1、BS ISO18672-1:2009ICS 23.040.20; 23.040.45; 91.140.80; 93.030NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDPlastics piping systemsfor non-pressuredrainage and sewerage Polyester resinconcrete (PRC)Part 1: Pipes and fittings with flexiblejointsThis British Stan
2、dardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 June2009. BSI 2009ISBN 978 0 580 55666 1Amendments/corrigenda issued since publicationDate CommentsBS ISO 18672-1:2009National forewordThis British Standard is the UK implementation of ISO 18672-1:2009.The UK par
3、ticipation in its preparation was entrusted to TechnicalCommittee PRI/88/2, Plastics piping for pressure applications.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contrac
4、t. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS ISO 18672-1:2009Reference numberISO 18672-1:2009(E)ISO 2009INTERNATIONAL STANDARD ISO18672-1First edition2009-06-15Plastics piping systems for non-pressure drainage
5、 and sewerage Polyester resin concrete (PRC) Part 1: Pipes and fittings with flexible joints Systmes de canalisations en plastique pour les branchements et les collecteurs dassainissement sans pression Bton rsines polyester (BRP) Partie 1: Tubes et raccords avec assemblages flexibles BS ISO 18672-1:
6、2009ISO 18672-1:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
7、 downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found i
8、n the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the add
9、ress given below. COPYRIGHT PROTECTED DOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IS
10、O at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedBS ISO 18672-1:2009ISO 18672
11、-1:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Terms, definitions, symbols and abbreviations 2 3.1 Terms and definitions. 2 3.2 Symbols and abbreviations . 6 4 General requirements. 9 4.1 Materials 9 4.2 Appearance . 10 4.3 Reference con
12、ditions for testing. 10 4.4 Joints 10 5 Pipes. 11 5.1 Classification. 11 5.2 Designation . 12 5.3 Geometrical characteristics. 12 5.4 Mechanical characteristics 20 5.5 Marking of pipes . 24 6 Fittings . 24 6.1 General. 24 6.2 Bends . 25 6.3 Branches 28 6.4 Marking of fittings. 30 7 Joint performance
13、. 30 7.1 General. 30 7.2 Requirements 30 Annex A (normative) Test method for the determination of a pipes crushing strength and ring bending tensile strength using a pipe test piece 34 Annex B (normative) Test method for the determination of a pipes crushing strength or ring bending tensile strength
14、 using test pieces sawn from a pipe . 42 Annex C (normative) Test methods for the assessment of longitudinal bending moment resistance 48 Annex D (normative) Test method for the determination of the compressive strength of polyester resin concrete (PRC) using test pieces cut from a pipe. 54 Annex E
15、(normative) Test method for the determination of the fatigue strength of a pipe under cyclic loading 58 Annex F (normative) Method for the assessment of the leaktightness of a pipe and its joints under short-term exposure to internal water pressure. 63 Annex G (normative) Test method for the determi
16、nation of the long-term (50 years) crushing strength of a pipe, including the effects of media attack . 65 BS ISO 18672-1:2009ISO 18672-1:2009(E) iv ISO 2009 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (I
17、SO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, gov
18、ernmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC
19、 Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the membe
20、r bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 18672-1 was prepared by Technical Committee ISO/TC 138, Plastics pipes,
21、fittings and valves for the transport of fluids, Subcommittee SC 6, Reinforced plastics pipes and fittings for all applications. ISO 18672 consists of the following parts, under the general title Plastics piping systems for non-pressure drainage and sewerage Polyester resin concrete (PRC): Part 1: P
