1、BSI Standards PublicationBS EN ISO 1179-1:2013Connections for general useand fluid power Ports andstud ends with ISO 228-1threads with elastomeric ormetal-to-metal sealingPart 1: Threaded portsBS EN ISO 1179-1:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN
2、 ISO1179-1:2013. It supersedes BS EN ISO 1179-1:2008 which iswithdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/18/-/4, Connectors and associated components.A list of organizations represented on this committee can beobtained on request to its secretary.This pu
3、blication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 78395 1ICS 23.100.40Compliance with a British Standard cannot confer immunit
4、y fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 November 2013.Amendments issued since publicationDate Text affectedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1179-1 November 2013 ICS 23.100.40 Supersede
5、s EN ISO 1179-1:2008English Version Connections for general use and fluid power - Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing - Part 1: Threaded ports (ISO 1179-1:2013) Raccordements pour applications gnrales et transmissions hydrauliques et pneumatiques - O
6、rifices et lments mles filetage ISO 228-1 joint en lastomre ou tanchit mtal sur mtal - Partie 1: Orifices filets (ISO 1179-1:2013) Leitungsanschlsse fr allgemeine Anwendung und Fluidtechnik - Einschraublcher und Einschraubzapfen mit Gewinde nach ISO 228-1 und Elastomerdichtung oder metallener Dichtk
7、ante - Teil 1: Einschraublcher (ISO 1179-1:2013) This European Standard was approved by CEN on 12 October 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alt
8、eration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language ma
9、de by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Esto
10、nia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STAN
11、DARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1179-1:2013 EBS EN ISO 1179-1:2013E
12、N ISO 1179-1:2013 (E) 3 Foreword This document (EN ISO 1179-1:2013) has been prepared by Technical Committee ISO/TC 131 “Fluid power systems“ in collaboration with Technical Committee ECISS/TC 110 “Steel tubes, and iron and steel fittings” the secretariat of which is held by UNI. This European Stand
13、ard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2014, and conflicting national standards shall be withdrawn at the latest by May 2014. Attention is drawn to the possibility that some of the elements of this docu
14、ment may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1179-1:2008. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries ar
15、e bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Po
16、rtugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 1179-1:2013 has been approved by CEN as EN ISO 1179-1:2013 without any modification. BS EN ISO 1179-1:2013ISO 1179-1:2013(E) ISO 2013 All rights reserved iiiContents Pag
17、eForeword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 24 Dimensions . 25 Test methods . 36 Designation of ports 37 Identification statement (reference to this part of ISO 1179) . 3Annex A (informative) Port depths from ISO 1179:1981 used in pneumatic applications whe
18、re stud ends interface with ISO 7-1 male taper threads . 5Bibliography 6BS EN ISO 1179-1:2013ISO 1179-1:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is
19、 normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part
20、 in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particula
21、r the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directivesAttention is drawn to the possibility that some of the elements of this documen
22、t may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received. www.iso.org/paten
23、tsAny trade name used in this document is information given for the convenience of users and does not constitute an endorsement.The committee responsible for this document is ISO/TC 131, Fluid power systems, Subcommittee SC 4, Connectors and similar products and components.This second edition cancel
24、s and replaces the first edition (ISO 1179-1:2007), which has been technically revised.ISO 1179 consists of the following parts, under the general title Connections for general use and fluid power Ports and stud ends with ISO 2281 threads with elastomeric or metaltometal sealing: Part 1: Threaded po
25、rts Part 2: Heavyduty (S series) and lightduty (L series) stud ends with elastomeric sealing (type E) Part 3: Lightduty (L series) stud ends with sealing by Oring with retaining ring (types G and H) Part 4: Stud ends for general use only with metaltometal sealing (type B)iv ISO 2013 All rights reser
26、vedBS EN ISO 1179-1:2013ISO 1179-1:2013(E)IntroductionIn fluid power systems, power is transmitted and controlled through a fluid (liquid or gas) under pressure within a circuit. In general applications, a fluid can be conveyed under pressure. Components are connected through their threaded ports by
27、 fluid conductor connectors to tubes and pipes or to hose fittings and hoses.Ports are an integral part of fluid power components, such as pumps, motors, valves, cylinders, etc.For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, ISO/TC 131/SC 4 recommends
28、 that the ISO 6149 series be used because these International Standards specify ports and stud ends with metric threads and O-ring sealing and because the subcommittee would like to help users by recommending one preferred system. ISO/TC 131/SC 4 further recommends that threaded ports and stud ends
29、in accordance with the ISO 1179 series, ISO 9974 series and ISO 11926 series not be used for new designs in hydraulic fluid power applications; these International Standards will be maintained because they specify ports and stud ends that are currently used in hydraulic systems worldwide.For threade
