1、BSI Standards PublicationFibre optic interconnecting devices and passive components Fibre optic connector interfacesPart 30: Type CLIK connector seriesBS EN 61754-30:2014National forewordThis British Standard is the UK implementation of EN 61754-30:2014. It isidentical to IEC 61754-30:2014.The UK pa
2、rticipation in its preparation was entrusted by TechnicalCommittee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre opticinterconnecting devices and passive components.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purp
3、ort to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 78752 2ICS 33.180.20Compliance with a British Standard cannot confer immunity fromlegal obligation
4、s.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2014.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61754-30:2014EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61754-30 May 2014 ICS 33.180
5、.20 English Version Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 30: Type CLIK connector series (IEC 61754-30:2014) Dispositifs dinterconnexion et composants passifs fibres optiques - Interfaces de connecteurs fibres optiques - Partie 30: Srie
6、de connecteurs de type CLIK (CEI 61754-30:2014) Lichtwellenleiter - Verbindungselemente und passive Bauteile - Steckgesichter von Lichtwellenleiter-Steckverbindern - Teil 30: Steckverbinderfamilie der Bauart CLIK (IEC 61754-30:2014) This European Standard was approved by CENELEC on 2014-03-13. CENEL
7、EC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on ap
8、plication to the CEN-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-
9、CENELEC Management Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary,
10、 Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique E
11、uropisches Komitee fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2014 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61754-30:2014 E BS EN 61754-30:2014EN 61754-30:2014 - 2 - Foreword
12、 The text of document 86B/3705/FDIS, future edition 1 of IEC 61754-30, prepared by SC 86B “Fibre optic interconnecting devices and passive components“ of IEC/TC 86 “Fibre optics“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 61754-30:2014. The following dates are fixed
13、: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2014-12-13 latest date by which the national standards conflicting with the document have to be withdrawn (dow) 2017-03-13 Attention is drawn to the po
14、ssibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61754-30:2014 was approved by CENELEC as a European
15、Standard without any modification. BS EN 61754-30:2014- 3 - EN 61754-30:2014 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normatively referenced in this document and are indisp
16、ensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, indicated by (mod), the relev
17、ant EN/HD applies. Publication Year Title EN/HD Year IEC 60794-2-50 - Optical fibre cables - Part 2-50: Indoor cables - Family specification for simplex and duplex cables for use in terminated cable assemblies EN 60794-2-50 - IEC 61754-1 - Fibre optic interconnecting devices and passive components -
18、 Fibre optic connector interfaces - Part 1: General and guidance EN 61754-1 - IEC 61755-3 series Fibre optic connector optical interfaces - Part 3: Optical interface EN 61755-3 series BS EN 61754-30:2014 2 61754-30 IEC:2014 CONTENTS INTRODUCTION . 5 1 Scope 6 2 Normative references 6 3 Description 6
19、 4 Interfaces 6 5 PC plug optical interface 7 6 APC plug optical interface . 9 7 PC adaptor optical interface 12 8 APC adaptor optical interface 13 9 Pin gauge for adaptor 15 Figure 1 PC plug interface (isometric view) 7 Figure 2 PC plug interface reference planes 8 Figure 3 Detail A of Figure 1 PC
20、endface geometry 8 Figure 4 Top view (PC) 8 Figure 5 APC plug interface (isometric view) 9 Figure 6 APC plug interface reference planes 10 Figure 7 Detail A of Figure 5 APC endface geometry . 10 Figure 8 Top view (APC) 10 Figure 9 PC adaptor interface (isometric view) . 12 Figure 10 PC adaptor inter
