1、BSI Standards PublicationBS EN ISO 16396-1:2015Plastics Polyamide (PA)moulding and extrusionmaterialsPart 1: Designation system, marking ofproducts and basis for specificationsBS EN ISO 16396-1:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN ISO 16396-1:201
2、5. It supersedes BS EN ISO 1874-1:2010 which iswithdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/82, Thermoplastic materials.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to
3、 include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 74191 3 ICS 83.080.20 Compliance with a British Standard cannot confer immunity from legal obligations.
4、This British Standard was published under the authority of the Standards Policy and Strategy Committee on 28 February 2015.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 16396-1 February 2015 ICS 83.080.20 Supersedes
5、 EN ISO 1874-1:2010English Version Plastics - Polyamide (PA) moulding and extrusion materials - Part 1: Designation system, marking of products and basis for specifications (ISO 16396-1:2015) Plastiques - Matriaux polyamides (PA) pour moulage et extrusion - Partie 1: Systme de dsignation, marquage d
6、esproduits et base de spcification (ISO 16396-1:2015) Kunststoffe - Polyamid (PA)-Formmassen fr das Spritzgieen und die Extrusion - Teil 1: Bezeichnungssystem, Produktkennzeichnung und Basis fr Spezifikationen (ISO 16396-1:2015) This European Standard was approved by CEN on 26 December 2014. CEN mem
7、bers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicat
8、ion to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Manage
9、ment Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
10、 Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix
11、17, B-1000 Brussels 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 16396-1:2015 EBS EN ISO 16396-1:2015Foreword This document (EN ISO 16396-1:2015) has been prepared by Technical Committee ISO/TC 61 “Plastics” in collabor
12、ation with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2015, and conflicting national standards shall
13、be withdrawn at the latest by August 2015. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN ISO 1874-1:2010
14、. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, G
15、ermany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. Endorsement notice The text of ISO 16396-1:2015 has been approved by CEN as EN ISO 16
16、396-1:2015 without any modification. EN ISO 16396-1:2015 (E)BS EN ISO 16396-1:2015ISO 16396-1:2015(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Designation system 23.1 General . 23.2 Data block 1 . 33.3 Data block 2 . 53.4 Data block 3 . 63.5 Data block 4 . 73.5.1 General 73.5.2 V
17、iscosity number . 73.5.3 Tensile modulus of elasticity . 93.6 Data block 5 104 Examples of designations .104.1 Designations without specification 104.2 Designation transformed into a specification . 12Annex A (normative) Definition and designation of polyamides 14Bibliography .16 ISO 2015 All rights
18、 reserved iiiContents PageBS EN ISO 16396-1:2015ISO 16396-1:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical
19、committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with
20、the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for
21、 the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.
22、 ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this d
23、ocument is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Tr
24、ade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic materials.This first edition of ISO 16396-1 cancels and replaces ISO 1874-1:2010, which has been technically revised to introduce
25、a new designation system.The revised designation system is published under a new ISO number, as many existing documents refer to ISO 1874-1. If the existing ISO 1874-1 would be replaced by the new designation system, these documents would refer to the incorrect designation system.In order to give us
26、ers time to switch from ISO 1874-1 to ISO 16396-1, any designation system according to ISO 1874-1 is to be phased out in 5 to 10 years. During this period, ISO 1874-2 will effectively be Part 2 of this International Standard.ISO 16396 consists of the following parts, under the general Plastics Polym
27、ide (PA) moulding and extrusion materials: Part 1: Designation system, marking of products and basis for specificationiv ISO 2015 All rights reservedBS EN ISO 16396-1:2015ISO 16396-1:2015(E)IntroductionISO 1874-1:2010 is complex and does not fit with daily practice anymore. In practice, ISO 1043 and
28、 ISO 11469 are, in combination, improperly being used as a designation system for, e.g. marking. The aim of this International Standard is to simplify the data block system and to connect more to ISO 1043 and ISO 11469, where the first two blocks are used for generic identification and marking of pr
29、oducts. ISO 2015 All rights reserved vBS EN ISO 16396-1:2015BS EN ISO 16396-1:2015Plastics Polyamide (PA) moulding and extrusion materials Part 1: Designation system, marking of products and basis for specifications1 ScopeThis part of ISO 16396 establishes a system of designation for polyamide (PA)
30、moulding and extrusion materials, which can be used as the basis for specifications.The types of polyamide plastics are differentiated from each other by a classification system based on appropriate levels of the designatory propertiesa) viscosity number andb) tensile modulus of elasticityand on inf
