1、BS EN ISO22391-3:2009ICS 23.040.45; 91.140.60; 93.025NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPlastics piping systemsfor hot and coldwater installations Polyethylene of raisedtemperature resistance(PE-RT)Part 3: Fittings (ISO 22391-3:2009)Licensed Copy: W
2、ang Bin, ISO/EXCHANGE CHINA STANDARDS, 07/04/2010 04:07, Uncontrolled Copy, (c) BSIThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 31 January2010 BSI 2010ISBN 978 0 580 60047 0Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 2
3、2391-3:2009National forewordThis British Standard is the UK implementation of EN ISO22391-3:2009.The UK participation in its preparation was entrusted to TechnicalCommittee PRI/88/2, Plastics piping for pressure applications.A list of organizations represented on this committee can be obtained onreq
4、uest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 07/04
5、/2010 04:07, Uncontrolled Copy, (c) BSIEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 22391-3 December 2009 ICS 23.040.45; 91.140.60; 93.025 English Version Plastics piping systems for hot and cold water installations - Polyethylene of raised temperature resistance (PE-RT) - Part 3: Fittin
6、gs (ISO 22391-3:2009) Systmes de canalisations en plastique pour les installations deau chaude et froide - Polythylne de meilleure rsistance la temprature (PE-RT) - Partie 3: Raccords (ISO 22391-3:2009) Kunststoff-Rohrleitungssysteme fr die Warm- und Kaltwasserinstallation - Polyethylen erhhter Temp
7、eraturbestndigkeit (PE-RT) - Teil 3: Formstcke (ISO 22391-3:2009) This European Standard was approved by CEN on 4 November 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standar
8、d without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other la
9、nguage made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Fin
10、land, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES
11、KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 22391-3:2009: ELicensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 07/04/2010 04:07, Uncontrolled C
12、opy, (c) BSIBS EN ISO 22391-3:2009EN ISO 22391-3:2009 (E) 3 Foreword This document (EN ISO 22391-3:2009) has been prepared by Technical Committee ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids“ in collaboration with Technical Committee CEN/TC 155 “Plastics piping systems
13、 and ducting systems” the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national standards shall be withdrawn at the latest by Jun
14、e 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards orga
15、nizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, R
16、omania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 22391-3:2009 has been approved by CEN as a EN ISO 22391-3:2009 without any modification. Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 07/04/2010 04:07, Uncontrolled Copy, (c) B
17、SIBS EN ISO 22391-3:2009ISO 22391-3:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword iv Introduction.v 1 Scope1 2 Normative references1 3 Terms, definitions, symbols and abbreviated terms .2 3.1 General fittings 2 3.2 Mechanical fittings 3 3.3 Fittings for heat fusion3 4 Material chara
18、cteristics.3 4.1 Plastics fitting material .3 4.2 Metallic fitting material5 4.3 Influence on water intended for human consumption 5 5 General characteristics.5 5.1 Appearance 5 5.2 Opacity6 6 Geometrical characteristics .6 6.1 General .6 6.2 Dimensions of sockets for socket fusion and electrofusion
19、 fittings.6 6.3 Dimensions of metallic fittings 9 7 Mechanical characteristics of plastics fittings.10 7.1 General .10 7.2 Fitting material identical to PE-RT compound .10 7.3 Fitting made from PE-RT but not identical to PE-RT compound10 7.4 Fittings made from plastics other than PE-RT .10 8 Physica
20、l and chemical characteristics of plastics components 12 8.1 Melt mass flow rate .12 9 Sealing elements .12 10 System performance requirements .12 11 Marking.12 11.1 General requirements .12 11.2 Minimum required marking 12 Bibliography14 Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 07/04/
21、2010 04:07, Uncontrolled Copy, (c) BSIBS EN ISO 22391-3:2009ISO 22391-3:2009(E) iv ISO 2009 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards i
22、s normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take par
23、t in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to p
24、repare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility tha
25、t some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 22391-3 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2
26、, Plastics pipes and fittings for water supplies. This second edition cancels and replaces the first edition (ISO 22391-3:2007), which is extended from only dealing with PE-RT material (referred to as Type I) to cover PE-RT materials Type I and Type II. ISO 22391 consists of the following parts1), u
27、nder the general title Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT): Part 1: General Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system 1) This System Standard does not incorporate a Part 4: Ancillary equipme
28、nt or a Part 6: Guidance for installation. For ancillary equipment, separate standards can apply. Guidance for installation of plastics piping systems made from different materials, intended to be used for hot and cold water installations, is covered by ENV 12108. Licensed Copy: Wang Bin, ISO/EXCHAN
