1、BS ISO 3767-3:2016T r a c t o r s , m a c h i n e r y f o ragriculture and forestry,powered lawn and gardenequipment Symbols foroperator controls and otherdisplaysPart 3: Symbols for powered lawn andgarden equipmentBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06BS I
2、SO 3767-3:2016 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 3767-3:2016.It supersedes BS ISO 3767-3:1995 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee AGE/20, Powered lawn and garden equipment.A list of organi
3、zations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2016.Published by BSI Standards Limited 2016ISB
4、N 978 0 580 80479 3ICS 01.080.20; 65.060.70Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 September 2016.Amendments/corrigenda issued since publicationDate T e
5、 x t a f f e c t e dBS ISO 3767-3:2016 ISO 2016Tractors, machinery for agriculture and forestry, powered lawn and garden equipment Symbols for operator controls and other displays Part 3: Symbols for powered lawn and garden equipmentTracteurs, matriels agricoles et forestiers, matriel moteur pour ja
6、rdins et pelouses Symboles pour les commandes de loprateur et autres indications Partie 3: Symboles pour matriel moteur pour jardins et pelousesINTERNATIONAL STANDARDISO3767-3Third edition2016-09-01Reference numberISO 3767-3:2016(E)BS ISO 3767-3:2016ISO 3767-3:2016(E)ii ISO 2016 All rights reservedC
7、OPYRIGHT PROTECTED DOCUMENT ISO 2016, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet,
8、 without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.o
9、rgBS ISO 3767-3:2016ISO 3767-3:2016(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 General 25 Colour . 36 Development of new symbols . 37 Adaptation of symbols as digital display icons . 48 Lawn and garden tractor symbols 49 Riding lawn mower symbols .1010 Grass-cutting
10、 equipment symbols 1011 Tiller symbols .1412 Snow removal equipment symbols 15Bibliography .16 ISO 2016 All rights reserved iiiContents PageBS ISO 3767-3:2016ISO 3767-3:2016(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
11、 member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, gover
12、nmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintena
13、nce are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attentio
14、n is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction an
15、d/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity a
16、ssessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 23, Tractors and machinery for agriculture and forestry, SC 14, Opera
17、tor controls, operator symbols and other displays, operator manuals.This third edition cancels and replaces the second edition (ISO 3767-3:1995), which has been technically revised. Many new symbols have been added.A list of all the parts in the ISO 3767 series can be found on the ISO website.iv ISO
18、 2016 All rights reservedBS ISO 3767-3:2016INTERNATIONAL STANDARD ISO 3767-3:2016(E)Tractors, machinery for agriculture and forestry, powered lawn and garden equipment Symbols for operator controls and other displays Part 3: Symbols for powered lawn and garden equipment1 ScopeThis document standardi
19、zes symbols for use on operator controls and other displays on powered lawn and garden equipment.NOTE 1 ISO 3767-1 covers common symbols that apply to multiple types of agricultural tractors and machinery, forestry machinery, and powered lawn and garden equipment. ISO 3767-2 covers symbols for agric
20、ultural tractors and machinery. ISO 3767-4 covers symbols for forestry machinery. ISO 3767-5 covers symbols for manual portable forestry machines.NOTE 2 ISO 7000 and IEC 60417 can be consulted for additional internationally standardized symbols of potential relevance to powered lawn and garden equip
21、ment.2 Normative referencesThe following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (inclu
22、ding any amendments) applies.ISO 3767-1:2016, Tractors, machinery for agriculture and forestry, powered lawn and garden equipment Symbols for operator controls and other displaysPart 1: Common symbolsIEC 80416-1, Basic principles for graphical symbols for use on equipment Part 1: Creation of graphic
23、al symbols for registrationISO 80416-2, Basic principles for graphical symbols for use on equipment Part 2: Form and use of arrowsIEC 80416-3, Basic principles for graphical symbols for use on equipment Part 3: Guidelines for the application of graphical symbols3 Terms and definitionsFor the purpose
24、s of this document, the following terms and definitions apply.ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at http:/www.electropedia.org/ ISO Online browsing platform: available at http:/www.iso.org/obp ISO 2016 All
25、rights reserved 1BS ISO 3767-3:2016ISO 3767-3:2016(E)3.1symbolgraphical symbolvisually perceptible figure used to transmit information independent of languageNote 1 to entry: It may be produced by drawing, printing or other means. Letters, numerals and mathematical symbols may be used as symbols or
26、symbol elements. For some specific applications, groups of letters (for example, AUTO, STOP) are used as symbols or symbol elements.Note 2 to entry: Letters and numerals are not registered by ISO/TC 145/SC 3 or published in ISO 7000 unless they are symbol elements embedded in graphical symbols.3.2ic
27、ondigital display icondigitized (pixelated) representation of a graphical symbol, usually used on a reconfigurable electronic display screen or graphical user interface (GUI) Note 1 to entry: A single symbol can be represented by multiple icons, each of a different size, pixel count or colourization
28、.4 General4.1 Except where indicated in subsequent clauses, symbols shall be used as shown in this document.4.2 Selected symbols, which are shown in outline form in this document, may be filled in actual use for enhanced clarity of reproduction and improved visual perception by the operator, except
29、as otherwise specified for individual symbols, and in accordance with IEC 80416-3.4.3 Limitations inherent in some reproduction and display technologies can require increased line width or other minor modifications of symbols. Such modifications are allowed, provided that the symbol remains conceptu
30、ally unchanged in its basic graphical elements and is easily discernible by the operator.4.4 To improve the appearance and perceptibility of a graphical symbol, or to coordinate with the design of the equipment to which it is applied, it can be necessary to modify the symbol as indicated in IEC 8041
31、6-3 (for example, to change the line width or to round the corners of the symbol). Such modifications are allowed, provided that the essential perceptible characteristics of the symbol are maintained.4.5 For actual use, all symbols shall be reproduced large enough to be easily discernible by the ope
32、rator. Follow IEC 80416-1 for the proper sizing of symbols. Symbols grouped together in a display or on a set of controls should be scaled to the same degree relative to the corner marks of the symbol original as shown in this document in order to maintain the correct visual relationship among the s
33、ymbols. Symbols shall be used in the orientation shown in this document, unless rotation or mirror imaging is specifically allowed for individual symbols.4.6 Most symbols are constructed using a building block approach in which various symbols and symbol elements are combined in a logical manner to
34、produce a new symbol.4.7 In some cases, symbols may be used in conjunction, without being combined into a composite symbol, to convey the same meaning as the composite symbol.4.8 Symbols are generally intended to replace a word or words with a graphical image that has the same meaning for all operat
35、ors, regardless of their native language. However, the use of a graphical symbol to identify a control or display does not preclude the use of words in conjunction with that control or display.2 ISO 2016 All rights reservedBS ISO 3767-3:2016ISO 3767-3:2016(E)4.9 If a symbol shows a machine or parts
36、of a machine from a side view, a machine moving from right to left across the symbol area shall be assumed. If a symbol shows a machine or parts of a machine from an overhead view, a machine moving from bottom to top across the symbol area shall be assumed.4.10 Symbols on controls and displays shall
37、 have a good contrast to their background. A white or light-coloured symbol on a black or dark-coloured background is preferred for most controls. Displays may use either a white or light-coloured symbol on a black or dark-coloured background or a black or dark-coloured symbol on a white or light-co
38、loured background, depending upon which alternative provides the best visual perception. When a symbol image is reversed (for example, from black-on-white to white-on-black or vice versa) this reversal shall be done for the entire symbol.4.11 If symbols are cast, moulded, embossed or stamped into a
39、surface, the symbols shall be visually distinct from that surface without dependence on colour.4.12 Symbols shall be located on or adjacent to the control or display that is being identified. Where more than one symbol is required for a control, the symbols shall be located in relation to the contro
40、l such that movement of the control towards the symbols shall effect the function depicted by that symbol.4.13 Arrows used in symbols shall conform to the requirements of ISO 80416-2. IEC 80416-1 shall be consulted for the general principles for creating symbol originals. IEC 80416-3 should be consu
41、lted for guidelines for the application of symbols.4.14 ISO/IEC registration numbers are shown for symbols which are registered in ISO 7000 or IEC 60417.NOTE Symbol originals are approved and registered either by ISO/TC 145/SC 3 and published in ISO 7000 or by IEC/SC 3C and published in IEC 60417. I
42、n some cases, modified or application symbols, rather than the registered symbol originals, are standardized in this document.4.15 When letters or numerals are used in a symbol, the font shown shall not be considered definitive. Other fonts may be used so long as the letters and numerals remain legi
43、ble.4.16 Symbols in this document are shown within marks that delimit the corners of the 75 mm square basic pattern from IEC 80416-1. Corner marks are not part of the symbol, but are provided to ensure consistent presentation of all symbol graphics.5 ColourWhen used on illuminated displays, the foll
44、owing colours shall have the meanings indicated: red denotes a failure, serious malfunction or operating condition that requires immediate attention; yellow or amber denotes a condition outside normal operating limits; green denotes a normal operating condition.6 Development of new symbols6.1 Prior
45、to developing a new symbol, a search should be conducted for previously standardized symbols with the same or similar meaning to what is needed. ISO 7000 and IEC 60417 (both available in database form) are compilations of internationally standardized symbols which can be useful both for finding appr
46、opriate symbols that do not appear in ISO 3767 and for generating concepts that can be used in the development of new symbols. ISO 2016 All rights reserved 3BS ISO 3767-3:2016ISO 3767-3:2016(E)6.2 New symbols shall be developed in accordance with the principles of ISO 3767-1:2016, Annex A. IEC 80416
47、-1 should be consulted for general principles for the creation of symbols. Arrows shall be in accordance with ISO 80416-2. Different arrow forms have different meanings according to ISO 80416-2. Care should be taken to use the correct arrow form. Following the guidelines of ISO 3767-1:2016, Annex A
48、makes possible the development of symbols appropriate in graphical form and content for international standardization and ISO 7000 registration.6.3 Symbols proposed for standardization in this document shall include a short explanation of the function or expected use of the symbol.NOTE IEC 80416-1 u
49、ses the term “description” for this type of information and provides guidelines for writing descriptions for symbols intended for standardization in ISO 7000 or IEC 60417. The descriptions for symbols standardized in this document can serve as examples.7 Adaptation of symbols as digital display iconsSymbols can be adapted for use as digital display icons on visual display units, reconfigurable displays or other electronic displays. Such adaptations should follow the principles of ISO 80416-4. Special care should be taken to ens