30、d ports and stud ends specified in new designs in pneumatic fluid power applications, ISO/TC 131/SC 4 recommends that ISO 16030 be used, except where products are to interface with ISO 7-1 threads, because the subcommittee would like to help users by recommending one preferred system. ISO/TC 131/SC
31、4 further recommends that threaded ports and stud ends in accordance with the ISO 1179 series not be used for new designs in pneumatic fluid power applications; these International Standards will be maintained because they specify ports and stud ends that are currently used in pneumatic systems worl
32、dwide.Significant testing over more than 35 years of use has confirmed the performance requirements of connection ends made from carbon steel. The stud end connections specified in ISO 1179-2, ISO 1179-3 and ISO 1179-4 apply to connectors detailed in ISO 8434-1, ISO 8434-2 and ISO 8434-41).1) Withdr
33、awn. ISO 2013 All rights reserved vBS EN ISO 1179-1:2013BS EN ISO 1179-1:2013Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 1: Threaded portsCAUTION The use of ports conforming to this part of ISO 1179 with stud
34、ends conforming to the relevant parts of ISO 6149, ISO 9974 and ISO 11926 could lead to a hazardous situation.1 ScopeThis part of ISO 1179 specifies dimensions for ports with ISO 228-1 threads for use with non-adjustable stud ends described in ISO 1179-2, ISO 1179-3 and ISO 1179-4 and with adjustabl
35、e stud ends described in ISO 1179-3.Ports in accordance with this part of ISO 1179 are applicable for use with ISO 1179-2 heavy-duty (S series) stud ends with type E sealing at working pressures up to 63 MPa (630 bar) and light-duty (L series) stud ends at working pressures up to 25 MPa (250 bar), I
36、SO 1179-3 light-duty (L series) stud ends with type G sealing at working pressures up to 31,5 MPa (315 bar) and ISO 1179-3 light-duty (L series) adjustable stud ends with type H sealing at working pressures up to 20 MPa (200 bar), and ISO 1179-4 stud ends with type B sealing at working pressures up
37、to 40 MPa (400 bar) for the S series, up to 25 MPa (250 bar) for the L series, and up to 10 MPa (100 bar) for the LL series,except for the G2 size port, which in hydraulic fluid power systems is used mainly with accumulators and for which ISO 1179-3 and ISO 1179-4 do not specify stud ends. The permi
38、ssible working pressure depends upon size, materials, design, working conditions, application, etc.Users of this part of ISO 1179 should ensure that there is sufficient material around the port to maintain the pressure.NOTE The introduction of this part of ISO 1179 gives recommendations for ports an
39、d stud ends to be used for new designs in hydraulic and pneumatic fluid power applications.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies.
40、For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designationISO 1179-2, Connections for general use and fluid power Ports and stu
41、d ends with ISO 228-1 threads with elastomeric or metaltometal sealing Part 2: Heavyduty (S series) and lightduty (L series) stud ends with elastomeric sealing (type E)ISO 1179-3, Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metaltometal
42、sealing Part 3: Lightduty (L series) stud ends with sealing by Oring with retaining ring (types G and H)INTERNATIONAL STANDARD ISO 1179-1:2013(E) ISO 2013 All rights reserved 1BS EN ISO 1179-1:2013ISO 1179-1:2013(E)ISO 1179-4, Connections for general use and fluid power Ports and stud ends with ISO
43、2281 threads with elastomeric or metaltometal sealing Part 4: Stud ends for general use only with metaltometal sealing (type B)ISO 5598, Fluid power systems and components Vocabulary3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 5598 apply.4 Dimensio
44、nsPorts shall conform to the dimensions shown in Figure 1 and given in Table 1.Dimensions in millimetres/Surface roughness values in micrometresKey1 thread pitch diameteraThread.bDimension L3applies when the tap drill cannot pass through entire boss.Figure 1 ISO 1179-1 port2 ISO 2013 All rights rese
45、rvedBS EN ISO 1179-1:2013ISO 1179-1:2013(E)Table 1 Dimensions for ISO 1179-1 portsDimensions in millimetresThreadd1ad2d3d4bmin. L1L2L3cWref. nom. tol. Type N (narrow) Type W (wide) max. min. min.G 1/8 4,5 9,8+020,15 17,2 1 8,5 10,5 0,1G 1/4 7,5 13,2 20 20,7 1,5 12,5 15,5 0,1G 3/8 9 16,7 23 24,5 2 12
46、,5 15,5 0,1G 1/2 14 21 28 29,6 2,5 15 19 0,1G 3/4 18 26,5 33 36,9 2,5 16,5 20,5 0,2G 1 23 33,3+030,41 46,1 2,5 19 24 0,2G 1 1/4 30 42 51 54 2,5 21,5 26,5 0,2G 1 1/2 36 47,9 56 60,5 2,5 22,5 27,5 0,2G 2 d47 59,7 76 3 26 31 0,2aSize and dimensions in accordance with ISO 228-1.bType N corresponds to th
47、e spot face to be used with male stud end types B and E in ISO 1179-2 and ISO 1179-4. Type W corresponds to the spot face to be used with male stud end types G and H in accordance with ISO 1179-3.cGiven tap drill depths require the use of a bottoming tap to produce the specified full thread lengths.
48、 Where standard taps are used, increase tap drill depths accordingly.dThe G2 size port is used in hydraulic fluid power systems mainly in accumulators. ISO 1179-3 and ISO 1179-4 do not specify stud ends for the G2 size port.5 Test methodsPorts shall be tested along with stud ends in accordance with
49、the test methods and requirements given in ISO 1179-2, ISO 1179-3 and ISO 1179-4. For rated pressures lower than those specified in ISO 1179-2, ISO 1179-3 and ISO 1179-4, the test pressures shall be agreed upon between the manufacturer and user.6 Designation of portsThe ports shall be designated by:a) “Port”;b) reference to this part of ISO 1179, i.e. ISO 1179-1, followed by a spaced hyphen;c) thread size, followed by a spaced hyphen;d) the letter symbol for the relevant spot face type.