31、ormation about composition, intended application and/or method of processing, important properties, additives, colorants, fillers, and reinforcing materials.The designation system is applicable to all polyamide homopolymers, copolymers, and blends.It applies to unmodified materials ready for normal
32、use and materials modified, for example, by colorants, additives, fillers, reinforcing materials, and polymer modifiers.This part of ISO 16396 does not apply to the following materials:a) monomer casting-type polyamides of PA 6;b) monomer casting-type polyamides of PA 12.It is not intended to imply
33、that materials having the same designation give the same performance. This part of ISO 16396 does not provide engineering data, performance data, or data on processing conditions which can be required to specify a material. If such additional properties are required, they will be determined in accor
34、dance with the test methods specified in ISO 1874-2, if suitable.In order to designate a thermoplastic material to meet particular specifications, the requirements are to be given in data block 5 (see 3.1).2 Normative referencesThe following documents, in whole or in part, are normatively referenced
35、 in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 307, Plastics Polyamides Determination of viscosity numberISO 1043-1:2011, P
36、lastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristicsISO 1874-2, Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of propertiesINTERNATIONAL STANDARD ISO 16396-1:2015(E) ISO 2015 All rights reser
37、ved 1BS EN ISO 16396-1:2015ISO 16396-1:2015(E)3 Designation system3.1 GeneralThe designation system for thermoplastics is based on the following standard pattern:DesignationDescription blockIdentity blockInternational Standard BlockIndividual item blockThermoplastics(optional)Datablock1Databloc k2Da
38、tablock3Datablock4Datablock5Figure 1 Data block designation systemThe designation consists of an optional description block, reading “Thermoplastics”, and an identity block comprising the International Standard number and an individual-item block. For unambiguous designation, the individual-item blo
39、ck is subdivided into five data blocks comprising the following information.Data block 1: Position 1: Identification of the plastic by its abbreviated term (PA), in accordance with ISO 1043-1 and information about the composition of the polymer.Position 2: Information on the use of plasticizer (P) o
40、r impact modifier (I) (see 3.2).Data block 2: Position 1: Fillers or reinforcements and their nominal content.Position 2: Flame retardant information.Position 3: Declaration of recyclate (R) (see 3.3).Data block 3: Position 1: Intended application and/or method of processing.Positions 2 to 8: Import
41、ant properties, additives, and supplementary information (see 3.4).Data block 4: Designatory properties (see 3.5).Data block 5: For the purpose of specification, the fifth data block contains appropriate informa-tion (see 3.6).The first character of the individual-item block shall be a hyphen. The d
42、ata blocks shall be separated from each other by commas.If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (). Terminal commas can be omitted.NOTE Data blocks 1 and 2 together form the part marking symbol, connected with a hyphen, and placed betw
43、een the punctuation marks and Part markingPA 6-P-(GF+MD)25FR(30)(R50)90 to 110110 to 130130 to 160160 to 200200 to 240240 to 290290 to 340340PA 6,PA 66,PA 69,PA 610,PA 612,PA 613,PA MXD6 andcopolyamidesC11C12C14C16C18C22C24110110 to 130130 to 150150 to 170170 to 200200 to 240240PA 1010,PA 1012,PA 12
44、12,PA 11,PA 12 andcopolyamidesP12P13P15P17P19P20120120 to 140140 to 160160 to 180180 to 200200PA 6T/66, PA 6I/66, PA 6I/6T, PA 6T/6I/66, PA 6T/6I, PA 10T PA 6I/6T/66, PPA and copolyamidesNOTE Viscosity numbers determined with 90 % (m/m) formic acid as solvent can be converted into viscosity numbers
45、determined in 96 % (m/m) sulfuric acid using the following formulae, in accordance with ISO 307:For PA 6: In y = 0,416 1 + 0,927 6 In xFor PA 66: In y = 0,454 1 + 0,926 1 In XFor PA 69: In y = 0,463 4 + 0,909 5 In xFor PA 610: In y = 0,982 3 + 0,793 2 In xwherex is the viscosity number in 90 % (m/m)
46、 formic acid;y is the viscosity number in 96 % (m/m) sulfuric acid.For the viscosity number of PA 612, which can be determined in accordance with ISO 307 in either m-cresol or 96 % (m/m) sulfuric acid, the following conversion formula applies:ln y = 0,285 7 + 0,985 9 ln x8 ISO 2015 All rights reserv
47、edBS EN ISO 16396-1:2015ISO 16396-1:2015(E)wherex is the viscosity number in 96 % (m/m) sulfuric acid;y is the viscosity number in m-cresol.These conversion formulae have been calculated from the results of an interlaboratory investigation carried out in 1982 (ISO 307). The accuracy of the conversio
48、ns depends on both the size of the viscosity number and the type of PA, the latter resulting from the fact that different numbers of the different PA-types were included in the investigation. The 95 % confidence intervals for the values of the nominal viscosity number in 96 % (m/m) sulfuric acid, co
49、nverted from different values of the nominal viscosity number in the other solvent, are given in Table 6.Table 6 Confidence intervalsNominal viscosity numbera95 % confidence intervals for converted nominal viscosity numbers in 96 % (m/m) sulfuric acidPA 6 PA 66 PA 69 PA 610 PA 6121001401802202603003400,80,80,70,70,81,01,31,61,41,21,31,72,43,32,01,92,94,76,99,311,94,74,15,89,012,917,221,84.44,910,217,626,035,345,3aSolvents: 90 % (m/m) formic acid for PA 6, PA 66, PA 69, and PA
