1、BS ISO 12219-6:2017Interior air of road vehiclesPart 6: Method for the determination of the emissions of semi-volatile organic compounds from vehicle interior parts and materials at higher temperature Small chamber methodBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:
2、06BS ISO 12219-6:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 12219-6:2017.The UK participation in its preparation was entrusted to TechnicalCommittee EH/2/5, Emissions to internal environments.A list of organizations represented on this committee can b
3、eobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2017. Published by BSI Standards Limited 2017ISBN 978 0 580 81062 6ICS 13.040.20; 43.020Co
4、mpliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 March 2017.Amendments/corrigenda issued since publicationDate Text affectedBS ISO 12219-6:2017 ISO 2017Interior ai
5、r of road vehicles Part 6: Method for the determination of the emissions of semi-volatile organic compounds from vehicle interior parts and materials at higher temperature Small chamber methodAir intrieur des vhicules routiers Partie 6: Mthode pour la dtermination des missions de composs organiques
6、semi-volatils des parties et matriaux intrieurs des vhicules des tempratures leves Mthode de la petit chambreINTERNATIONAL STANDARDISO12219-6First edition2017-02Reference numberISO 12219-6:2017(E)BS ISO 12219-6:2017ISO 12219-6:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 20
7、17, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission.
8、 Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 12219-6:2017ISO 12219-6:2
9、017(E)Foreword vIntroduction vi1 Scope . 12 Normative references 13 Terms and definitions . 24 Symbols 25 Principle 26 Emission test bed preparation . 36.1 General . 36.2 Small chamber . 36.2.1 General 36.2.2 Materials . 36.2.3 Tightness 46.2.4 Air mixing . 46.2.5 Cleaning . 46.3 Small chamber tempe
10、rature control 46.4 Air humidification 46.5 Clean air supply 57 Quality control 57.1 General . 57.2 Airtightness 67.2.1 General 67.2.2 Alternative procedure 1 . 67.2.3 Alternative procedure 2 . 67.3 Recovery and sink effects. 67.4 Supply air . 77.4.1 General 77.4.2 Background concentration values 77
11、.4.3 Temperature and humidity . 88 Test specimen 88.1 General . 88.2 History of the test specimen 88.3 Packaging, transport and storage of the test specimen . 89 Standard emission test procedure . 99.1 General . 99.2 Cleaning and purification . 99.3 Test 99.3.1 General 99.3.2 Preconditioning the sam
12、ple prior to test 99.3.3 Preparation 109.3.4 Cleaning Phase 1 109.3.5 Preconditioning Phase 2 . 109.3.6 Background concentration sampling Phase 3 109.3.7 Inserting the test specimen Phase 4 .109.3.8 Conditioning at 65 C Phase 5 according to ISO 12219-4 109.3.9 Heating up and conditioning at 100 C Ph
13、ase 6 .109.3.10 Air sampling at 100 C Phase 7 . 119.3.11 End of testing . 1110 Determination of VOCs at 65 C and SVOCs at 100 C in one run .1211 Calculation of the emission rate 12 ISO 2017 All rights reserved iiiContents PageBS ISO 12219-6:2017ISO 12219-6:2017(E)12 Test report 1213 Quality assuranc
14、e/quality control (QA/QC) .14Annex A (informative) Typical test conditions and example for the experimental setup .15Bibliography .17iv ISO 2017 All rights reservedBS ISO 12219-6:2017ISO 12219-6:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of nati
15、onal standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internat
16、ional organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intende
17、d for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .i
18、so .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document w
19、ill be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and exp
20、ressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html .The committee responsible for this document is Technical Committ
21、ee ISO/TC 146, Air quality, Subcommittee SC 6, Indoor air.A list of all the parts in the ISO 12219 can be found on the ISO website. ISO 2017 All rights reserved vBS ISO 12219-6:2017ISO 12219-6:2017(E)IntroductionVolatile and semi-volatile organic compounds (VOCs and SVOCs) are widely used in industr
22、y and can be emitted by many everyday products and materials. They have attracted attention in recent years because of their impact on indoor air quality. After homes and workplaces, people spend a lot of time in their vehicles. It is important to determine the material emissions of interior parts a
23、nd to reduce them to an acceptable level, if required. Therefore, it is necessary to obtain comprehensive and reliable information about the types of organic compounds in the interior air of vehicles and also their concentrations.Monitoring emissions from vehicle trim components can be performed in
24、several ways and the approach selected depends upon the desired outcome and the material type. For example, to obtain emissions data from complete assemblies (e.g. a dashboard or seat), it is necessary to employ emission chambers or bags that have sufficient volume to house the complete assembly (ty
25、pically 1 m3). The performance of such tests may take several hours or even days, depending on specified equilibration times and the requirements of the relevant test protocol.This document outlines a screening method for measuring the types and levels of VOCs and SVOCs in vehicle trim components un
26、der controlled conditions using a small emission test chamber (small chamber). The described screening method can be used to investigate the emissions of car interior trim under conditions of real use where elevated temperatures are prevailing in the cabin of road vehicles. For this purpose, tests a
27、re performed at 65 C and 100 C. ISO 12219-6 describes requirements for a small chamber and a test protocol. Measurements are carried out according to ISO 16000-6 (VOCs).The capacity of a small chamber is not limited to small assemblies or representative test specimens of homogeneous car trim materia
28、ls. Small chambers allow qualitative and quantitative VOC and SVOC emission data to be measured and recorded. The subsequent emission data can be used to develop a correlation between material level methods and the vehicle level method.This document is based on VDA 2762and correlates to ISO 16000-9.
