1、BS ISO 10935:2009ICS 37.020NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDMicroscopes Interfacing connection type CThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 30September 2009 BSI 2009ISBN 978 0 580
2、64308 8Amendments/corrigenda issued since publicationDate CommentsBS ISO 10935:2009National forewordThis British Standard is the UK implementation of ISO 10935:2009. Itsupersedes BS 7012-9:1997 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee CPW/172/5,
3、Microscopes.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer imm
4、unityfrom legal obligations.BS ISO 10935:2009Reference numberISO 10935:2009(E)ISO 2009INTERNATIONAL STANDARD ISO10935Second edition2009-08-01Microscopes Interfacing connection type C Microscopes Raccord dinterface de type C BS ISO 10935:2009ISO 10935:2009(E) PDF disclaimer This PDF file may contain
5、embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility
6、 of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation paramet
7、ers were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All right
8、s reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the
9、requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 10935:2009ISO 10935:2009(E) ISO 2009 All rights reserved iiiForeword ISO (the Internat
10、ional Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has bee
11、n established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical stand
12、ardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for
13、 voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all
14、 such patent rights. ISO 10935 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 5, Microscopes and endoscopes. This second edition cancels and replaces the first edition (ISO 10935:1996), which has been technically revised. BS ISO 10935:2009BS ISO 10935:2009INTER
15、NATIONAL STANDARD ISO 10935:2009(E) ISO 2009 All rights reserved 1Microscopes Interfacing connection type C 1 Scope This International Standard specifies the dimensions of a thread mount connection type C for a microscope imaging exit port (other than a monocular or binocular viewing tube) and the p
16、osition of the image plane. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies
17、. ISO 263:1973, ISO inch screw threads General plan and selection for screws, bolts and nuts Diameter range 0,06 to 6 in ISO 10934-1, Optics and optical instruments Vocabulary for microscopy Part 1: Light microscopy 3 Terms and definitions For the purposes of this document, the terms and definitions
18、 given in ISO 10934-1 and the following apply. 3.1 male component imaging exit port of a microscope on to which a camera or other optical detecting device is mounted 3.2 female component fitting of the camera or other optical detecting device into which the microscope exit port is inserted 4 Require
19、ments The dimensions of the male component shall be as shown in Figure 1; the dimensions of the female component shall be as shown in Figure 2. The position of the image plane shall be as shown in Figure 1 and Figure 2. BS ISO 10935:2009ISO 10935:2009(E) 2 ISO 2009 All rights reservedDimensions in m
20、illimetres Key 1 image plane aIn accordance with ISO 263. bOpen. NOTE The distance 17,53 mm is measured in air. Figure 1 Dimensions of male component and position of the image plane Dimensions in millimetres Key 1 image plane aIn accordance with ISO 263. NOTE The distance 17,53 mm is measured in air
21、. Figure 2 Dimensions of female component and position of the image plane This page has been intentionally left blankBS ISO10935:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national
22、 body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest
23、 amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be f
24、ound on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards
25、 publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation
26、 of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information serv
27、ices are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standar
28、ds. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at h
29、ttp:/CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the international standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmi
30、tted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This does not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email:
