1、BSI Standards PublicationBS ISO 16462:2014Cubic boron nitride inserts,tipped or solid Dimensions,typesBS ISO 16462:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 16462:2014. It supersedes BS ISO 16462:2004 which is withdrawn.The UK participation in its pr
2、eparation was entrusted to Technical Committee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are
3、responsible for its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 83606 0ICS 25.100.01Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the St
4、andards Policy and Strategy Committee on 31 May 2014.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e dBS ISO 16462:2014 ISO 2014Cubic boron nitride inserts, tipped or solid Dimensions, typesPlaquettes en nitrure de bore cubique, brases ou monobloc Dimensions, typesINTERNATIO
5、NAL STANDARDISO16462Second edition2014-06-01Reference numberISO 16462:2014(E)BS ISO 16462:2014ISO 16462:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in a
6、ny form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postal
7、e 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 16462:2014ISO 16462:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Insert shapes and design . 13.1 Insert shapes
8、 . 13.2 Normal clearance n13.3 Cutting edge corner 13.4 Tolerance class 13.5 Design of cutting edges 23.6 Insert type . 24 Designation 24.1 General . 24.2 Designation of inserts for turning 24.3 Designation of a tipped insert for milling 25 Dimensions . 35.1 Insert shape T with fixing hole (inserts
9、for turning) . 35.2 Insert shape S with fixing hole (inserts for turning) 45.3 Insert shape C with fixing hole (inserts for turning) . 55.4 Insert shape D with fixing hole (inserts for turning) . 65.5 Insert shape V with fixing hole (inserts for turning) . 75.6 Insert shape S with fixing hole (inser
10、ts for milling) . 85.7 Insert shape C with fixing hole (inserts for milling) . 95.8 Insert shapes C, R, S, and T without fixing hole (inserts for turning) 95.9 Insert shapes S and T without fixing hole (inserts for milling) .115.10 Insert shapes S and T without fixing hole (inserts for milling) .125
11、.11 Insert shape W with fixing hole (inserts for turning) 135.12 Insert shape W without fixing hole (inserts for turning) 146 Cutting edge length, l1, of tipped inserts .156.1 General 156.2 Inserts with radius 156.3 Inserts with wiper edge .157 Base material, cutting material 168 Measurements 169 Ma
12、rking .16Annex A (informative) Relationship between designations in ISO 16462 and ISO/TS 13399-2 .17BS ISO 16462:2014ISO 16462:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing Int
13、ernational Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison w
14、ith ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directive
15、s, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some o
16、f the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declaratio
17、ns received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about
18、ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small Tools, Subcommittee SC 9, Tools with cutting edges made of hard cutting materials.This second editi
