1、BSI Standards PublicationBS ISO 17447-3:2015Road Vehicles Glow-plugswith conical seating and theircylinder head housingPart 3: Tests and requirementsBS ISO 17447-3:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 17447-3:2015.Together with BS ISO 17747-1:20
2、15 and BS ISO 17747-2:2015,it supersedes BS AU 262-1:1995, BS AU 262-2:1995 and BS ISO7578:2008 which are withdrawn. Together with BS ISO 6550-3:2013,BS ISO 17747-1:2015 and BS ISO 17747-2:2015, it supersedes BS ISO6550-3:2009 which is withdrawn. Together with BS ISO 6550-4:2014,BS ISO 17747-1:2015
3、and BS ISO 17747-2:2015, it supersedes BS ISO6550-4:2009 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MCE/22, Engines for road vehicles.A list of organizations represented on this committee can beobtained on request to its secretary.This publication
4、does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2015. Published by BSI StandardsLimited 2015ISBN 978 0 580 81749 6ICS 43.060.50Compliance with a British Standard cannot confer immunity fromlega
5、l obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 August 2015.Amendments issued since publicationDate Text affectedBS ISO 17447-3:2015 ISO 2015Road Vehicles Glow-plugs with conical seating and their cylinder head housing Part 3:
6、 Tests and requirementsVhicules routiers Bougies de prchauffage fourreau et conique et leur logement dans la culasse Partie 3: Essais et exigencesINTERNATIONAL STANDARDISO17447-3First edition2015-05-15Reference numberISO 17447-3:2015(E)BS ISO 17447-3:2015ISO 17447-3:2015(E)ii ISO 2015 All rights res
7、ervedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an int
8、ranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww
9、.iso.orgBS ISO 17447-3:2015ISO 17447-3:2015(E)Foreword ivIntroduction v1 Scope . 12 Normative references 13 Terms and definitions . 14 Tests and general requirements 14.1 General . 14.2 Gas tightness . 14.2.1 Test . 14.2.2 Requirement 24.3 Thermal characteristic . 24.3.1 Test sample preparation 24.3
10、.2 Test . 24.3.3 Requirement 24.4 Electrical resistance at room temperature . 34.4.1 Test . 34.4.2 Requirement 34.5 Current characteristic . 34.5.1 Test . 34.5.2 Requirement 34.6 Higher voltage 34.6.1 Test . 34.6.2 Requirement 34.7 Vibration (sinusoidal) . 34.7.1 Test . 34.7.2 Requirement 44.8 Endur
11、ance . 44.8.1 Test . 44.8.2 Requirement 44.9 Marking and labelling . 4 ISO 2015 All rights reserved iiiContents PageBS ISO 17447-3:2015ISO 17447-3:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The w
12、ork of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-govern
13、mental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in t
14、he ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the poss
15、ibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list o
16、f patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as
17、information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT), see the following URL: Foreword Supplementary information .The committee responsible for this document is ISO/TC 22, Road vehicles, Subcommittee SC 32, Electrical and electronic components and general sy
18、stem aspects.ISO 17447 consists of the following parts, under the general title Road Vehicles Glow-plugs with conical seating and their cylinder head housing: Part 1: Basic characteristics and dimensions for metal-sheath-type glow-plugs Part 2: Basic characteristics and dimensions for ceramic-sheath
19、-type glow-plugs Part 3: Tests and requirementsiv ISO 2015 All rights reservedBS ISO 17447-3:2015ISO 17447-3:2015(E)IntroductionThe purpose of this International Standard is to provide a compact and concise specification on glow-plugs and their cylinder head housings, which is to replace the existin
20、g single standards on each type of glow-plugs.It is intended to specify the main properties, the design requirements, and the dimensions of most of the existing types of glow-plugs and their cylinder head housings. It is to enable the user to work with one comprehensive document valid for most types
21、 of glow-plugs instead of a number of standards, each of them specified for one type only.ISO 17447-1 covers basic characteristics and dimensions for metal-sheath-type glow-plugs. ISO 17447-2 covers basic characteristics and dimensions for ceramic-sheath-type glow-plugs. Tests and requirements are d
22、efined in this part of ISO 17447.It is intended to withdraw the following standards on glow-plugs and their cylinder head housing as soon as this part of ISO 17447 is published:ISO 6550-1, ISO 6550-2, ISO 6550-3, ISO 6550-4, ISO 7578. ISO 2015 All rights reserved vBS ISO 17447-3:2015BS ISO 17447-3:2
23、015Road Vehicles Glow-plugs with conical seating and their cylinder head housing Part 3: Tests and requirements1 ScopeThis part of ISO 17447 specifies general requirements and test methods for sheath-type glow-plugs. Detailed test condition(s) and/or requirement(s) are agreed between the glow-plug m
24、anufacturers and the engine manufacturer. It is applicable to glow-plugs conforming to ISO 17447-1 and ISO 17447-2, used in diesel (compression ignition) engines.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for
25、its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.IEC 60068-2-6, Environmental testing Part 2-6: Tests Test Fc: Vibration (sinusoidal)3 Terms and definitionsFor the purpose o
26、f this document, the following terms and definitions apply.3.1nominal voltagevoltage as marked on the housing of the glow-plugNote 1 to entry: The nominal voltage of the glow-plug is generally not identical to the supply voltage of the vehicles electrical system.3.2test voltagevoltage(s) applied to
