1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN ISO 14526-3:2000 Th
2、e European Standard EN ISO 14526-3:1999 has the status of a British Standard ICS 83.080.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Plastics Phenolic powder moulding compounds (PF-PMCs) Part 3: Requirements for selected moulding compoundsThis British Standard, having be
3、en prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 January 2000 BSI 01-2000 ISBN 0 580 35875 5 BS EN ISO 14526-3:2000 Amendments issued since publication Amd. No. Date Comments
4、National foreword This British Standard is the English language version of EN ISO 14526-3:1999. It is identical with ISO 14526-3:1999. The UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the responsibili
5、ty to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of
6、organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresponding European publicati
7、ons. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard
8、 does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an
9、inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 6, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued.EN ISO 14526-3:1999 Referencen
10、umber ISO14526-3:1999(E) INTERNATIONAL STANDARD ISO 14526-3 Firstedition 1999-11-15 PlasticsPhenolicpowdermoulding compounds(PF-PMCs) Part3: Requirementsforselectedmoulding compounds Plastiques Poudres mouler phnoliques (PF-PMC) Partie 3: Exigences relatives certaines poudres mouler EN ISO 14526-3:1
11、999ISO-625413:(9991E) ISO9991 Allrgihtsresvrede.lnUesstorehwisescepfieid,noraptofthisilbupctaoinmaybeudorpercedorutziliedinnayformorbynaysnaem,electnoric ormecinahcal,inclidungtohpociypongnadmicrfoilm,wituohteprmissioninwritingfromeitehrISOattheerddassbleoworISOsmemebrydob inthectnuoryofthertseuqee.
12、r ISOcirypohgtfofice aCsesoptale56 121-HC1veneGa20 leT.+41224790111 aFx+41223741097 E-mailcirypothgiso.ch Webwww.iso.ch ii DPFdcsilremia ihTsPDFfilemayctnoainemeddebdtyfepaces.InaccnadrocewithAebodslicensinglopicy,thisfilemaybepirntedorivewedubtslahlton beidetedlnuessthetyfepaceswhichareemeddebdrael
13、icensedtonadintslaledonthecomputerfrepormingtheideting.Inodwlnidaongthis feli,trapiesaccepttierehnthesersnoptilibiyofontinfrnignigAebodslicsneniglopicy.hTeISOtneCarlSecterairatacceptsnollibaiityinthis .aera AbodeisatdaremarkofAbodeStsyemsInctaropro.de teDailsofthesfotwraepudorctsusedtocrtaeetihsPDFf
14、ilecanbefnuodintheGarenelInfolerativetothefile;theP-FDcerationrapamteers weretpoimizedforpirtning.EvreycraeahseebntakentoensruethatthefileisiustlbaeforusebyISOmemebridobse.Inthelnuikleyetnev tahtaplboremleratingtoitisfdnuo,lpaeseifnormthetneCarlSecterairatattheserddasgivenlebow. EN ISO 14526-3:1999I
15、SO14526-3:1999(E)iii Foreword ISO(theInternationalOrganizationforStandardization)isaworldwidefederationofnationalstandardsbodies(ISO memberbodies).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnical committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteeh
16、asbeenestablishedhas therighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnon-governmental,in liaisonwithISO,alsotakepartinthework.ISOcollaboratescloselywiththeInternationalElectrotechnical Commission(IEC)onallmattersofelectrotechnicalstandardization. InternationalStandar
17、dsaredraftedinaccordancewiththerulesgivenintheISO/IECDirectives,Part3. DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtothememberbodiesforvoting. PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiescastingavote. Attentionisdrawntothepossibilitytha
18、tsomeoftheelementsofthispartofISO14526maybethesubjectof patentrights.ISOshallnotbeheldresponsibleforidentifyinganyorallsuchpatentrights. InternationalStandardISO14526-3waspreparedbyTechnicalCommitteeISO/TC61, Plastics, Subcommittee SC12, Thermosetting materials. Afteratransitionperiodof,atthemost,fo
19、uryears,thethreepartsofISO14526(seebelow)willreplace ISO800:1992,ofwhichtheyconstituteatechnicalrevision. ISO14526consistsofthefollowingparts,underthegeneraltitle Plastics Phenolic powder moulding compounds (PF-PMCs): Part 1: Designation system and basis for specifications Part 2: Preparation of tes
20、t specimens and determination of properties Part 3: Requirements for selected moulding compounds AnnexAofthispartofISO14526isforinformationonly. EN ISO 14526-3:1999EN ISO 14526-3:1999INTERNATIONAL STANDARD ISO 14526-3:1999(E) ISO 9991 All irhgts seredevr 1 Plastics Phenolic powder moulding compounds
