1、BSI Standards PublicationBS EN ISO 13225:2012Geometrical productspecifications (GPS) Dimensional measuringequipment; Height gauges Design and metrologicalcharacteristicsBS EN ISO 13225:2012Incorporating corrigendum October 2015BS EN ISO 13225:2012 BRITISH STANDARDNational forewordThis British Standa
2、rd is the UK implementation of EN ISO 13225:2012. It partially supersedes BS 1643:2008.The UK participation in its preparation was entrusted by Technical Committee TDW/4, Technical Product Realization, to Subcommittee TDW/4/4, Technical Product Realization - Gauging and Measurement Equipment.A list
3、of organizations represented on this subcommittee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards
4、 Limited 2015ISBN 978 0 580 92208 4ICS 17.040.30Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2012.Amendments/corrigenda issued since publicationDate T
5、ext affected31 October 2015 Supersession information in National foreword updatedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 13225 May 2012 ICS 17.040.30 English Version Geometrical product specifications (GPS) - Dimensional measuring equipment; Height gauges - Design and metrological c
6、haracteristics (ISO 13225:2012) Spcification gomtrique des produits (GPS) - quipement de mesurage dimensionnel; Mesureurs verticaux - Caractristiques de conception et caractristiques mtrologiques (ISO 13225:2012) Geometrische Produktspezifikation (GPS) - Lngenmessgerte: Vertikale Lngenmessgerte - Ko
7、nstruktionsmerkmale und messtechnische Merkmale (ISO 13225:2012) This European Standard was approved by CEN on 16 March 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard w
8、ithout any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any oth
9、er language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic,
10、 Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN
11、 DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 13225:2012: EBS EN ISO 13225:2012EN ISO 13225:2012 (E) 3 Foreword This d
12、ocument (EN ISO 13225:2012) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specifications and verification“ in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is
13、held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2012, and conflicting national standards shall be withdrawn at the latest by November 2012. Attention is drawn to the possib
14、ility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are
15、 bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spa
16、in, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 13225:2012 has been approved by CEN as a EN ISO 13225:2012 without any modification. BS EN ISO 13225:2012EN ISO 13225:2012 (E) 3 Foreword This document (EN ISO 13225:2012) has been prepared by Technical Commit
17、tee ISO/TC 213 “Dimensional and geometrical product specifications and verification“ in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status o
18、f a national standard, either by publication of an identical text or by endorsement, at the latest by November 2012, and conflicting national standards shall be withdrawn at the latest by November 2012. Attention is drawn to the possibility that some of the elements of this document may be the subje
19、ct of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bul
20、garia, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorseme
21、nt notice The text of ISO 13225:2012 has been approved by CEN as a EN ISO 13225:2012 without any modification. BS EN ISO 13225:2012EN ISO 13225:2012 (E) 3 Foreword This document (EN ISO 13225:2012) has been prepared by Technical Committee ISO/TC 213 “Dimensional and geometrical product specification
22、s and verification“ in collaboration with Technical Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text
23、 or by endorsement, at the latest by November 2012, and conflicting national standards shall be ithdrawn at the latest by November 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsi
24、ble for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland,
25、 France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 13225:2012 has been approved by CEN as a
26、 EN ISO 13225:2012 without any modification. BS EN ISO 13225:2012ISO 13225:2012(E) ISO 2012 All rights reserved iiiContents PageForeword ivIntroduction v1 Scope 12 Normative references . 13 Terms and definitions . 14 Design characteristics . 24.1 General design and nomenclature . 24.2 Main dimension
27、s . 54.3 Types of indicating devices 64.4 Protection for field use 104.5 Measuring and scribing stylus 104.6 Instrument base .104.7 Design characteristics (manufacturers specification) .105 Metrological characteristics . 115.1 General . 115.2 Operating conditions 115.3 Effect of slider locking . 115
28、.4 Definition of metrological characteristics (limited by MPE) 116 Proving of conformance with specifications .126.1 General .126.2 Measurement standards for the calibration of metrological characteristics 127 Marking .12Annex A (informative) Error tests .14Annex B (informative) Data sheet (Example)
29、 19Annex C (informative) Calibration of metrological characteristics .20Annex D (informative) Relation to the GPS matrix model 21Bibliography .23BS EN ISO 13225:2012ISO 13225:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodie
30、s (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations,
31、 governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/
32、IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the mem
33、ber bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 13225 was prepared by Technical Committee ISO/TC 213, Dimensional and ge
34、ometrical product specifications and verification.iv ISO 2012 All rights reservedBS EN ISO 13225:2012ISO 13225:2012(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Stand
35、ards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also ta
36、ke part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is
37、to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility
38、that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 13225 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification.iv ISO 2012 Al
39、l rights reservedBS EN ISO 13225:2012ISO 13225:2012(E)IntroductionThis International Standard is a geometrical product specification (GPS) standard and is to be regarded as a general GPS standard (see ISO/TR 14638). It influences the chain link 5 of the chain of standards on size and distance.The IS
40、O/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this document is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this document and the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this document
41、, unless otherwise indicated.For more detailed information of the relation of this International Standard to the GPS matrix model, see Annex D.This International Standard is intended to serve the purpose of promoting the relationship between the manufacturer and purchaser, and the management of meas
42、uring instruments in the quality-assurance system. ISO 2012 All rights reserved vBS EN ISO 13225:2012BS EN ISO 13225:2012 BS EN ISO 13225:2012Geometrical product specifications (GPS) Dimensional measuring equipment; Height gauges Design and metrological characteristics1 ScopeThis International Stand
43、ard specifies the most important design and metrological characteristics of height gauges (with analogue indication or digital indication) for linear-dimensional measurements perpendicular to a surface plate.2 Normative referencesThe following referenced documents are indispensable for the applicati
44、on of this document. For dated references, only the cited editions apply. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 1:2002, Geometrical Product Specifications (GPS) Standard reference temperature for geometrical product specification
45、 and verificationISO 14253-1, Geometrical product specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 1: Decision rules for proving conformance or non-conformance with specificationsISO 14253-2, Geometrical product specifications (GPS) Inspection by measurement
46、of workpieces and measuring equipment Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verificationISO 14978:2006, Geometrical product specifications (GPS) General concepts and requirements for GPS measuring equipmentIEC 6052
47、9, Degrees of protection provided by enclosures (IP Code)ISO/IEC Guide 98-3, Uncertainty of measurement Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)ISO/IEC Guide 99, International vocabulary of metrology Basic and general concepts and associated terms (VIM)3 Terms and def
48、initionsFor the purposes of this document, the terms and definitions given in ISO 14978, ISO/IEC Guide 99 and the following apply.3.1height gaugemeasuring instrument in which a slider with a measuring stylus moves relative to a measuring scale on a beam and in which this motion is along a single ver
49、tical axis nominally perpendicular to a reference plane on the instrument baseNOTE 1 Height gauges are designed to be used with surface plates in which the reference plane of the height gauge is placed in contact with the surface plate.NOTE 2 Various types of measuring scales on the beam with appropriate indication are possible, such as analogue indication, including vernier and circular scales, and digital indication.NOTE 3 Most height gauges are capable of using various types of measuring styli, including a scriber.INTERNATIONA
