1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN ISO 1183-1:2012Plastics Methods for determining the density of non-cellular plasticsPart 1: Immersion method, liquid pyknometerCopyright European Committee for Standardizat
2、ion Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1183-1:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 1183-1:2012.It supersedes BS EN ISO 1183-1:2004 which is withdr
3、awn.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/21, Testing of plastics.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users a
4、re responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013 ISBN 978 0 580 69765 4 ICS 83.080.01 Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of th
5、eStandards Policy and Strategy Committee on 31 January 2013. Amendments issued since publicationDate T e x t a f f e c t e dCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-EUROPE
6、AN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 1183-1 December 2012 ICS 83.080.01 Supersedes EN ISO 1183-1:2004English Version Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) Plast
7、iques - Mthodes de dtermination de la masse volumique des plastiques non alvolaires - Partie 1: Mthode par immersion, mthode du pycnomtre en milieu liquide et mthode par titrage (ISO 1183-1:2012) Kunststoffe - Verfahren zur Bestimmung der Dichte von nicht verschumten Kunststoffen - Teil 1: Eintauchv
8、erfahren, Verfahren mit Flssigkeitspyknometer und Titrationsverfahren (ISO 1183-1:2012) This European Standard was approved by CEN on 2 June 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of
9、a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German).
10、 A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cy
11、prus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United K
12、ingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1183-1:2012:
13、 ECopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1183-1:2012EN ISO 1183-1:2012 (E) 3 Foreword This document (EN ISO 1183-1:2012) has been prepared by Technical Committ
14、ee ISO/TC 61 “Plastics“ in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2013, and conf
15、licting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This documen
16、t supersedes EN ISO 1183-1:2004. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav R
17、epublic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 1183-1:2012 has bee
18、n approved by CEN as a EN ISO 1183-1:2012 without any modification. Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1183-1:2012ISO 1183-1:2012(E) ISO 2012 All rights re
19、served iiiContents PageForeword iv1 Scope 12 Normative references . 13 Terms and definitions . 14 Conditioning . 25 Methods . 25.1 Method A Immersion method 25.2 Method B Liquid pyknometer method 45.3 Method C Titration method 56 Correction for buoyancy in air . 67 Test report . 7Annex A (informativ
20、e) Liquid systems suitable for use in Method C . 8Annex B (informative) Correction for buoyancy in air 9Bibliography .10Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO
21、1183-1:2012ISO 1183-1:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body intereste
22、d in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Com
23、mission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technica
24、l committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall
25、 not be held responsible for identifying any or all such patent rights.ISO 1183-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 5, Physical-chemical properties.This second edition cancels and replaces the first edition (ISO 1183-1:2004), which has been technically revised.
26、The main changes compared to the previous edition are as follows:a) the equation used to calculate the dependence of the density of air on pressure and temperature in Clause 6 has been replaced by two equations, one for non-tropical conditions, the other for tropical conditions;b) a new annex (Annex
27、 B) has been added showing how the basic air buoyancy correction equation Equation (5) is derived.ISO 1183 consists of the following parts, under the general title Plastics Methods for determining the density of non-cellular plastics: Part 1: Immersion method, liquid pyknometer method and titration
28、method Part 2: Density gradient column method Part 3: Gas pyknometer methodiv ISO 2012 All rights reservedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1183-1:2012INT
29、ERNATIONAL STANDARD ISO 1183-1:2012(E)Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration methodWARNING The use of this part of ISO 1183 might involve hazardous materials, operations or equipment. This part of ISO 118
30、3 does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this part of ISO 1183 to establish appropriate health and safety practices and to determine the applicability of any regulatory limitations prior to use.1 ScopeThis part
31、 of ISO 1183 specifies three methods for the determination of the density of non-cellular plastics in the form of void-free moulded or extruded objects, as well as powders, flakes and granules. Method A: Immersion method, for solid plastics (except for powders) in void-free form. Method B: Liquid py
32、knometer method, for particles, powders, flakes, granules or small pieces of finished parts. Method C: Titration method, for plastics in any void-free form.NOTE This part of ISO 1183 is applicable to pellets as long as they are void-free. Density is frequently used to follow variations in physical s
33、tructure or composition of plastic materials. Density might also be useful in assessing the uniformity of samples or specimens. Often, the density of plastic materials will depend upon the choice of specimen preparation method. When this is the case, precise details of the specimen preparation metho
34、d will have to be included in the appropriate material specification. This note is applicable to all three methods.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated refere
35、nces, the latest edition of the referenced document (including any amendments) applies.ISO 291, Plastics Standard atmospheres for conditioning and testingISO 472, Plastics Vocabulary3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 472 and the following
36、 apply.3.1massmquantity of matter contained in a bodyNOTE It is expressed in kilograms (kg) or grams (g). ISO 2012 All rights reserved 1Copyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IH
37、S-,-,-BS EN ISO 1183-1:2012ISO 1183-1:2012(E)3.2apparent massmAPPmass of a body obtained by measuring its weight using an appropriately calibrated balanceNOTE It is expressed in kilograms (kg) or grams (g).3.3densityratio of the mass m of a sample to its volume V (at the temperature t), expressed in
38、 kg/m3, kg/dm3(g/cm3) or kg/l (g/ml)NOTE The following terms, based upon ISO 80000-4, are given in Table 1 for clarification.Table 1 Density termsTerm Symbol Formulation UnitsDensity m/Vkg/m3kg/dm3(g/cm3)kg/l (g/ml)Specific volume V/m (= 1/)m3/kgdm3/kg (cm3/g)l/kg (ml/g)4 ConditioningThe test atmosp
39、here shall be in accordance with ISO 291. In general, conditioning specimens to constant temperature is not required, because the determination itself brings the specimen to the constant temperature of the test.Specimens which change in density during the test to such an extent that the change is gr
40、eater than the required accuracy shall be conditioned prior to measurement in accordance with the applicable material specification. When changes in density with time or atmospheric conditions are the primary purpose of the measurements, the specimens shall be conditioned as described in the materia
41、l specification and, if no material specification exists, then as agreed upon by the interested parties.5 Methods5.1 Method A Immersion method5.1.1 Apparatus5.1.1.1 Analytical balance or instrument specifically designed for measurement of density, accurate to 0,1 mg.An automatically operating instru
42、ment may be used. The calculation of density may be done automatically using a computer.5.1.1.2 Immersion vessel: a beaker or other wide-mouthed container of suitable size for holding the immersion liquid.5.1.1.3 Stationary support, e.g. a pan straddle, to hold the immersion vessel above the balance
43、 pan.2 ISO 2012 All rights reservedCopyright European Committee for Standardization Provided by IHS under license with CENNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-BS EN ISO 1183-1:2012ISO 1183-1:2012(E)5.1.1.4 Thermometer, graduated at 0,1 C intervals, cover
44、ing the range 0 C to 30 C.5.1.1.5 Wire (if required), corrosion-resistant, of diameter not greater than 0,5 mm, for suspending specimens in the immersion liquid.5.1.1.6 Sinker, of suitable mass to ensure complete immersion of the specimen, for use when the density of the specimen is less than that o
45、f the immersion liquid.5.1.1.7 Pyknometer, with a side-arm overflow capillary, for determining the density of the immersion liquid when this liquid is not water. The pyknometer shall be equipped with a thermometer graduated at 0,1 C intervals from 0 C to 30 C.5.1.1.8 Liquid bath, capable of being th
46、ermostatically controlled to within 0,5 C, for use in determining the density of the immersion liquid.5.1.2 Immersion liquidUse freshly distilled or deionized water, or another suitable liquid, containing not more than 0,1 % of a wetting agent to help in removing air bubbles. The liquid or solution
47、with which the specimen comes into contact during the measurement shall have no effect on the specimen.The density of immersion liquids other than distilled water need not be measured provided they are obtained from an accredited source and are accompanied by a certificate.5.1.3 SpecimensSpecimens m
48、ay be in any void-free form except for powder. They shall be of a convenient size to give adequate clearance between the specimen and the immersion vessel and should preferably have a mass of at least 1 g.When cutting specimens from larger samples, proper equipment shall be used to ensure that the characteristics of the material do not change. The surface of the specimen shall be smooth and free from cavities to minimize the entrapment of air bubbles upon immersion in the liquid, otherwise errors will be introduced.5.1.4 Procedure5.1.4.1 Weigh the specimen, to the nearest 0,1 mg,
