1、Metallic cables and other passive components test methodsPart 4-6: Electromagnetic compatibility (EMC) - Surface transfer impedance - Line injection methodBS IEC 62153-4-6:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06IEC 62153-4-6 Edition 2.0 2017-08 INTERNATI
2、ONAL STANDARD Metallic cables and other passive components test methods Part 4-6: Electromagnetic compatibility (EMC) Surface transfer impedance Line injection method IEC62153-4-6:2017-08(en) National forewordThis British Standard is the UK implementation of IEC 62153-4-6:2017.The UK participation i
3、n its preparation was entrusted to Technical Committee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport
4、 to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017ISBN 978 0 580 89908 9ICS 33.120.10Compliance with a British Standard cannot confer immunity from legal obligations
5、. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2017.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS IEC 6215346:2017IEC 62153-4-6 Edition 2.0 2017-08 INTERNATIONAL STANDARD Metallic cables an
6、d other passive components test methods Part 4-6: Electromagnetic compatibility (EMC) Surface transfer impedance Line injection method IEC62153-4-6:2017-08(en) BS IEC 6215346:2017THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2017 IEC, Geneva, Switzerland All rights reserved. Unless otherwise spe
7、cified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions ab
8、out IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec
9、.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publication
10、s is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Stan
11、dards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It
12、also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electrope
13、dia.org The worlds leading online dictionary of electronic and electrical terms containing 20 000 terms and definitions in English and French, with equivalent terms in 16 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossar
14、y 65 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If y
15、ou wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. BS IEC 6215346:2017THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2017 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this
16、publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or hav
17、e an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.
18、ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant
19、 review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographical information on IEC International Standards, Technical Specifi
20、cations, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information o
21、n projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leadi
22、ng online dictionary of electronic and electrical terms containing 20 000 terms and definitions in English and French, with equivalent terms in 16 additional languages. Also known as the International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary 65 000 electrotechnica
23、l terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your
24、feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 62153-4-6 Edition 2.0 2017-08 INTERNATIONAL STANDARD Metallic cables and other passive components test methods Part 4-6: Electromagnetic compatibility (EMC) Surface transfer impedance
25、Line injection method INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 33.120.10 ISBN 978-2-8322-4748-8 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. BS IEC 6215346:2017 2 IEC 62153-4-6:2017 IE
26、C 2017 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Terms and definitions 5 4 Physical background 5 5 Test set-up 6 5.1 General . 6 5.2 Equipment 7 5.3 Injection feature 7 5.4 Impedance of inner circuit . 10 6 Preparation of the test sample . 11 6.1 General . 11 6.2 Sample length . 12
27、6.3 Screened symmetrical cables 13 6.4 Screened multi-conductor cables 13 7 Measurement . 13 7.1 General . 13 7.2 Measurement precautions . 14 7.2.1 Reduced primary current . 14 7.2.2 Uncontrolled currents 14 7.2.3 Inhomogeneities of cable screens around the circumference . 14 7.3 Calibration 14 7.4
28、 Measuring procedure 15 7.5 Evaluation of the test results . 17 8 Expression of test results 18 8.1 Expression 18 8.2 Normalised screening attenuation . 18 8.3 Temperature correction . 19 8.4 Test report 19 9 Requirement 19 Bibliography 20 Figure 1 Complete installation 7 Figure 2 Assembled injectio
29、n feature for the transmission type line, Injection method Parts list 8 Figure 3 Upper part of injection feature Position 1 . 9 Figure 4 Lower part of injection feature Position 2 . 9 Figure 5 Impedance matching part of injection feature Position 3 10 Figure 6 Insert for adapting the different sizes
30、 of the cables under test Position 4 . 10 Figure 7 Preparation of the cable under test (CUT) 12 Figure 8 Additional screening of connectors on the cable under test (CUT) . 12 Figure 9 Preparation of symmetrical samples . 13 Figure 10 Calibration set-up . 15 Figure 11 Far end measuring set-up 16 BS I
31、EC 6215346:2017 2 IEC 62153-4-6:2017 IEC 2017 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references 5 3 Terms and definitions 5 4 Physical background 5 5 Test set-up 6 5.1 General . 6 5.2 Equipment 7 5.3 Injection feature 7 5.4 Impedance of inner circuit . 10 6 Preparation of the test sample . 11 6
32、.1 General . 11 6.2 Sample length . 12 6.3 Screened symmetrical cables 13 6.4 Screened multi-conductor cables 13 7 Measurement . 13 7.1 General . 13 7.2 Measurement precautions . 14 7.2.1 Reduced primary current . 14 7.2.2 Uncontrolled currents 14 7.2.3 Inhomogeneities of cable screens around the ci
33、rcumference . 14 7.3 Calibration 14 7.4 Measuring procedure 15 7.5 Evaluation of the test results . 17 8 Expression of test results 18 8.1 Expression 18 8.2 Normalised screening attenuation . 18 8.3 Temperature correction . 19 8.4 Test report 19 9 Requirement 19 Bibliography 20 Figure 1 Complete ins
34、tallation 7 Figure 2 Assembled injection feature for the transmission type line, Injection method Parts list 8 Figure 3 Upper part of injection feature Position 1 . 9 Figure 4 Lower part of injection feature Position 2 . 9 Figure 5 Impedance matching part of injection feature Position 3 10 Figure 6
35、Insert for adapting the different sizes of the cables under test Position 4 . 10 Figure 7 Preparation of the cable under test (CUT) 12 Figure 8 Additional screening of connectors on the cable under test (CUT) . 12 Figure 9 Preparation of symmetrical samples . 13 Figure 10 Calibration set-up . 15 Fig
36、ure 11 Far end measuring set-up 16 IEC 62153-4-6:2017 IEC 2017 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ METALLIC CABLES AND OTHER PASSIVE COMPONENTS TEST METHODS Part 4-6: Electromagnetic compatibility (EMC) Surface transfer impedance Line injection method FOREWORD 1) The International Electrot
37、echnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To
38、this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC Nation
39、al Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO
40、) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation fr
41、om all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be h
42、eld responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any
43、divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to
44、IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual
45、 experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this
46、IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this
47、IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62153-4-6 has been prepared by subcommittee 46A: Coaxial cables, of IEC technical committee 46: Cables, wires, waveguides, RF connectors, R
48、F and microwave passive components and accessories cables, wires, waveguides, r.f. connectors and accessories for communication and signalling. This second edition cancels and replaces the first edition, published in 2006. BS IEC 6215346:2017 4 IEC 62153-4-6:2017 IEC 2017 The text of this Internatio
49、nal Standard is based on the following documents: FDIS Report on voting 46/650/FDIS 46/654/RVD Full information on the voting for the approval of this International Standard can be found in the report on voting indicated in the above table. This document has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62153 series, published under the general title Metallic communication cable test methods
