1、BS EN ISO1452-4:2009ICS 23.040.20; 23.040.45; 91.140.60; 93.025NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPlastics pipingsystems for watersupply and for buriedand above-grounddrainage and sewerageunder pressure Unplasticizedpoly(vinyl chloride)(PVC-U)Part 4
2、: Valves (ISO 1452-4:2009)Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/03/2010 02:49, Uncontrolled Copy, (c) BSIThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January2010 BSI 2010ISBN 978 0 580 59543 1Amendments/corrigenda is
3、sued since publicationDate CommentsBS EN ISO 1452-4:2009National forewordThis British Standard is the UK implementation of EN ISO 1452-4:2009. Together with BS EN ISO 1452-1:2009, BS EN ISO 1452-2:2009, BS EN ISO 1452-3:2009 91.140.60; 23.040.20; 23.040.45 Supersedes EN 1452-4:1999, EN 1456-1:2001En
4、glish Version Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 4: Valves (ISO 1452-4:2009) Systmes de canalisations en plastique pour lalimentation en eau, pour branchements et collecteur
5、s dassainissement enterrs et ariens avec pression - Poly(chlorure de vinyle) non plastifi (PVC-U) - Partie 4: Robinets (ISO 1452-4:2009) Kunststoff-Rohrleitungssysteme fr die Wasserversorgung und fr erdverlegte und nicht erdverlegte Abwasserdruckleitungen - Weichmacherfreies Polyvinylchlorid (PVC-U)
6、 - Teil 4: Armaturen (ISO 1452-4:2009) This European Standard was approved by CEN on 4 November 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. U
7、p-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
8、under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Gree
9、ce, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Manageme
10、nt Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 1452-4:2009: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/03/2010 02:49, Uncontrolled Copy, (c) BSIBS EN ISO 1452-4
11、:2009EN ISO 1452-4:2009 (E) 3 Foreword This document (EN ISO 1452-4:2009) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems“, the secretariat of which is held by NEN, in collaboration with Technical Committee ISO/TC 138 “Plastics pipes, fittings and val
12、ves for the transport of fluids“. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at the latest by June 2010. Attention is drawn to
13、 the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1452-4:1999, EN 1456-1:2001. According to the CEN/CENELEC Internal Regulations,
14、 the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
15、 Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/03/2010 02:49, Uncontrolled Copy, (c) BSIBS EN ISO 1452-4:2009ISO 1452-4:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword
16、 iv Introduction.v 1 Scope1 2 Normative references2 3 Terms, definitions, symbols and abbreviated terms .3 4 Material .3 4.1 Valve bodies.3 4.2 Density3 4.3 MRS-value 3 4.4 Additional components.3 5 General characteristics.3 5.1 Appearance 3 5.2 Colour .3 5.3 Opacity3 6 Geometrical characteristics .
17、4 6.1 Measurement of dimensions4 6.2 Nominal diameters 4 6.3 Valves dimensions 4 7 Classification and operating conditions.4 7.1 Classification .4 7.2 Determination of the allowable operating pressure for water up to 45 C 4 8 Mechanical characteristics.5 8.1 Resistance of valve bodies to internal pr
18、essure5 8.2 Crushing test .5 8.3 Durability 5 8.4 Functional properties5 9 Physical characteristics5 10 Chemical characteristics 6 11 Sealing rings 6 12 Adhesives.6 13 Performance requirements.7 14 Marking.7 14.1 General .7 14.2 Minimum required marking 7 14.3 Additional marking 8 Annex A (normative
19、) Imperial(inch)-sized valves9 Bibliography11 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/03/2010 02:49, Uncontrolled Copy, (c) BSIBS EN ISO 1452-4:2009ISO 1452-4:2009(E) iv ISO 2009 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide fed
20、eration of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that comm
21、ittee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accorda
22、nce with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires
23、 approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 1452-4 was prepared by the Europe
24、an Committee for Standardization (CEN) Technical Committee CEN/TC 155, Plastics piping systems and ducting systems, in collaboration with ISO Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supp
25、lies, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). This first edition cancels and replaces ISO 4422-4:1997, which has been technically revised. ISO 1452 consists of the following parts, under the general title Plastics piping systems for water sup
26、ply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U): Part 1: General Part 2: Pipes Part 3: Fittings Part 4: Valves Part 5: Fitness for purpose of the system Guidance for the assessment of conformity is to form the subject of a part 7. L
27、icensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/03/2010 02:49, Uncontrolled Copy, (c) BSIBS EN ISO 1452-4:2009ISO 1452-4:2009(E) ISO 2009 All rights reserved vIntroduction The System Standard, of which this is Part 4, specifies the requirements for a piping system and its components made fr
28、om unplasticized poly(vinyl chloride) (PVC-U). The piping system is intended to be used for water supply and for buried and above-ground drainage and sewerage under pressure. In respect of potential adverse effects on the quality of water intended for human consumption, caused by the products covere