27、the glow-plug under test4 Tests and general requirements4.1 GeneralDetailed test condition(s) and/or requirement(s) are agreed between the glow-plug manufacturers and the engine manufacturer.If not otherwise specified, all tests shall be carried out at room temperature (RT) (23 5) C.4.2 Gas tightnes
28、s4.2.1 TestMount the sample on a test assembly with the tightening torque as specified in ISO 17447-1 and ISO 17447-2.INTERNATIONAL STANDARD ISO 17447-3:2015(E) ISO 2015 All rights reserved 1BS ISO 17447-3:2015ISO 17447-3:2015(E)Subject the sample to a pressure of 4 MPa (40 bar)1)above ambient air p
29、ressure on the sheath end for a duration of 15 s. Use air, nitrogen, carbon dioxide, or any other detection gas.4.2.2 RequirementThe measured total leakage shall not exceed 2 cm3/min. If neither air nor nitrogen is used, the leakage rate shall be converted to that of air using the specific volume of
30、 the detection gas.4.3 Thermal characteristic4.3.1 Test sample preparationBefore the test, pre-heat the sample to oxidation at the nominal voltage of the glow-plug and then allow it to cool to RT. The time for oxidation shall be as agreed between the glow-plug manufacturer and the engine manufacture
31、r, e.g. three times the duration of the glow cycle.4.3.2 TestCarry out the test using a test installation in accordance with Figure 1, equipped with a cooling device by which the temperature can be maintained below 30 C, measured at the seating of the glow-plug housing.If the thermal behaviour is me
32、asured in accordance with a specific application, this shall be by agreement between the glow-plug manufacturer and the engine manufacturer.Carry out the test at the test voltage(s) of the glow-plug as specified in the description of the glow plug system.Temperature measurements shall be made withou
33、t direct contact.KeyZ measuring zoneFigure 1 Test installation4.3.3 RequirementThe hottest point of standard warm-up sheath-type glow-plugs shall be within the measuring zone, Z, as shown in Figure 1. Z shall have a maximum length of 8 mm.The temperature/time characteristic of the glow-plug shall be
34、 agreed between the glow-plug manufacturer and the engine manufacturer.1) 1 bar = 0,1 MPa = 105Pa; 1 MPa = 1 N/mm2.2 ISO 2015 All rights reservedBS ISO 17447-3:2015ISO 17447-3:2015(E)4.4 Electrical resistance at room temperature4.4.1 TestUse a suitable measuring device which does not distort the res
35、istance (e.g. four-pole measuring device).4.4.2 RequirementThe measured resistance shall be as agreed between the glow-plug manufacturer and the engine manufacturer.4.5 Current characteristic4.5.1 TestUse the test installation as specified in 4.3.2. Record the current characteristic by measuring the
36、 initial current, its gradient, and the current at thermal equilibrium.4.5.2 RequirementThe recorded characteristics shall be as agreed between the glow-plug manufacturer and the engine manufacturer.4.6 Higher voltage4.6.1 TestUse the test installation as specified in 4.3.2. Apply a test voltage of
37、130 % of the nominal voltage of the glow-plug for the duration (15 1) s.4.6.2 RequirementAfter the test, the glow-plug shall still meet the requirements of 4.3, 4.4, and 4.5.4.7 Vibration (sinusoidal)4.7.1 TestThe glow-plug, mounted as provided for and tightened as specified, shall be subjected to a
38、 vibration test of type Fc in accordance with the test method in IEC 60068-2-6, using the parameters given in Table 1.Table 1 Values for vibration testFrequency f HzAmplitude mmAcceleration50 f 160 0,3 160 f 500 30 g (294 m/s2)Sweep rate: 1 octave/minVibration directions: glow-plug axis and perpendi
39、cularDuration: 8 h in each direction ISO 2015 All rights reserved 3BS ISO 17447-3:2015ISO 17447-3:2015(E)4.7.2 RequirementAfter the test specified in 4.7.1, the glow-plug shall show no visual damage and shall meet the requirements mutually agreed between the glow-plug manufacturer and the engine man
40、ufacturer.4.8 Endurance4.8.1 TestThe test conditions shall be agreed between the glow-plug manufacturer and the engine manufacturer. The agreed conditions shall include at least the following: number of cycles; voltage characteristic; installation (i.e. in accordance with 4.3.2 or in a simulated cyl
41、inder head); environmental condition (e.g. air speed and temperature); cooling; cycle start temperature.4.8.2 RequirementThe glow-plug manufacturer and the engine manufacturer shall agree on the performance.4.9 Marking and labellingThe glow-plug shall be permanently marked with at least the followin
42、g: the nominal voltage of the glow-plug; the manufacturers name, trademark, or symbol.4 ISO 2015 All rights reservedBS ISO 17447-3:2015BS ISO 17447-3:2015ISO 17447-3:2015(E) ISO 2015 All rights reservedICS 43.060.50Price based on 4 pagesThis page deliberately left blankBSI is the national body respo
43、nsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chi
44、swick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and
45、refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the knowledge that your organization needs to succeed. Find out more about British Standards by visiting
46、our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and international standards, through our website at where hard copies can also be purchased. If you need int
47、ernational and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are designed to make using standards easier for you. For further information on our subscription products go to
48、 British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so youll always be up to date. You can keep in touch with standards developments and receive substantial dis
49、counts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You will automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit
