61754-18. This standard describes two methods using weight or a tensile testing machine. The optical connector is held using a fixture. The guide pin is placed in a guide pin chuck. The weight or tensile testing machine is connected to the guide pin chuck. A measurement of gui
29、de pin retention force is taken. 3.2 Test conditions For precise measurements such as for design verification, test conditions shall be controlled accurately as required in Table 1 of IEC 61300-1:2011. Table 1 below is an adaptation of that table. BS EN 61300-3-49:2013 6 61300-3-49 IEC:2013 Table 1
30、Test conditions Temperature T Relative humidity RH 22,0 C to 24,0 C (50,0 10,0) % RH 4 Apparatus 4.1 Fixture The measurement shall not be affected by the connector fixture. The position and direction of connector during the test shall not change as the test is repeated. The connector shall be placed
31、 in the fixture so that the front face of connector housing is retained by the fixture as shown in Figure 1 and Figure 2. 4.2 Guide pin chuck The guide pin chuck shall have a pin retention force much larger than required connector guide pin retention force. More than 200 N is ideal when using a tens
32、ile testing machine. The connection of the guide pin chuck to the weight or tensile testing machine shall not affect the measurement nor divert the applied force from the axis of guide pin. 4.3 Weight The weight to be used depends on the test to be carried out. The weight measurement is used for pas
33、s/fail tests including final inspection. 4.4 Tensile testing machine The tensile testing machine shall be able to record (and/or hold) the maximum value during the measurement. Tensile testing machine measurement is used for design verification testing. 5 Procedure 5.1 Method A: Method using weight
34、(Figure 1) a) Prepare the DUT according to the manufacturers instructions and check the appearance in accordance with IEC 61300-3-1. b) Place the DUT in the fixture and check the appearance. c) Place the guide pin in the chuck. d) Fix the weight to the guide pin chuck. Adjust the total weight of chu
35、ck and weight to the specified value. Ensure the DUT is fixed vertical. e) Apply the weight slowly. Be sure that the DUT remains vertical and the force is applied in the axis of the guide pin. f) Wait for the specified duration. Record whether or not the guide pin remains in place for the specified
36、force. Unless otherwise specified, the minimum duration shall be 5 s. BS EN 61300-3-49:201361300-3-49 IEC:2013 7 Key 1 Fixture 2 DUT (optical connector) 3 Guide pin 4 Guide pin chuck 5 Front face of housing 6 Weight Figure 1 Method for examination of guide pin retention force (method using weight) 5
37、.2 Method B: Method using tensile testing machine (Figure 2) a) Prepare the DUT according to the manufacturers instructions and check the appearance in accordance with IEC 61300-3-1. b) Place the DUT in the fixture and check the appearance. c) Place the guide pin in the chuck. d) Connect guide pin c
38、huck to tensile testing machine. Ensure that the DUT is fixed vertical and the pulling device is precisely aligned on the axis of guide pin. e) Apply tension using the tensile testing machine. The weight of the guide pin chuck should be factored in. Be sure that the DUT remains vertical and the forc
39、e is applied in the axis of the guide pin. Measure and record the maximum value when the guide pin is withdrawn. The rate of application shall be less than 50 mm/s when the rate is not specified. 2 4 6 3 1 5 IEC 485/13 BS EN 61300-3-49:2013 8 61300-3-49 IEC:2013 Key 1 Fixture 2 DUT (optical connecto
40、r) 3 Guide pin 4 Guide pin chuck 5 Front face of housing 6 Tensile testing machine Figure 2 Method for examination of guide pin retention force (method using tensile testing machine) 6 Details to be specified The following details, as applicable, shall be stated in the relevant specification: DUT pr
41、eparation; Acceptable value of guide pin retention force; Maximum weight to be tested when using Method A; Minimum duration when using Method A; 2 4 3 1 6 5 IEC 486/13 BS EN 61300-3-49:201361300-3-49 IEC:2013 9 Rate of application when using Method B; Deviations from this test method. _ BS EN 61300-
42、3-49:2013This page deliberately left blankThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization product
43、s are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based s
44、olutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with
45、the knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and
46、international standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are des
47、igned to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so
48、youll always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You
49、 will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. Wit