19、on cancels and replaces the first edition (ISO 16462:2004), of which it constitutes a minor revision.iv ISO 2014 All rights reservedBS ISO 16462:2014INTERNATIONAL STANDARD ISO 16462:2014(E)Cubic boron nitride inserts, tipped or solid Dimensions, types1 ScopeThis International Standard applies to ins
20、erts with insert shapes in accordance with ISO 883, ISO 3364, ISO 3365, and ISO 6987, tipped with cubic boron nitride (BL, BH, BC) or made of solid cubic boron nitride (BL, BH, BC).2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are
21、 indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 513, Classification and application of hard cutting materials for metal removal with defined cutting
22、edges Designation of the main groups and groups of applicationISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole DimensionsISO 1832, Indexable inserts for cutting tools DesignationISO 3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindr
23、ical fixing hole DimensionsISO 3365, Indexable hardmetal (carbide) inserts with wiper edges, without fixing hole DimensionsISO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole Dimensions3 Insert shapes and design3.1 Insert shapesTriangular (T), square (
24、S), rhombic 80 (C), 55 (D) and 35 (V), round (R), and trigon (W).3.2 Normal clearance nNormal clearance 0 (N), 5 (B), 7 (C), and 11 (P).3.3 Cutting edge cornerInserts for turning with corner radius r0,2 mm, 0,4 mm, 0,8 mm, 1,2 mm, and 1,6 mm.Inserts for milling with wiper edge.NOTE The design of non
25、-tipped corners is optional.3.4 Tolerance classTolerance class in accordance with ISO 1832 shall be applied. In Tables 1 to 12, this position is shown with a dot (). ISO 2014 All rights reserved 1BS ISO 16462:2014ISO 16462:2014(E)3.5 Design of cutting edgesAny design shall be indicated in the design
26、ation (see ISO 1832).3.6 Insert typeThe styles of tipped or solid cutting edges in accordance with ISO 1832 shall be applied.4 Designation4.1 GeneralThe designation of inserts tipped or solid with cubic boron nitride (BL, BH, BC) is based on ISO 1832. The letter symbol for the cutting edge condition
27、 and the letter symbol for the insert type shall be indicated in the designation in each case.Designations contained in 4.2 and 4.3 are examples of the use of designations in accordance with ISO 1832.4.2 Designation of inserts for turning4.2.1 Solid insert (S)Designation of a rhombic insert with inc
28、luded angle r= 80 (C), normal clearance n= 0 (N), with tolerance class M, without chip breakers and without fixing hole (N), with side length l = 9,67 mm (09), thickness s = 3,18 mm (03), corner radius r= 0,8 mm (08), with chamfered and rounded cutting edges (S), insert type solid (S), cutting mater
29、ial in accordance with ISO 513 (e.g. BL05):Insert CNMN 090308S S BL05 NOTE BL05 is optional in accordance with ISO 1832, designation symbol 13.4.2.2 Insert, tipped full thickness one corner (T)Designation of a rhombic insert with included angle r= 55 (D), normal clearance n= 0 (N), with tolerance cl
