1、BSI Standards PublicationBS ISO 5610-2:2014Tool holders with rectangularshank for indexable insertsPart 2: Style ABS ISO 5610-2:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 5610-2:2014. Itsupersedes BS ISO 5610-2:2010 which is withdrawn.The UK participa
2、tion in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract.
3、 Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83610 7ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority
4、of theStandards Policy and Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS ISO 5610-2:2014 ISO 2014Tool holders with rectangular shank for indexable inserts Part 2: Style APorte-plaquette queue rectangulaire pour plaquettes amovibles Partie 2: Forme AINTE
5、RNATIONAL STANDARDISO5610-2Second edition2014-09-01Reference numberISO 5610-2:2014(E)BS ISO 5610-2:2014ISO 5610-2:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized othe
6、rwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeC
7、ase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5610-2:2014ISO 5610-2:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 General . 13.2
8、Tool holder style A for rhombic indexable insert shape C . 23.3 Tool holder style A for triangular indexable insert shape T 44 Designation 65 Material 76 Design 76.1 Type of mounting 76.2 Corner radius, r76.3 Thickness, s, of indexable insert . 77 Extent of delivery . 78 Marking 8Bibliography 9BS IS
9、O 5610-2:2014ISO 5610-2:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interes
10、ted in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical C
11、ommission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO document
12、s should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible
13、for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for th
14、e convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Fo
15、reword - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This second edition cancels and replaces the first edition (ISO 5610-2:2010), of which it constitutes a minor revision.ISO 5610
16、consists of the following parts, under the general title Tool holders with rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part
17、 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style Tiv ISO 2014 All rights reservedBS ISO 5610-2:2014ISO 5610-2:2014(E) Part 14: Style H Part 15: Style V ISO 2014 All rights reserved vBS ISO 5610-2:2014BS ISO 5610-2:2014Tool holders with rectangular shank for indexable ins
18、erts Part 2: Style A1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style A, i.e. with straight shank and cutting edge angle r= 90 for side cutting.These tool holders are primarily intended for indexable inserts made of hard metal or other cutting materials intended to be
19、 mounted by clamping and used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are given in ISO 5610-1:2014, Table A.1.2 Normative referencesThe f
20、ollowing documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5608:2012
21、, Turning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimensions3.1 GeneralIt is not necessary for tool holders to comply with
22、the pictorial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angles and inclination angles shown in the figures are recommended va
23、lues; they can vary according to the application.INTERNATIONAL STANDARD ISO 5610-2:2014(E) ISO 2014 All rights reserved 1BS ISO 5610-2:2014ISO 5610-2:2014(E)3.2 Tool holder style A for rhombic indexable insert shape CKeyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand tool ho
24、lder (R); left-hand tool holder (L) laterally reversed.Figure 1 Tool holder style A for rhombic indexable insert C2 ISO 2014 All rights reservedBS ISO 5610-2:2014ISO 5610-2:2014(E)Table 1Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 +050,h13 k16 max.SCACR 0808 068 8 6,4 8,5 8 12 2,38SCAC
25、L 0808 06SCACR 1010 0610 10 6,4 10,5 10 12 2,38SCACL 1010 06aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For the letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable. ISO 2014
26、 All rights reserved 3BS ISO 5610-2:2014ISO 5610-2:2014(E)3.3 Tool holder style A for triangular indexable insert shape TKeyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 2 Tool holder style A for triangul
27、ar indexable insert T4 ISO 2014 All rights reservedBS ISO 5610-2:2014ISO 5610-2:2014(E)Table 2Dimensions in millimetresSymbolah1js13bh13l3f+050,h2h13l1ak16l2max.sbSTACR 1212 1112 12 11 12,5 12 252,38STACL 1212 11PTANR 1212 113,18PTANL 1212 11CTAPR 1212 11CTAPL 1212 11STACR 1616 1116 16 11 16,5 16 25
28、2,38STACL 1616 11PTANR 1616 113,18PTANL 1616 11CTAPR 1616 11CTAPL 1616 11STACR 2020 1620 20 16,5 20,5 20 323,97STACL 2020 16PTANR 2020 164,76PTANL 2020 16CTAPR 2020 163,18CTAPL 2020 16STACR 2525 1625 25 16,5 25,5 25 323,97STACL 2525 16PTANR 2525 164,76PTANL 2525 16CTAPR 2525 163,18CTAPL 2525 16STACR