21、 (PF-PMCs) Part 3: Requirements for selected moulding compounds 1 Scope This part of ISO 14526 specifies the requirements for the physical and chemical properties of phenolic powder moulding compounds (PF-PMCs) and compression- or injection-moulded test specimens produced from them. It is limited to
22、 those powder moulding compounds whose composition and properties are significantly different. It is further limited to those moulding compounds which are of general technical and/or economic importance. The properties which are used to characterize the moulding compounds, the test methods and the t
23、est conditions are selected from those given in ISO 14526-2. The moulding compounds are divided into types according to their composition and properties. The various types are designated using the designation system defined in ISO 14526-1. 2 Normative references The following normative documents con
24、tain provisions which, through reference in this text, constitute provisions of this part of ISO 14526. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 14526 are encouraged to investigat
25、e the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 472:1999, Plastics Vo
26、cabulary. ISO 800:1992, Plastics Phenolic moulding materials Specification. ISO 14526-1:1999, Plastics Phenolic powder moulding compounds (PF-PMCs) Part 1: Designation system and basis for specifications. ISO 14526-2:1999, Plastics Phenolic powder moulding compounds (PF-PMCs) Part 2: Preparation of
27、test specimens and determination of properties. 3 Terms and definitions For the purposes of this part of ISO 14526, the terms and definitions given in ISO 472, ISO 14526-1 and ISO 14526-2 apply. EN ISO 14526-3:1999 1ISO -625413:(9991E) 2 ISO 9991 All irhgts seredevr 4 Requirements 4.1 Property value
28、s In order for a phenolic powder moulding compound to be considered as complying with this part of ISO 14526, it shall meet the requirements given in the appropriate table (Table 1, 2 or 3). Tables 1, 2 and 3 give the mean value obtained for the set of test specimens used to determine a particular p
29、roperty. Individual values of properties 2.1, 2.2, 2.3 and 2.4 shall be within 10 % of the mean value, and individual values of properties 3.1 and 3.2 shall be within 5 C of the mean value. No specific limits are placed on rheological and processing properties. However, suitable rheological and proc
30、essing properties are essential for the satisfactory use of a moulding compound. The test methods and test conditions used shall be as agreed between the interested parties. In addition, for some applications, it may be useful for information to be made available on other properties, for example: cu
31、re time; particle size; moisture content. If this is so, these properties and test methods, as well as the test conditions to be used, shall be as agreed between the interested parties. 4.2 Filler/reinforcement type and content In order for a phenolic powder moulding compound to be considered as com
32、plying with this part of ISO 14526, the nature, form and content by mass of its filler/reinforcement shall be as given in the designation of the moulding compound (see ISO 14526-1:1999, subclause 4.2). EN ISO 14526-3:1999 2ISO -625413:(9991E) ISO 9991 All irhgts seredevr 3 Table 1 Property requireme
33、nts for PF-PMCs containing (WD+MD) or (LF+MD) as filler 1234 Type: PMC ISO 14526-PF. . . Property Unit Pro- cess- ing a Max. or min. (WD30+MD20) to (WD40+MD10) (WD30+MD20),X,E to (WD40+MD10),X,E (WD30+MD20),X,A to (WD40+MD10),X,A (LF20+MD25) to (LF30+MD15) 1 Rheological and processing properties 1.1
34、 To be agreed between the interested parties 2 Mechanical properties 2.1 Stress at break, B MPa Q M W W 40 50 40 50 40 50 40 50 2.2 Flexural strength, fM MPa Q M W W 70 80 70 80 70 80 70 80 2.3 Charpy impact strength, a cU kJ/m 2 Q M W W 4,5 5,0 4,5 5,0 4,5 5,0 4,5 5,0 2.4 Charpy notched impact stre
35、ngth, a cA kJ/m 2 Q M W W 1,3 1,3 1,3 1,3 1,3 1,3 2,5 2,5 3 Thermal properties 3.1 Temperature of deflection under load, T f 1,8 C Q/M W 160 160 160 160 3.2 Temperature of deflection under load, T f 8,0 C Q/M W 115 115 115 110 3.3 Flammability (glow bar), BH Q / Mu BH 2-10 BH 2-10 BH 2-10 BH 2-30 4
