1、BS ISO 16847:2016Textiles Test methodfor assessing the mattingappearance of napped fabricsafter cleansingBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS ISO 16847:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 16847:201
2、6. The UK participation in its preparation was entrusted to TechnicalCommittee TCI/82, Textiles care labelling, dry cleaning, domesticlaundering and drying.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include al
3、l the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016. Published by BSI Standards Limited 2016ISBN 978 0 580 88922 6ICS 59.080.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British St
4、andard was published under the authority of theStandards Policy and Strategy Committee on 31 December 2016.Amendments/Corrigenda issued since publicationDate Text affectedBS ISO 16847:2016 ISO 2016Textiles Test method for assessing the matting appearance of napped fabrics after cleansingTextiles Mth
5、ode dessai pour lvaluation de laspect du moutonnement des toffes grattes aprs nettoyageINTERNATIONAL STANDARDISO16847First edition2016-12-15Reference numberISO 16847:2016(E)BS ISO 16847:2016ISO 16847:2016(E)ii ISO 2016 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in Switzerlan
6、dAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requeste
7、d from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 16847:2016ISO 16847:2016(E)Foreword ivIntroduction v
8、1 Scope . 12 Normative references 13 Terms and definitions . 14 Principle 25 Apparatus . 26 Test specimens 37 Procedure. 38 Expression of results 49 Test report . 4 ISO 2016 All rights reserved iiiContents PageBS ISO 16847:2016ISO 16847:2016(E)ForewordISO (the International Organization for Standard
9、ization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to
10、be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used
11、to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of
12、the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified d
13、uring the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the m
14、eaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.This document was prepared by Tech
15、nical Committee ISO/TC 38, Textiles, Subcommittee SC 2, Cleansing, finishing and water resistance tests.iv ISO 2016 All rights reservedBS ISO 16847:2016ISO 16847:2016(E)IntroductionWith use, the surface of napped fabrics changes significantly. This change in appearance, known as matting, is more or
16、less severe and is related to the fibre, fabric or finishing characteristics.Based on the structure of other ISO standards dealing with the change in appearance after cleansing, this document has been elaborated to solve this situation. ISO 2016 All rights reserved vBS ISO 16847:2016BS ISO 16847:201
17、6Textiles Test method for assessing the matting appearance of napped fabrics after cleansing1 ScopeThis document specifies a method for assessing the matting appearance of the napped fabrics (fleece fabrics) tested, after one or several cleansing treatments.This method has been developed for use pri
18、marily with Type B domestic washing machines, as defined in ISO 6330, in the cleansing process. However, it is possible to use it with Type A machines, as defined in ISO 6330. This test method can be used for judging matting appearance after other cleansing processes.2 Normative referencesThe follow
19、ing documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 105-
20、A03, Textiles Tests for colour fastness Part A03: Grey scale for assessing stainingISO 139, Textiles Standard atmospheres for conditioning and testingISO 3175 (all parts), Textiles Professional care, drycleaning and wetcleaning of fabrics and garmentsISO 6330, Textiles Domestic washing and drying pr
21、ocedures for textile testingISO 15797, Textiles Industrial washing and finishing procedures for testing of workwear3 Terms and definitionsFor the purposes of this document, the following terms and definitions apply.ISO and IEC maintain terminological databases for use in standardization at the follo
22、wing addresses: ISO Online browsing platform: available at https:/www.iso.org/obp/ui/ IEC Electropedia: available at http:/www.electropedia.org/3.1mattingdisorientation of the raised fibres of a napped fabric, which produces a visible surface changeNote 1 to entry: See Figure 1.INTERNATIONAL STANDAR
23、D ISO 16847:2016(E) ISO 2016 All rights reserved 1BS ISO 16847:2016ISO 16847:2016(E)Figure 1 Example of matting appearance of napped fabric4 PrincipleFabric specimens are subjected to procedures simulating cleansing practices. One of the domestic washing and drying procedures specified in ISO 6330,
24、one of the professional procedures specified in the series of ISO 3175 or one of the industrial procedures as specified in ISO 15797 is used, as agreed between the interested parties. If the interested parties decide that other cleansing processes are to be used, this fact shall be reported.5 Appara
25、tus5.1 Washing and drying apparatus, as specified in ISO 6330, professional care apparatus, as specified in ISO 3175 or industrial laundering apparatus as specified in ISO 15797.5.2 Lighting.The evaluation area shall be a darkened room, using the overhead lighting arrangement shown in Figure 2 and c
26、omprising the following items. Lamp dimensions should be chosen to extend beyond the overall surface of a test specimen and replicas, when used for the assessment.5.2.1 Two CW (cool white) fluorescent lamps, placed side by side, without baffle or glass, a minimum of 2 m in length each.5.2.2 One whit
27、e enamel reflector, without baffle or glass.5.2.3 One specimen holder.5.2.4 One thick plywood viewing board, painted grey to match the grade 2 on the grey scale for assessing staining specified in ISO 105-A03.2 ISO 2016 All rights reservedBS ISO 16847:2016ISO 16847:2016(E)Dimensions in metresKey1 re