21、face 12 Figure 11 APC adaptor interface (isometric view) . 13 Figure 12 APC adaptor interface 14 Figure 13 Pin gauge for adaptor . 15 Table 1 Intermateability between plugs and adaptors within the IEC 61754-30 series 7 Table 2 Intermateability between plugs within the IEC 61754-30 series 7 Table 3 P
22、C plug dimensions 9 Table 4 APC plug dimensions 11 Table 5 Plug connector interface Ferrule grade . 11 Table 6 Dimensions of the PC adaptor interface 13 Table 7 Dimensions of the APC adaptor interface 14 Table 8 Pin gauge dimensions . 15 BS EN 61754-30:201461754-30 IEC:2014 5 INTRODUCTION The Intern
23、ational Electrotechnical Commission (IEC) draws attention to the fact that it is claimed that compliance with this document may involve the use of a patent concerning a plug interface and an adaptor interface given in Clause 4. IEC takes no position concerning the evidence, validity and scope of thi
24、s patent right. The holder of this patent right has assured the IEC that he/she is willing to negotiate licences under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with IEC
25、. Information may be obtained from: Huber+Suhner AG Degersheimerstrasse 14 9100 Herisau Switzerland Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights other than those identified above. IEC shall not be held responsible for identifyin
26、g any or all such patent rights. ISO (www.iso.org/patents) and IEC (http:/www.iec.ch/tctools/patent_decl.htm) maintain on-line data bases of patents relevant to their standards. Users are encouraged to consult the data bases for the most up to date information concerning patents. BS EN 61754-30:2014
27、 6 61754-30 IEC:2014 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS FIBRE OPTIC CONNECTOR INTERFACES Part 30: Type CLIK connector series 1 Scope This part of IEC 61754 defines the standard interface dimensions for the type CLIK series of connectors. 2 Normative references The following d
28、ocuments, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60794-2-50, Optica
29、l fibre cables Part 2-50: Indoor cables Family specification for simplex and duplex cables for use in terminated cable assemblies IEC 61754-1, Fibre optic connector interfaces Part 1: General and guidance IEC 61755-3 (all parts), Fibre optic connector optical interfaces Part 3: Optical interfaces 3
30、Description The parent connector for the type CLIK connector family is a single position plug connector set of plug/adaptor/plug configuration which is characterized by a 1,25 mm nominal diameter ferrule. The connector includes a ferrule spring loaded in the direction of the optical axis. The optica
31、l alignment mechanism of the connection is of a resilient sleeve style. 4 Interfaces General requirements defined in IEC 61754-1 are valid for this standard. The subsequent pages define the standard interfaces for the type CLIK connector series. The standard interfaces contained in this standard are
32、 listed in the following: INTERFACE IEC 61754-30-1: Simplex plug connector interface PC INTERFACE IEC 61754-30-2: Simplex adaptor interface PC INTERFACE IEC 61754-30-3: Simplex plug connector interface APC 8 INTERFACE IEC 61754-30-4: Simplex adaptor interface APC The following plugs and adaptors sho
33、wn in Table 1 and Table 2 are intermateable. BS EN 61754-30:201461754-30 IEC:2014 7 Table 1 Intermateability between plugs and adaptors within the IEC 61754-30 series Plugs (polishing condition) Adaptors interfaces IEC 61754-30-2 IEC 61754-30-4 Interface IEC 61754-30-1 Mate Not mate Interface IEC 61
34、754-30-3 Not mate Mate Table 2 Intermateability between plugs within the IEC 61754-30 series Plugs (polishing condition) Plugs (polishing condition) IEC 61754-30-1 IEC 61754-30-3 IEC 61754-30-1 Mate Not mate IEC 61754-30-3 Not mate Mate 5 PC plug optical interface PC plug optical interfaces are show
35、n in Figure 1 to 4 and in Table 3. Figure 1 PC plug interface (isometric view) IEC 0271/14 BS EN 61754-30:2014 8 61754-30 IEC:2014 Optical datum target Mechanical reference plane IEC 0272/14 Optical reference plane Figure 2 PC plug interface reference planes The plug of IEC 61754-30-1 has a ferrule
36、with a spherically polished endface, and realizes physical contact (PC). BH No sharp edge D BG BF IEC 0273/14 NOTE Expanded view drawings not-to-scale. Figure 3 Detail A of Figure 1 PC endface geometry Refer to the IEC 61755-3 series for information on the endface geometry requirements of the PC int