29、 3225 1632 25 16,5 25,5 32 323,97STACL 3225 16PTANR 3225 164,76PTANL 3225 16CTAPR 3225 163,18CTAPL 3225 16aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For the letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert t
30、hickness without shim, if applicable. ISO 2014 All rights reserved 5BS ISO 5610-2:2014ISO 5610-2:2014(E)Symbolah1js13bh13l3f+050,h2h13l1ak16l2max.sbSTACR 3232 2232 32 22 33 32 36 4,76STACL 3232 22PTANR 3232 22PTANL 3232 22CTAPR 3232 22CTAPL 3232 22STACR 4040 2240 40 22 41 40 36 4,76STACL 4040 22PTAN
31、R 4040 22PTANL 4040 22CTAPR 4040 22CTAPL 4040 22aFor the selection of length, l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For the letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.4 DesignationA tool h
32、older in accordance with this part of ISO 5610 shall be designated by the following:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. ISO 5610-2);c) type of mounting, in accordance with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style,
33、in accordance with ISO 5608;f) symbol for the indexable insert normal clearance, in accordance with ISO 5608;g) symbol for hand of tool, in accordance with ISO 5608;h) its height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length l3.EXAMPLE 1
34、 Tool holder for a screw-clamped (S) rhombic indexable insert shape C (C), tool holder style A (A), for normal clearance of indexable insert n= 7 (C), right-hand type (R), with height h1= 10 mm, and width b = 10 mm (1010), length l1= 70 mm (E), for cutting edge length l3= 6,4 mm (06) is designated a
35、s follows:Tool holder ISO 5610-2 SCACR 1010 E06EXAMPLE 2 Tool holder for a horizontally mounted, bore-clamped (P) triangular indexable insert shape T (T), tool holder style A (A), normal clearance of indexable insert n= 0 (N), right-hand type (R), with height h1= 32 mm, and width b = 25 mm (3225), l
36、ength l1= 170 mm (P), for cutting edge length l3= 16,5 mm (16) is designated as follows:Tool holder ISO 5610-2 PTANR 3225 P16Table 26 ISO 2014 All rights reservedBS ISO 5610-2:2014ISO 5610-2:2014(E)5 MaterialThe material should be steel with a tensile strength of at least 1 200 N/mm2.6 Design6.1 Typ
37、e of mountingStandard design of tool holders with indexable insert shall be mounted in accordance with Tables 1 and 2.Other types of mounting are at the manufacturers discretion or upon agreement. The letter symbol in the designation, symbol 1, shall then be replaced by the respective symbol for the
38、 chosen or agreed-upon type of mounting, in accordance with ISO 5608.For the modified type of mounting deviating from Tables 1 and 2, the relevant indexable insert thickness shall also be considered.6.2 Corner radius, rTool holders in accordance with this part of ISO 5610 can be equipped with indexa
39、ble inserts with cutting edge length, l3, as specified in Tables 1 and 2, and any corner radius, r.The values for l1given in ISO 5610-1:2014, Table 2 apply to tool holders with indexable inserts having corner radii, r, in accordance with Table 3.Table 3Dimensions in millimetresl3r6,40,41116,50,822NO
40、TE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm and 0,794 mm.For indexable inserts with corner radii, r, other than those specified in Table 3, the dimensions of l1shall be determined in accordance with ISO 5610-1.The tolerances for h1
41、, f, and l1refer to dimensions measured with master indexable insert and master shim, if applicable.6.3 Thickness, s, of indexable insertThe values for thickness, s, given in Tables 1 and 2 apply to indexable inserts without shim and for the standard design of tool holders.For tool holders for index
42、able inserts with thicknesses deviating from the specified values, the thickness shall be indicated when ordering or upon delivery (in the handbook).7 Extent of deliveryThe tool holders shall be delivered complete with clamping device, but without indexable insert(s). ISO 2014 All rights reserved 7B
43、S ISO 5610-2:2014ISO 5610-2:2014(E)8 MarkingTool holders shall be marked with the letter symbol and the name or trademark of the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Deviations in marking may be by mutual agreement.A reference to this part of ISO 5610,
44、 i.e. ISO 5610-2:2014, shall be given on the packaging.8 ISO 2014 All rights reservedBS ISO 5610-2:2014ISO 5610-2:2014(E)Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO 3002-1, Basic quantities in cutting and grinding Part 1: Geo
45、metry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers3 ISO 3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Indexable hard material inserts with rounded corners, with part
46、ly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool items ISO 2014 All rights reserved 9BS ISO 5610
47、-2:2014ISO 5610-2:2014(E) ISO 2014 All rights reservedICS 25.100.01Price based on 9 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. Brit
48、ish Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined e
49、xperience and expertise into standards -based solutions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with the