29、Besides the ISO 12219-series, there are parts of ISO 16000 which deal with the measurements of vapour-phase organic chemicals and vapour-phase chemical emissions: Part 3: Determination of formaldehyde and other carbonyl compounds in indoor air and test chamber air Active sampling method Part 5: Samp
30、ling strategy for volatile organic compounds (VOCs) Part 6: Determination of volatile organic compounds in indoor and test chamber air by active sampling on Tenax TAsorbent, thermal desorption and gas-chromatography using MS or MS-FID Part 9: Determination of the emission of volatile organic compoun
31、ds from building products and furnishing Emission test chamber method Part 10: Determination of the emission of volatile organic compounds from building products and furnishing Emission test cell method Part 11: Determination of the emission of volatile organic compounds from building products and f
32、urnishing Sampling, storage of samples and preparation of test specimens Part 24: Performance test for evaluating the reduction of volatile organic compound (except formaldehyde) concentrations by sorptive building materials Part 25: Determination of the emission of semi-volatile organic compounds f
33、or building products Micro chamber methodvi ISO 2017 All rights reservedBS ISO 12219-6:2017Interior air of road vehicles Part 6: Method for the determination of the emissions of semi-volatile organic compounds from vehicle interior parts and materials at higher temperature Small chamber methodWARNIN
34、G This method is unsuitable for materials that are not stable at 100 C in air. Application of this document for thermally unstable materials could lead to irreversible contamination of the test equipment.1 ScopeThis document describes a qualitative and quantitative analytical method for vapour-phase
35、 organic compounds released from car trim materials under simulated real use conditions, i.e. a vehicle is parked for several hours in direct sunlight. Under these conditions, some interior parts and materials reach higher temperatures than 65 C (ISO 12219-4), e.g. a dashboard can reach temperatures
36、 up to 120 C. This document can be implemented as an optional addition to ISO 12219-4 so that VOC, volatile carbonyl and SVOC testing can all be completed within one day. This part has been added to gain insight into the emission behaviour and emission potential of selected vehicle interior parts an
37、d materials exposed to higher temperatures. (By convention, 100 C is set as the higher temperature.) The test is performed in small emission test chambers (small chambers). These small chambers are intended to provide a transfer function for vehicle level emissions. This method is intended for evalu
38、ating new car interior trim components but can, in principle, be applied to used car components.The specified analytical procedure for SVOCs and semi-volatile carbonyls is ISO 16000-6.This document is complementary to existing standards1,2and provides third party test laboratories and manufacturing
39、industry with an approach for identifying the effect of real use conditions on specific VOC and SVOC emissions data, comparing emissions from various assemblies with regards to specific VOC and SVOC emissions, evaluating and sorting specific assemblies regarding specific VOC and SVOC emissions data,
40、 providing specific VOC and SVOC emissions data to develop and verify a correlation between component level methods and in vehicle air quality and evaluating prototype, “low-emission” assemblies during development.The method described can be exclusively performed as a high temperature test or it can
41、 be performed in combination with the determination of VOCs at 65 C in one run, which is described in ISO 12219-4.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references,
42、 only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 12219-4, Interior air of road vehicles Part 4: Method for the determination of the emissions of volatile organic compounds from vehicle interior parts and mat
43、erials Small chamber methodINTERNATIONAL STANDARD ISO 12219-6:2017(E) ISO 2017 All rights reserved 1BS ISO 12219-6:2017ISO 12219-6:2017(E)ISO 16000-6:2011, Indoor air Part 6: Determination of volatile organic compounds in indoor and test chamber air by active sampling on Tenax TAsorbent, thermal des
44、orption and gas chromatography using MS or MS-FID3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 12219-4 and the following apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: ISO Online browsing p
45、latform: available at h t t p :/ www .iso .org/ obp IEC Electropedia: available at h t t p :/ www .electropedia .org/ 3.1semi-volatile organic compoundSVOCorganic compound whose boiling point is in the range from (240 C to 260 C) to (380 C to 400 C)Note 1 to entry: This classification has been defin
46、ed by the World Health Organization3.Note 2 to entry: Boiling points of some compounds are difficult or impossible to determine because they decompose before they boil at atmospheric pressure. Vapour pressure is another criterion for classification of compound volatility that can be used for classif
47、ication of organic chemicals. SVOCs have vapour pressures between 102mPa and 10 Pa.SOURCE: ISO 16000-25:2011, 3.163.2target semi-volatile organic compoundproduct-specific semi-volatile organic compound4 SymbolsSymbol Meaning Unitt time hq area specific air flow rate q =n/LAm3m2h1qAemission rate per
48、unit area gm-2h1qmemission rate per unit mass gkg1h1n air change rate h1nLspecific leak rate h1LAsurface loading of chamber m2m-3V air flow rate entering the small chamber m3h15 PrincipleA vehicle interior trim component or material sample, referred to as a test specimen, is inserted into a small ch
49、amber (0,5 m3to 4,0 m3) and kept under controlled conditions of temperature, humidity and air change rate (air flow rate). The air inside the chamber is thoroughly mixed at all times so that the concentration of any organic substances emitted by the test specimen is uniform both within the chamber and in the flow of air exhausting from the chamber.The air exhausting from the chamber is sampled for semi-volatile organic comp