30、ass M, without chip breakers and with cylindrical fixing hole (A), with side length l = 15,5 mm (15), thickness s = 4,76 mm (04), corner radius r= 0,8 mm (08), with chamfered and rounded cutting edges (S), tipped full thickness one corner (T), long (L), cutting material in accordance with ISO 513 (e
31、.g. BL05):Insert DNMA 150408S TL BL05 NOTE BL05 is optional in accordance with ISO 1832, designation symbol 13.4.3 Designation of a tipped insert for millingDesignation of a square insert (S) with normal clearance n= 7 (C), with tolerance class G, without chip breakers and with fixing hole (W), with
32、 side length l = 12,7 mm (12), thickness s = 4,76 mm (04), cutting edge angle r= 75 (E), normal clearance at wiper edge = 15 (D), right-hand type (R), tipped one side one corner (A), long (L), cutting material in accordance with ISO 513 (e.g. BL05):Insert SCGW 1204EDR AL BL05 NOTE BL05 is optional i
33、n accordance with ISO 1832, designation symbol 13.2 ISO 2014 All rights reservedBS ISO 16462:2014ISO 16462:2014(E)5 Dimensions5.1 Insert shape T with fixing hole (inserts for turning)See Figure 1 and Table 1.NOTE For the dimensions of l1, see Table 13.Figure 1Table 1Designation d d1l m s nrTCW 09 02
34、 02S 5,56 2,5 9,63 8,137 2,38 7 0,2TCW 09 02 04S 5,56 2,5 9,63 7,943 2,38 7 0,4TCW 09 02 08S 5,56 2,5 9,63 7,541 2,38 7 0,8TCW 11 02 02S 6,35 2,8 11 9,322 2,38 7 0,2TCW 11 02 04S 6,35 2,8 11 9,128 2,38 7 0,4TCW 11 02 08S 6,35 2,8 11 8,731 2,38 7 0,8TCW 16 T3 02S 9,525 4,4 16,5 14,084 3,97 7 0,2TCW 1
35、6 T3 04S 9,525 4,4 16,5 13,891 3,97 7 0,4TCW 16 T3 08S 9,525 4,4 16,5 13,494 3,97 7 0,8TCW 16 T3 12S 9,525 4,4 16,5 13,097 3,97 7 1,2TCW 16 T3 16S 9,525 4,4 16,5 12,700 3,97 7 1,6TNA 11 03 02S 6,35 2,26 11 9,322 3,18 0 0,2TNA 11 03 04S 6,35 2,26 11 9,128 3,18 0 0,4TNA 11 03 08S 6,35 2,26 11 8,731 3,
36、18 0 0,8TNA 16 04 04S 9,525 3,81 16,5 13,891 4,76 0 0,4TNA 16 04 08S 9,525 3,81 16,5 13,494 4,76 0 0,8TNA 16 04 12S 9,525 3,81 16,5 13,097 4,76 0 1,2TNA 16 04 16S 9,525 3,81 16,5 12,700 4,76 0 1,6TPW 08 02 02S 4,763 2,3 8,2 6,945 2,38 11 0,2TPW 08 02 04S 4,763 2,3 8,2 6,747 2,38 11 0,4TPW 08 02 08S
37、4,763 2,3 8,2 6,350 2,38 11 0,8TPW 09 02 02S 5,56 2,5 9,63 8,137 2,38 11 0,2 ISO 2014 All rights reserved 3BS ISO 16462:2014ISO 16462:2014(E)Table 1 (continued)Designation d d1l m s nrTPW 09 02 04S 5,56 2,5 9,63 7,943 2,38 11 0,4TPW 09 02 08S 5,56 2,5 9,63 7,541 2,38 11 0,8TPW 11 02 02S 6,35 2,8 11
38、8,731 2,38 11 0,2TPW 11 02 04S 6,35 2,8 11 8,137 2,38 11 0,4TPW 11 02 08S 6,35 2,8 11 7,943 2,38 11 0,8TPW 11 03 02S 6,35 3,3 11,0 9,327 3,18 11 0,2TPW 11 03 04S 6,35 3,3 11,0 9,128 3,18 11 0,4TPW 11 03 08S 6,35 3,3 11,0 8,731 3,18 11 0,8TPW 16 03 04S 9,525 4,4 16,5 13,891 3,18 11 0,4TPW 16 03 08S 9
39、,525 4,4 16,5 13,494 3,18 11 0,8TPW 16 T3 04S 9,525 4,4 16,5 13,891 3,97 11 0,4TPW 16 T3 08S 9,525 4,4 16,5 13,494 3,97 11 0,8TPW 16 T3 12S 9,525 4,4 16,5 13,097 3,97 11 1,2TPW 16 T3 16S 9,525 4,4 16,5 12,700 3,97 11 1,6TPW 16 04 04S 9,525 4,4 16,5 13,891 4,76 11 0,4TPW 16 04 08S 9,525 4,4 16,5 13,4