22、ipes and fittings with flexible joints BS ISO 18672-1:2009INTERNATIONAL STANDARD ISO 18672-1:2009(E) ISO 2009 All rights reserved 1Plastics piping systems for non-pressure drainage and sewerage Polyester resin concrete (PRC) Part 1: Pipes and fittings with flexible joints 1 Scope This part of ISO 18
23、672 specifies definitions, requirements and characteristics of pipes, fittings, joints, materials, test methods and marking for pipes and fittings made from polyester resin concrete (PRC), intended to be used within a drain or sewer system operating without pressure. It applies to products for use i
24、n buried installations to be installed by open-trench techniques or pipe jacking. It applies to pipes, fittings and their joints of nominal sizes from DN 150 to DN 3000 for circular cross-sections, from WN/HN 300/450 to WN/HN 1400/2100 for egg-shaped cross-sections and from DN 800 to DN 1800 for kit
25、e-shaped cross-sections. The intended use of these products is for the conveyance of sewage, rainwater and surface water at temperatures up to 50 C, without pressure or occasionally at a head of pressure up to 0,5 bar1), and installed in areas subjected to vehicle and/or pedestrian traffic. The pipe
26、s are classified on the basis of the intended method of installation and cross-sectional shape. NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections, taking into account the particular requirements and any relevant national regulations and installation pract
27、ices or codes. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 75-2, P
28、lastics Determination of temperature of deflection under load Part 2: Plastics and ebonite ISO 3126, Plastics piping systems Plastics components Determination of dimensions ISO 7510, Plastics piping systems Glass-reinforced plastics (GRP) components Determination of the amounts of constituents using
29、 the gravimetric method ISO 8639, Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods for leaktightness of flexible joints ISO 10928, Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Methods for regression analysis and their use EN 68
30、1-1, Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber 1) 1 bar = 0,1 MPa = 0,1 N/mm2= 105N/m2BS ISO 18672-1:2009ISO 18672-1:2009(E) 2 ISO 2009 All rights reservedEN 13121-1, GRP tanks and vessels for use above ground Part
31、1: Raw materials Specification conditions and acceptance conditions 3 Terms, definitions, symbols and abbreviations 3.1 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1.1 adaptor fitting that provides for connections to structures, pipes of othe
32、r materials, or valves 3.1.2 angular deflection angle between the axes of two adjacent pipes See Figures 1b) and 1c). NOTE Angular deflection is expressed in degrees (). 3.1.3 bend fitting that provides for a change of alignment within a pipeline 3.1.4 branch fitting comprising a pipe with one addit
33、ional connecting pipe of equal or smaller nominal size, DN or WN/HN, to connect two pipelines NOTE See 3.1.13 and 3.1.14 for DN and WN/HN. 3.1.5 design service temperature maximum sustained temperature at which the system is expected to operate NOTE It is expressed in degrees Celsius (C). 3.1.6 draw
34、 D longitudinal movement of a joint See Figure 1a). NOTE Draw is expressed in millimetres (mm). 3.1.7 laying length of a bend L distance from one end of the bend, excluding the spigot insertion depth, Li, of a socket end, where applicable, projected along the axis of that end of the bend to the poin
35、t of intersection with the axis of the other end of the bend See Figure 8. NOTE Laying length of a bend is expressed in metres (m). BS ISO 18672-1:2009ISO 18672-1:2009(E) ISO 2009 All rights reserved 33.1.8 laying length of a pipe internal barrel length L total length of a pipe, Ltot, minus, where a
36、pplicable, the manufacturers recommended spigot insertion depth, Li, in the socket NOTE 1 The laying length of a pipe is expressed in metres (m). NOTE 2 See 3.1.20 for total pipe length, Ltot. 3.1.9 fitting component comprising an adaptor, bend or branch 3.1.10 flexible joint joint that allows relat
37、ive movement between the components being joined 3.1.11 minimum crushing load qcr,minshort-term load that a component is required to withstand during a crushing strength test, without failure, corresponding to its nominal size, classification and strength class NOTE 1 The minimum crushing load is de
38、termined using Equation (1) or Equation (2), as applicable (see 5.4.1.1). NOTE 2 For the purposes of this part of ISO 18672, it is expressed in newtons per millimetre length (N/mm). 3.1.12 misalignment M amount by which the centre lines of adjacent pipes fail to coincide See Figure 1d). 3.1.13 nomin
39、al size DN alphanumerical designation of size, for a component with a circular or kite-shaped bore NOTE 1 It is a convenient round number for reference purposes and is related to the internal diameter when expressed in millimetres. NOTE 2 The designation for reference or marking purposes consists of
40、 the letters DN plus a number, e.g. DN 600. 3.1.14 nominal size WN/HN alphanumerical designation of size for a component with an egg-shaped bore NOTE 1 It is a convenient round number for reference purposes and is related to the internal width and height (wiand hi, see Figures 3 and 6), expressed in
41、 millimetres. NOTE 2 The designation, for reference or marking purposes, consists of the letters WN/HN plus two numbers, e.g. WN/HN 300/450. 3.1.15 non-pressure pipe or fitting pipe or fitting not subject to an internal pressure greater than 0,5 bar BS ISO 18672-1:2009ISO 18672-1:2009(E) 4 ISO 2009
42、All rights reserved3.1.16 normal service conditions conveyance of surface water, rainwater or sewage, in the temperature range from 2 C to 50 C, without pressure, for 50 years 3.1.17 rerating factor multiplication factor that quantifies the relation between a mechanical, physical or chemical propert
43、y at the service condition and the respective value at 23 C and 50 % relative humidity 3.1.18 strength class Scconstant equal to the minimum short-term crushing load of a component, qcr,min, divided by one thousandth of either its nominal size (DN) or nominal width (WN) NOTE It is expressed in newto
44、ns per millimetre length (N/mm). 3.1.19 total draw Dtotsum of the draw, D, plus the additional longitudinal movement of joint components, J, due to angular deflection, See Figure 1c). NOTE It is expressed in millimetres (mm). 3.1.20 total pipe length Ltotdistance between two planes normal to the pip
45、e axis and passing through the extreme end points of the pipe See Figures 2 to 7. NOTE It is expressed in millimetres (mm). 3.1.21 type tests tests carried out in order to assess the fitness for purpose of a product or assembly of components to fulfil its or their function(s) in accordance with the
46、product specification 3.1.22 crushing load crushing strength qcrmaximum short-term load that a component is able to withstand during a crushing strength test NOTE It is expressed in newtons per millimetre length (N/mm). 3.1.23 polyester resin concrete PRC material formed from mineral aggregates and
47、fillers which are bound together using a polyester resin BS ISO 18672-1:2009ISO 18672-1:2009(E) ISO 2009 All rights reserved 5a) b) c) Figure 1 (continued) BS ISO 18672-1:2009ISO 18672-1:2009(E) 6 ISO 2009 All rights reservedd) Key angular deflection D draw Dtottotal draw J longitudinal movement of
48、the joint due to angular deflection M misalignment Figure 1 Joint movements 3.2 Symbols and abbreviations For the purposes of this part of ISO 18672, the symbols given in Table 1 and abbreviations given in Table 2 apply. Table 1 Symbols Symbol Description Unit Where used abwidth of a bearing strip m
49、m Annexes A and B B laying length of a branch pipe mm 6.3, Figure 9 BBnominal offset (body) length of a branch pipe mm 6.3, Figure 9 Bispigot insertion depth of a branch pipe mm 6.3, Figure 9 b width of a sawn test piece mm 5.4.1.2, Annexes B and E D draw mm 3.1.6, 3.1.19, Figure 1, 7.2.2 Dmaxmaximum draw mm 4.4.2.2, 7.2.2, 7.2.4 Dtottotal draw mm 3.1.19, Figure 1, 7.2.4 daexternal diameter of a pipe mm 5.3.1, Figure 2, 5.3.3 to 5.3.6, Figures 4 to 7, 6.2.1.1, 6.3.1.1 deexternal diam
