BS ISO 3597-4-2003 Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Determination of apparent interlaminar shear.pdf

上传人:王申宇 文档编号:587120 上传时间:2018-12-15 格式:PDF 页数:10 大小:330.45KB
下载 相关 举报
BS ISO 3597-4-2003 Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Determination of apparent interlaminar shear.pdf_第1页
第1页 / 共10页
BS ISO 3597-4-2003 Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Determination of apparent interlaminar shear.pdf_第2页
第2页 / 共10页
BS ISO 3597-4-2003 Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Determination of apparent interlaminar shear.pdf_第3页
第3页 / 共10页
BS ISO 3597-4-2003 Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Determination of apparent interlaminar shear.pdf_第4页
第4页 / 共10页
BS ISO 3597-4-2003 Textile-glass-reinforced plastics - Determination of mechanical properties on rods made of roving-reinforced resin - Determination of apparent interlaminar shear.pdf_第5页
第5页 / 共10页
亲,该文档总共10页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、BRITISH STANDARD BS ISO 3597-4:2003 Textile-glass-reinforced plastics Determination of mechanical properties on rods made of roving-reinforced resin Part 4: Determination of apparent interlaminar shear strength ICS 59.100.10; 83.120 BS ISO 3597-4:2003 This British Standard was published under the au

2、thority of the Standards Policy and Strategy Committee on 30 October 2003 BSI 30 October 2003 ISBN 0 580 42834 6 National foreword This British Standard reproduces verbatim ISO 3597-4:2003 and implements it as the UK national standard. It supersedes BS 2782-10 Method 1008D:1996 which is withdrawn. T

3、he UK participation in its preparation was entrusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British S

4、tandards which implement international publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publica

5、tion does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international

6、/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title pa

7、ge, pages ii to iv, pages 1 to 3 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 3597-4:2003(E)INTERNATIONAL STANDARD ISO 3597-4 Second edition 2003-10-0

8、1 Textile-glass-reinforced plastics Determination of mechanical properties on rods made of roving-reinforced resin Part 4: Determination of apparent interlaminar shear strength Plastiques renforcs verre textile Dtermination des proprits mcaniques sur joncs de stratifils Partie 4: Dtermination de la

9、rsistance en cisaillement interlaminaire apparent BSISO35974:2003ii ISO 3597-4:2003(E) I SO 3002 All irhgts seredevr iiiContents Page Foreword iv 1 Scope 1 2 Normative references. 1 3 Apparatus. 1 4 Preparation and conditioning of test specimens 1 5 Procedure. 2 6 Expression of results 3 7 Precision

10、 3 8 Test report 3 BSISO35974:2003iiiISO 3597-4:2003(E) vi I SO 3002 All irhgts seredevrForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out

11、through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO coll

12、aborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International St

13、andards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements

14、of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 3597-4 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 13, Composites and reinforcement fibres. This second edition cancels and replaces

15、 the first edition (ISO 3597-4:1993), which has been technically revised. ISO 3597 consists of the following parts, under the general title Textile-glass-reinforced plastics Determination of mechanical properties on rods made of roving-reinforced resin: Part 1: General considerations and preparation

16、 of rods Part 2: Determination of flexural strength Part 3: Determination of compressive strength Part 4: Determination of apparent interlaminar shear strength BSISO35974:2003ivINTENRATIONAL TSANDADR IS-7953 O4:(3002E)I SO 3002 All irhgts seredevr 1Textile-glass-reinforced plastics Determination of

17、mechanical properties on rods made of roving-reinforced resin Part 4: Determination of apparent interlaminar shear strength 1 Scope This part of ISO 3597 specifies a method for determining the apparent interlaminar shear strength of composite rods of circular cross-section made of roving-reinforced

18、resin. The test may be carried out on “as-moulded” rods, or on rods that have been pretreated by immersion in boiling water (or another medium) for a specified time. The test is intended for inspection and quality control of rovings or for evaluating their suitability for use in a resin system. The

19、results obtained are not intended for the generation of design data. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced do

20、cument (including any amendments) applies. ISO 3597-1, Textile-glass-reinforced plastics Determination of mechanical properties on rods made of roving-reinforced resin Part 1: General considerations and preparation of rods ISO 14125, Fibre-reinforced plastic composites Determination of flexural prop