37、erface. Figure 4 Top view (PC) IEC 0274/14 BS EN 61754-30:201461754-30 IEC:2014 9 Table 3 PC plug dimensions Reference Dimensions mm Remarks Minimum Basic Maximum AAa6,45 6,55 BFb,c5 30 RadiusBGb0,6 BHb 1,0 B01 4,675 4,725 B05 1,425 1,475 B06 1,3 1,5 B11 1,375 1,425 B13 0,745 0,775 B16 3,925 3,955 C
38、01 8,3 8,5 C02 0,15 0,25 Radius D See Table 5 a Dimension AA is given for plug endface when not mated. It is given for a finished plug endface after all polishing. The ferrule is movable by a certain axial compressing force, with direct contacting endface, and therefore dimension AA is variable. The
39、 ferrule compression force shall be 5,0 N to 6,0 N when the optical datum target, dimension AA is moved to the range 6,0 mm to 6,35 mm. Forces are for buffered fibre only; different cord constructions can result in higher forces, see IEC 60794-2-50. b These dimensional requirements apply to the fini
40、shed ferrule, after all polishing procedures have been completed. c Dimension BF is the radius of the polished ferrule end face. 6 APC plug optical interface APC plug optical interfaces are shown in Figure 5 to 8 and Table 4. Figure 5 APC plug interface (isometric view) IEC 0275/14 BS EN 61754-30:20
41、14 10 61754-30 IEC:2014 Optical datum target Optical reference plane Mechanical reference plane Ferrule Guide key Plane A Plane B IEC 0276/14 Figure 6 APC plug interface reference planes The plug of IEC 61754-30-3 has a ferrule with a spherically angled polished endface and realizes angled physical
42、contact (APC). BH No sharp edge BG BI D IEC 0277/14 NOTE Expanded view, drawings not-to-scale. Figure 7 Detail A of Figure 5 APC endface geometry Refer to the IEC 61755-3 series for information on the endface geometry requirements of the APC interface. Figure 8 Top view (APC) IEC 0278/14 BS EN 61754
43、-30:201461754-30 IEC:2014 11 Table 4 APC plug dimensions Reference Dimensions mm Remarks Minimum Basic Maximum AAa6,45 6,55 See aAMb90 Basic dimension, degrees AN 8 Basic dimension, degrees B01 4,675 4,725 Diameter BIc,d5 12 Radius BGc0,6 BHc 1,0 B05 1,425 1,475 B06 1,3 1,5 B11 1,375 1,425 B13 0,725
44、 0,755 B14 0,935 0,965 B16 3,925 3,955 C01 8,3 8,5 C02 0,15 0,25 Radius D See Table 5 aDimension AA is given for plug endface when not mated. It is given for a finished plug endface after all polishing. The ferrule is movable by a certain axial compressing force, with direct contacting endface, and
45、therefore dimension AA is variable. Ferrule compression force shall be 5,0 N to 6,0 N when the optical datum target, dimension AA is moved to the range 6,0 mm to 6,35 mm. Forces are for buffered fibre only, different cord constructions can result in higher forces, see IEC 60794-2-50. bDimension AM i
46、s defined as an angle between two planes: One plane, plane A, passes through the axis of the ferrule and the axis of symmetry of the key of the angled endface connector plug. The other plane, plane B, passes through the axis of the ferrule and the plane normal to the angled PC reference plane. cThes
47、e dimensional requirements apply to the finished ferrule after all polishing procedures have been completed. d Dimension BI is the radius of the polished ferrule end face. Table 5 shows ferrule grades. Table 5 Plug connector interface Ferrule grade Grade Diameter mm Remarks aMinimum Maximum 1 1,2485
48、 1,2495 2 1,2483 1,2495 3 1,2467 1,2495 aThe ferrule material is zirconia ceramic. Alternative materials may be used for the ferrule, that have directly compatible material properties with zirconia but the endface performance requirements shall be met under all conditions. BS EN 61754-30:2014 12 617
49、54-30 IEC:2014 7 PC adaptor optical interface PC adaptor optical interfaces are shown in Figure 9 and 10 and in Table 6 Figure 9 PC adaptor interface (isometric view) Optical reference plane Mechanical reference plane IEC 0280/14 Figure 10 PC adaptor interface IEC 0279/14 BS EN 61754-30:201461754-30 IEC:2014 13 Table 6 Dimensions of the PC adaptor interface Reference Dimensions mm Rem