29、d by this part of ISO 1452, the following are relevant. a) This part of ISO 1452 provides no information as to whether or not the products can be used without restriction. b) Existing national regulations concerning the use and/or the characteristics of these products remain in force. Requirements a
30、nd test methods material and components, other than valves, are specified in ISO 1452-1, ISO 1452-2 and ISO 1452-3. Characteristics for fitness for purpose (mainly for joints) are covered in ISO 1452-5. This part of ISO 1452 covers the characteristics of valves. Guidance for installation is given in
31、 ISO/TR 41911. Guidance for assessment of conformity is provided in ENV 1452-72. For the convenience of users of this part of ISO 1452, marking on valves according to withdrawn International Standards (e.g. ISO 4422-4:1997) may be considered valid for a period, e.g. up to three years from the date o
32、f publication of this part of ISO 1452. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/03/2010 02:49, Uncontrolled Copy, (c) BSIBS EN ISO 1452-4:2009Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/03/2010 02:49, Uncontrolled Copy, (c) BSIBS EN ISO 1452-4:2009INTERNATIONAL STANDA
33、RD ISO 1452-4:2009(E) ISO 2009 All rights reserved 1Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 4: Valves 1 Scope This part of ISO 1452 specifies the characteristics of valves made from
34、unplasticized poly(vinyl chloride) (PVC-U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure. It also specifies the test parameters for the test methods referred to in this part of ISO 1452. In conjunction with ISO 1452-1, ISO 1452-2, I
35、SO 1452-3 and ISO 1452-5 it is applicable to PVC-U valves with components of PVC-U, other plastics and non-plastics materials intended to be used for the following: a) water mains and services buried in ground; b) conveyance of water above ground for both outside and inside buildings; c) buried and
36、above-ground drainage and sewerage under pressure. It is applicable to valves in piping systems intended for the supply of water under pressure up to and including 25 C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure. This part of ISO 14
37、52 is also applicable to valves for the conveyance of water and waste water up to and including 45 C. For temperatures between 25 C and 45 C, Figure A.1 of ISO 1452-2:2009 applies. NOTE 1 The producer and the end-user can come to agreement on the possibilities of use for temperatures above 45 C on a
38、 case-by-case basis. This part of ISO 1452 is applicable to valves of the following types: valves for solvent cementing; valves for elastomeric ring seal joints; valves for flanged joints. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these asp
39、ects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/03/2010 02:49, Uncontrolled Copy, (c) BSIBS EN ISO 1452-4:2009ISO 1452-4:2009(E) 2 ISO 2009 All rights reserved
40、2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 580, Plastics piping a
41、nd ducting systems Injection-moulded thermoplastics fittings Methods for visually assessing the effects of heating ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method ISO 1167-3, Thermoplas
42、tics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components ISO 1183-1:2004, Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titrat
43、ion method ISO 1452-1:2009, Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 1: General ISO 1452-2:2009, Plastics piping systems for water supply and for buried and above-ground drainage and
44、sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 2: Pipes ISO 1452-3:2009, Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 2: Fittings ISO 1452-5, Plastics piping syst
45、ems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 5: Fitness for purpose of the system ISO 2507-1:1995, Thermoplastics pipes and fittings Vicat softening temperature Part 1: General test method ISO 2507-2:1995, T
46、hermoplastics pipes and fittings Vicat softening temperature Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly(vinyl chloride) (PVC-HI) pipes ISO 3126, Plastics piping systems Plas
47、tics components Determination of dimensions ISO 7686, Plastics pipes and fittings Determination of opacity ISO 16135, Industrial valves Ball valves of thermoplastics materials ISO 16136, Industrial valves Butterfly valves of thermoplastics materials ISO 16137, Industrial valves Check valves of therm
48、oplastics materials ISO 16138, Industrial valves Diaphragm valves of thermoplastics materials ISO 16139, Industrial valves Gate valves of thermoplastics materials ISO 21787, Industrial valves Globe valves of thermoplastics materials EN 802, Plastics piping and ducting systems Injection-moulded therm
49、oplastics fittings for pressure piping systems Test method for maximum deformation by crushing Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 18/03/2010 02:49, Uncontrolled Copy, (c) BSIBS EN ISO 1452-4:2009ISO 1452-4:2009(E) ISO 2009 All rights reserved 33 Terms, definitions, symbols and abbreviated terms For the purposes of this document, the terms, definitions, symbols and abbreviated terms given in ISO 1452-1 apply. 4 Material 4.1 Valve bodies