36、Electrical properties 4.1 Dissipation factor, tan 100 Q / Mu 0 , 1 4.2 Volume resistivity, e cm Q/M W 1 0 11 4.3 Surface resistivity, e Q/M W 10 9 10 10 10 9 10 8 4.4 Proof tracking index, PTI Q/M W 125 125 125 125 5 Other properties 5.1 mg u 100 100 100 150 5.2 Water absorption, W w 24 %b y mass Q/
37、M u 5.3 Free ammonia, m E AM %b y mass Q/M u 0,02 a Q = Compression moulding M = Injection moulding NOTE 1 See ISO 14526-2:1999, Tables 3 and 4, columns 3, 4, and 7, for the methods to be used for the preparation of test specimens and the determination of properties. NOTE 2 In view of the difference
38、s between the property-value limits for compression-moulding and injection-moulding materials, the likely variations in test results and the wide range of properties covered, it should not be assumed that materials having the same designation are exactly equivalent. EN ISO 14526-3:1999 3ISO -625413:
39、(9991E) 4 ISO 9991 All irhgts seredevr Table 2 Property requirements for PF-PMCs containing (SC+LF), SS, PF or (LF+MD) as filler 5678 Type: PMC ISO 14526-PF. . . Property Unit Pro- cess- ing a Max. or min. (SC20+LF15) to (SC30+LF05) SS40 to SS50 PF40 to PF60 (LF20+MD25) to (LF40+MD05) 1 Rheological
40、and processing properties 1.1 To be agreed between the interested parties 2 Mechanical properties 2.1 Stress at break, B MPa Q M W W 35 45 30 45 30 40 35 45 2.2 Flexural strength, fM MPa Q M W W 70 80 60 70 50 60 70 80 2.3 Charpy impact strength, a cU kJ/m 2 Q M W W 5,5 6,5 7,0 9,0 2,5 3,5 5,5 6,0 2
41、.4 Charpy notched impact strength, a cA kJ/m 2 Q M W W 4,0 4,0 7,0 7,0 1,5 1,5 2,8 2,8 3 Thermal properties 3.1 Temperature of deflection under load, T f 1,8 C Q/M W 160 160 170 160 3.2 Temperature of deflection under load, T f 8,0 C Q/M W 110 115 130 115 3.3 Flammability (glow bar), BH Q / Mu BH 2-
42、30 BH 2-30 BH 1 BH 2-30 4 Electrical properties 4.1 Dissipation factor, tan 100 Q / Mu 0 , 1 4.2 Volume resistivity, e cm Q/M W 1 0 12 4.3 Surface resistivity, e Q/M W 10 8 10 8 10 11 10 8 4.4 Proof tracking index, PTI Q/M W 125 125 175 125 5 Other properties 5.1 mg u 150 200 30 150 5.2 Water absorp
43、tion, W w 24 %b y mass Q/M u 5.3 Free ammonia, m E AM %b y mass Q/M u a Q = Compression moulding M = Injection moulding NOTE 1 See ISO 14526-2:1999, Tables 3 and 4, columns 3, 4, and 7, for the methods to be used for the preparation of test specimens and the determination of properties. NOTE 2 In vi
44、ew of the differences between the property-value limits for compression-moulding and injection-moulding materials, the likely variations in test results and the wide range of properties covered, it should not be assumed that materials having the same designation are exactly equivalent. EN ISO 14526-
45、3:1999 4ISO -625413:(9991E) ISO 9991 All irhgts seredevr 5 Table 3 Property requirements for PF-PMCs containing (GF+GG) or (GF+MD) as filler 91 01 11 2 Type: PMC ISO 14526-PF. . . Property Unit Pro- cess- ing a Max. or min. (GF20+GG30) to (GF30+GG20) (GF30+MD20) to (GF40+MD10) 1 Rheological and proc
46、essing properties 1.1 To be agreed between the interested parties 2 Mechanical properties 2.1 Stress at break, B MPa Q M W W 50 60 80 90 2.2 Flexural strength, fM MPa Q M W W 80 90 140 150 2.3 Charpy impact strength, a cU kJ/m 2 Q M W W 6,0 7,0 13,0 15,0 2.4 Charpy notched impact strength, a cA kJ/m
47、 2 Q M W W 1,5 1,5 3,0 3,5 3 Thermal properties 3.1 Temperature of deflection under load, T f 1,8 C Q/M W 190 210 3.2 Temperature of deflection under load, T f 8,0 C Q/M W 140 160 3.3 Flammability (glow bar), BH Q / Mu BH 1 BH 1 4 Electrical properties 4.1 Dissipation factor, tan 100 Q / Mu 0,25 0,2
48、5 4.2 Volume resistivity, e cm Q/M W 10 11 10 12 4.3 Surface resistivity, e Q/M W 10 10 10 11 4.4 Proof tracking index, PTI Q/M W 175 150 5 Other properties 5.1 mg u 30 30 5.2 Water absorption, W w 24 %b y mass Q/M u 5.3 Free ammonia, m E AM %b y mass Q/M u a Q = Compression moulding M = Injection m
49、oulding NOTE 1 See ISO 14526-2:1999, Tables 3 and 4, columns 3, 4, and 7, for the methods to be used for the preparation of test specimens and the determination of properties. NOTE 2 In view of the differences between the property-value limits for compression-moulding and injection-moulding materials, the likely variations in test results and the wide range of properties covered, it should not be assumed