40、94 4,76 11 0,85.2 Insert shape S with fixing hole (inserts for turning)See Figure 2 and Table 2.NOTE For the dimensions of l1, see Table 13.Figure 2Table 2Designation d d1l m s nrSCW 09 T3 02S 9,525 4,4 9,525 1,889 3,97 7 0,2SCW 09 T3 04S 9,525 4,4 9,525 1,808 3,97 7 0,4SCW 09 T3 08S 9,525 4,4 9,525
41、 1,644 3,97 7 0,8SCW 09 T3 12S 9,525 4,4 9,525 1,479 3,97 7 1,2SCW 12 04 04S 12,7 5,5 12,7 2,466 4,76 7 0,44 ISO 2014 All rights reservedBS ISO 16462:2014ISO 16462:2014(E)Table 2 (continued)Designation d d1l m s nrSCW 12 04 08S 12,7 5,5 12,7 2,301 4,76 7 0,8SCW 12 04 12S 12,7 5,5 12,7 2,137 4,76 7 1
42、,2SNA 09 03 04S 9,525 3,81 9,525 1,808 3,18 0 0,4SNA 09 03 08S 9,525 3,81 9,525 1,644 3,18 0 0,8SNA 09 03 12S 9,525 3,81 9,525 1,479 3,18 0 1,2SNA 12 04 04S 12,7 5,16 12,7 2,466 4,76 0 0,4SNA 12 04 08S 12,7 5,16 12,7 2,301 4,76 0 0,8SNA 12 04 12S 12,7 5,16 12,7 2,137 4,76 0 1,2SNA 12 04 16S 12,7 5,1
43、6 12,7 1,972 4,76 0 1,65.3 Insert shape C with fixing hole (inserts for turning)See Figure 3 and Table 3.NOTE For the dimensions of l1, see Table 13.Figure 3Table 3Designation d d1l m1m2s nrCCW 06 02 02S 6,35 2,8 6,45 1,652 0,908 2,38 7 0,2CCW 06 02 04S 6,35 2,8 6,45 1,544 0,848 2,38 7 0,4CCW 06 02
44、08S 6,35 2,8 6,45 1,323 0,727 2,38 7 0,8CCW 09 T3 02S 9,525 4,4 9,67 2,535 1,392 3,97 7 0,2CCW 09 T3 04S 9,525 4,4 9,67 2,426 1,333 3,97 7 0,4CCW 09 T3 08S 9,525 4,4 9,67 2,206 1,212 3,97 7 0,8CCW 09 T3 12S 9,525 4,4 9,67 1,985 1,091 3,97 7 1,2CCW 12 04 04S 12,7 5,5 12,9 3,308 1,818 4,76 7 0,4CCW 12
45、 04 08S 12,7 5,5 12,9 3,088 1,697 4,76 7 0,8CCW 12 04 12S 12,7 5,5 12,9 2,867 1,576 4,76 7 1,2CCW 12 04 16S 12,7 5,5 12,9 2,646 1,454 4,76 7 1,6 ISO 2014 All rights reserved 5BS ISO 16462:2014ISO 16462:2014(E)Table 3 (continued)Designation d d1l m1m2s nrCNA 09 03 04S 9,525 3,81 9,67 2,426 1,333 3,18
46、 0 0,4CNA 09 03 08S 9,525 3,81 9,67 2,206 1,212 3,18 0 0,8CNA 12 04 04S 12,7 5,16 12,9 3,308 1,818 4,76 0 0,4CNA 12 04 08S 12,7 5,16 12,9 3,088 1,697 4,76 0 0,8CNA 12 04 12S 12,7 5,16 12,9 2,867 1,576 4,76 0 1,2CNA 12 04 16S 12,7 5,16 12,9 2,646 1,454 4,76 0 1,6CPW 06 02 02S 6,35 2,8 6,45 1,652 0,90
47、8 2,38 11 0,2CPW 06 02 04S 6,35 2,8 6,45 1,544 0,848 2,38 11 0,4CPW 06 02 08S 6,35 2,8 6,45 1,323 0,727 2,38 11 0,8CPW 09 03 02S 9,525 4,4 9,67 2,534 1,392 3,18 11 0,2CPW 09 03 04S 9,525 4,4 9,67 2,426 1,333 3,18 11 0,4CPW 09 03 08S 9,525 4,4 9,67 2,206 1,212 3,18 11 0,8CPW 09 T3 02S 9,525 4,4 9,67
48、2,534 1,392 3,97 11 0,2CPW 09 T3 04S 9,525 4,4 9,67 2,426 1,333 3,97 11 0,4CPW 09 T3 08S 9,525 4,4 9,67 2,206 1,212 3,97 11 0,8CPW 09 T3 12S 9,525 4,4 9,67 1,985 1,091 3,97 11 1,25.4 Insert shape D with fixing hole (inserts for turning)See Figure 4 and Table 4.NOTE For the dimensions of l1, see Table 13.Figure 46 ISO 2014 All rights reservedBS ISO 16462:2014ISO 16462:2014(E)Table 4Designation d d1l m s nrDCW 07 02 02S 6,35 2,8 7,75 3,464 2,38 7 0,2DCW 07 02 04S 6,35 2,8 7,75 3,238 2,38 7 0,4DCW 07 02 08S 6,35 2,8 7,75 2,776 2,38 7 0,8DCW 11 T3 02S 9,525 4,4 11,6 5,315 3,97 7 0,2DC