21、erties 3 Apparatus 3.1 Flexural-testing apparatus, as specified in ISO 14125, with the following additional characteristics: 3.1.1 The load applicator shall be a steel rod waisted in the middle to ensure a distribution of stresses. A load applicator suitable for a 6-mm-diameter test specimen is show

22、n in Figure 1. It is important that the radius R of the waist is not more than 0,25 mm larger than the actual (measured) radius of the test specimen. 3.1.2 The span between the supports shall be 5 times the diameter of the test specimen. 3.2 Micrometer or vernier gauge, capable of measuring to the n

23、earest 0,1 mm. 4 Preparation and conditioning of test specimens Prepare and condition a given number of specimens in accordance with the method given in ISO 3597-1. For each type of test (“as-moulded” or pretreated), the minimum required number of specimens is eight. If specific statistical limits a

24、re agreed between interested parties, additional specimens may be tested to permit statistical analysis of the results. The required specimen length is 8 times its diameter, i.e. 48 mm for a rod of diameter 6 mm. BSISO35974:20031ISO 3597-4:2003(E) 2 I SO 3002 All irhgts seredevrDimensions in millime

25、tres NOTE When specimens with a different diameter are tested, a load applicator of different dimensions needs to be used. Figure 1 Example of load applicator for testing specimens of diameter 6 mm 5 Procedure 5.1 Before carrying out the interlaminar-shear test, measure the diameter of each test spe

26、cimen with a micrometer or vernier gauge (3.2) to the nearest 0,1 mm at two points around the circumference located 90 apart at the centre of the specimen. Use the average of these two measurements in the calculation of the results. 5.2 Carry out the interlaminar-shear test on the specimens in accor

27、dance with ISO 14125, modified as specified in 3.1, in the same standard laboratory atmosphere as that used for specimen conditioning. The speed of the load applicator shall be 1 mm/min. Continue the test until the specimen fails. Record the maximum force, in newtons, that occurred during the test.

28、The person requiring the test may require that the mode of failure be recorded (see Figure 2). a) Type X (delamination) b) Type Y (splitting) c) Type Z (flexural deformation) aTop view. Figure 2 Acceptable and unacceptable failure modes (Only Type X is acceptable) 5.3 Check that a type X failure mod

29、e is obtained with each specimen. For other failure modes, repeat the test on further specimens. Continue testing until at least five valid results are obtained (see Clause 4). If five valid results are not obtained, prepare and test a further set of specimens. If this second set results in similar

30、difficulties, record this situation in the test report. BSISO35974:20032ISO 3597-4:2003(E) I SO 3002 All irhgts seredevr 36 Expression of results For each test specimen, calculate the apparent interlaminar-shear strength , expressed in megapascals, using the equation: 2 8 F d = 3where F is the break

31、ing force, in newtons; d is the diameter, in millimetres, of the test specimen. 7 Precision The precision of this test method is not known because inter-laboratory data are not available. When inter-laboratory data are obtained, a precision statement will be added at the following revision. 8 Test r

32、eport The test report shall include the following information: a) a reference to this part of ISO 3597; b) all information necessary for complete identification of the roving tested; c) all information necessary for complete identification of the resin used; d) the diameter of the mould used to prep

33、are the test rods; e) whether a release agent was used and, if so, details of the agent used; f) the curing and post-curing conditions; g) the test atmosphere; h) the test results: 1) for “as-moulded” specimens, the glass content, diameter, apparent interlaminar-shear strength and, if required, mode

34、 of failure of each specimen tested and (except for the mode of failure) the average value; 2) if testing was also carried out after pretreatment: the medium used; the length of the pretreatment; the individual and average values of the flexural strength after pretreatment. BSISO35974:20033BS ISO 35

35、97-4:2003 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British

36、 Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while

37、 using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribe

38、rs automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI

39、website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European

40、and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email:

41、infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipb

42、si-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of

43、 the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior wr

44、itten permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.

展开阅读全文
相关资源
  • BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdfBS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf
  • BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdfBS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf
  • BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdfBS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf
  • BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdfBS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf
  • BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdfBS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf
  • BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdfBS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf
  • BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdfBS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf
  • BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdfBS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf
  • BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdfBS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf
  • BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdfBS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > BS

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1