29、GE CHINA STANDARDS, 07/04/2010 04:07, Uncontrolled Copy, (c) BSIBS EN ISO 22391-3:2009ISO 22391-3:2009(E) ISO 2009 All rights reserved vIntroduction The System Standard, of which this is Part 3, specifies the requirements for a piping system and its components when made from polyethylene of raised t
30、emperature resistance (PE-RT). The piping system is intended to be used for hot and cold water installations. In respect of potential adverse effects on the quality of water intended for human consumption caused by the products covered by ISO 22391, the following are relevant. a) This part of ISO 22
31、391 provides no information as to whether the products can be used without restriction. b) Existing national regulations concerning the use and/or characteristics of the products remain in force. This part of ISO 22391 specifies the general aspects of the plastics piping system. At the date of publi
32、cation of this part of ISO 22391, System Standards Series for piping systems of other plastics materials used for the same application are the following: ISO 15874 (all parts), Plastics piping systems for hot and cold water installations Polypropylene (PP) ISO 15875 (all parts), Plastics piping syst
33、ems for hot and cold water installations Crosslinked polyethylene (PE-X) ISO 15876 (all parts), Plastics piping systems for hot and cold water installations Polybutylene (PB) ISO 15877 (all parts), Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C)
34、Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 07/04/2010 04:07, Uncontrolled Copy, (c) BSIBS EN ISO 22391-3:2009Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 07/04/2010 04:07, Uncontrolled Copy, (c) BSIBS EN ISO 22391-3:2009INTERNATIONAL STANDARD ISO 22391-3:2009(E) ISO 2009 All ri
35、ghts reserved 1Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 3: Fittings 1 Scope This part of ISO 22391 specifies the characteristics of fittings for piping systems made of polyethylene of raised temperature resistance (PE-RT)
36、, Type I, and polyethylene of raised temperature resistance (PE-RT), Type II, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not the water is intended for human consumption (domestic systems) and for heating systems, under the design
37、 pressures and temperatures appropriate to the class of application according to ISO 22391-1. This part of ISO 22391 covers a range of service conditions (classes of application), design pressures and pipe dimension classes, and also specifies test parameters and test methods. In conjunction with th
38、e other parts of ISO 22391, it is applicable to fittings made of PE-RT, as well as to those made of other materials, intended to be fitted to pipes conforming to ISO 22391-2 for hot and cold water installations, the joints of which are in accordance with ISO 22391-5. This part of ISO 22391 is applic
39、able to the following types of fitting: mechanical fittings; socket fusion fitting; electrofusion fittings; fittings with incorporated inserts. It is not applicable to values of design temperature, maximum design temperature or malfunction temperature in excess of those specified in ISO 22391-1. NOT
40、E It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. 2 Normative references The following referenced documents are i
41、ndispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7-1, Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensi
42、ons, tolerances and designation Licensed Copy: Wang Bin, ISO/EXCHANGE CHINA STANDARDS, 07/04/2010 04:07, Uncontrolled Copy, (c) BSIBS EN ISO 22391-3:2009ISO 22391-3:2009(E) 2 ISO 2009 All rights reservedISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimension
43、s, tolerances and designation ISO 1133-1, Plastics Determination of the melt volume-flow rate (MVR) and the melt mass-flow rate (MFR) of thermoplastics Part 1: Standard method ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to in
44、ternal pressure Part 1: General method ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces ISO 3126, Plastics piping systems Plastics components Determination of dimensions
45、 ISO 7686, Plastics pipes and fittings Determination of opacity ISO 9080, Plastics piping and ducting systems Determination of long-term hydrostatic strength of thermoplastic materials in pipe form by extrapolation ISO 23711, Elastomeric seals Requirements for materials for pipe joint seals used in
46、water and drainage applications Thermoplastic elastomers ISO 22391-1:2009, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 1: General ISO 22391-2:2009, Plastics piping systems for hot and cold water installations Polyethylene of
47、 raised temperature resistance (PE-RT) Part 2: Pipes ISO 22391-5, Plastics piping systems for hot and cold water installations Polyethylene of raised temperature resistance (PE-RT) Part 5: Fitness for purpose of the system EN 681-1, Elastomeric seals Materials requirements for pipe joint seals used
48、in water and drainage applications Part 1: Vulcanized rubber EN 681-2, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elastomers EN 1254-3, Copper and copper alloys Plumbing fittings Part 3: Fittings with compression ends f
49、or use with plastics pipes EN 10088-1, Stainless steels Part 1: List of stainless steels 3 Terms, definitions, symbols and abbreviated terms For the purposes of this document, the terms, definitions, symbols and abbreviated terms given in ISO 22391-1 and the following apply. 3.1 General fittings 3.1.1 fitting component of a piping system, which connects two or more pipes and/or fittings together, without any additional function Licensed Copy: Wang Bin, ISO/EXCHANGE