28、plica2 test specimen3 board for viewing4 example of fluorescent lamp placementFigure 2 Lighting equipment for viewing test specimens6 Test specimensPrepare three test specimens, each measuring 38 cm x 38 cm, cut parallel to the length direction, pinked to prevent fraying and marked to indicate the l
29、ength direction.If the matting appearance shall be assessed on both faces, mark the front face.7 Procedure7.1 Treat each specimen according to one of the cleansing procedures specified in ISO 6330, ISO 3175 or ISO 15797, as agreed between the interested parties.7.2 If required, repeat the selected t
30、reatment four times, to give a total of five cycles (one cycle consists of one washing and one drying).7.3 Condition the test specimens in the standard atmosphere according to ISO 139 for a minimum of 4 h by hanging each specimen unfolded with the length direction vertical to avoid distortion.7.4 Fo
31、r the evaluation, carry out steps 7.5 to 7.11.7.5 Three observers shall rate each treated test specimen independently. ISO 2016 All rights reserved 3BS ISO 16847:2016ISO 16847:2016(E)7.6 Mount the test specimen on the viewing board (5.2.4) as illustrated in Figure 2, with the length direction vertic
32、al. If the matting appearance shall be assessed on both faces, proceed to 7.6 to 7.11 with the marked front faces, and then repeat 7.6 to 7.11 with the other faces.7.7 The overhead fluorescent light (5.2.1) shall be the only light source for the viewing board, and all other lights in the room shall
33、be turned off. It has been the experience of many observers that the light reflected from the side walls near the viewing board can interfere with the rating results. It is recommended that the side walls be painted black or that blackout curtains be mounted on either side of the viewing board to el
34、iminate the reflective interference.7.8 The observer shall stand directly in front of the specimen, 1,2 m away from the board. It has been found that normal variations in the height of the observer above and below the arbitrary 1,5 m eye level have no significant effect on the rating given.7.9 Assig
35、n the number of the grade which most nearly matches the appearance of the test specimen, or assign ratings midway between those whole-number standards which have no half-number standards separating them if the appearance of the specimens warrants it (see Table 1).7.10 A 5 rating represents the best
36、retention of original appearance, while a 1 rating represents the poorest retention of original appearance.7.11 Similarly, the observer shall independently rate each of the other two test specimens. The other two observers shall proceed in the same manner, assigning ratings independently.Table 1 Mat
37、ting grading schemeGrade Description5 No change4 Slight surface matting3 Moderate surface matting2 Distinct surface matting1 Dense surface matting8 Expression of resultsCalculate the median of the nine observations made by the three observers on the set of three test specimens for the concerned face
38、. Report the median to the nearest half rating.9 Test reportThe test report shall include the following information:a) a reference to this International Standard (ISO 16847:2016);b) details of the sample evaluated;c) details of the cleansing procedures used;d) the number of cleansing cycles used;e)
39、for each concerned face, the fabric matting rating as calculated according to Clause 8 associated to the description as stated in Table 1;f) details of any deviation from the specified procedure.4 ISO 2016 All rights reservedBS ISO 16847:2016BS ISO 16847:2016ISO 16847:2016(E) ISO 2016 All rights res
40、ervedICS 59.080.30Price based on 4 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products
41、are published by BSI Standards Limited.British Standards Institution (BSI)About usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been caref
42、ully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out
43、 more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard cop
44、ies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.Copyright in BSI publicationsAll the content in BSI publications, including British Standards, is the property of and
45、copyrighted by BSI or some person or entity that owns copyright in the information used (such as the international standardization bodies) and has formally licensed such information to BSI for commercial publication and use.Save for the provisions below, you may not transfer, share or disseminate an
46、y portion of the standard to any other person. You may not adapt, distribute, commercially exploit, or publicly display the standard or any portion thereof in any manner whatsoever without BSIs prior written consent.Storing and using standardsStandards purchased in soft copy format: A British Standa
47、rd purchased in soft copy format is licensed to a sole named user for personal or internal company use only. The standard may be stored on more than 1 device provided that it is accessible by the sole named user only and that only 1 copy is accessed at any one time. A single paper copy may be printe
48、d for personal or internal company use only.Standards purchased in hard copy format: A British Standard purchased in hard copy format is for personal or internal company use only. It may not be further reproduced in any format to create an additional copy. This includes scanning of the document.If y
49、ou need more than 1 copy of the document, or if you wish to share the document on an internal network, you can save money by choosing a subscription product (see Subscriptions).Reproducing extractsFor permission to reproduce content from BSI publications contact the BSI Copyright & Licensing team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to bsigroup.co
