1、BSI Standards PublicationBS ISO 5610-5:2014Tool holders with rectangularshank for indexable insertsPart 5: Style FBS ISO 5610-5:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 5610-5:2014. Itsupersedes BS ISO 5610-5:2010 which is withdrawn.The UK participa
2、tion in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract.
3、 Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83613 8ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority
4、of theStandards Policy and Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS ISO 5610-5:2014 ISO 2014Tool holders with rectangular shank for indexable inserts Part 5: Style FPorte-plaquette queue rectangulaire pour plaquettes amovibles Partie 5: Forme FINTE
5、RNATIONAL STANDARDISO5610-5Second edition2014-09-01Reference numberISO 5610-5:2014(E)BS ISO 5610-5:2014ISO 5610-5:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized othe
6、rwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeC
7、ase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5610-5:2014ISO 5610-5:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 General . 13.2
8、Tool holder style F for rhombic indexable insert shape C . 23.3 Tool holder style F for triangular indexable insert shape T . 44 Designation 65 Material 76 Design 76.1 Type of mounting 76.2 Corner radius, r76.3 Thickness, s, of indexable insert . 87 Extent of delivery . 88 Marking 8Bibliography 9BS
9、ISO 5610-5:2014ISO 5610-5:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body inter
10、ested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
11、 Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO docume
12、nts should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsibl
13、e for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for
14、the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL:
15、Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This second edition cancels and replaces the first edition (ISO 5610-5:2010), of which it constitutes a minor revision.ISO 561
16、0 consists of the following parts, under the general title Tool holders with rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Pa
17、rt 9: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style Tiv ISO 2014 All rights reservedBS ISO 5610-5:2014ISO 5610-5:2014(E) Part 14: Style H Part 15: Style V ISO 2014 All rights reserved vBS ISO 5610-5:2014BS ISO 5610-5:2014Tool holders with rectangular shank for indexable i
18、nserts Part 5: Style F1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style F, i.e. with offset shank and cutting edge angle r= 90 for end cutting.These tool holders are primarily intended for indexable inserts made of hard metal or other cutting materials to be mounted b
19、y clamping and to be used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are given in ISO 5610-1:2014, Table A.1.2 Normative referencesThe follo
20、wing documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5608:2012, Tu
21、rning and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimensions3.1 GeneralIt is not necessary for tool holders to comply with the
22、pictorial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angles and inclination angles shown in the figures are recommended values
23、; they can vary according to the application.INTERNATIONAL STANDARD ISO 5610-5:2014(E) ISO 2014 All rights reserved 1BS ISO 5610-5:2014ISO 5610-5:2014(E)3.2 Tool holder style F for rhombic indexable insert shape CKeyaInclination angle, s.bRake angle, o.NOTE The figure shows a right-hand tool holder
24、(R); left-hand tool holder (L) laterally reversed.Figure 1 Tool holder style F for rhombic indexable insert C2 ISO 2014 All rights reservedBS ISO 5610-5:2014ISO 5610-5:2014(E)Table 1Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 +050,h13 k16 max.SCFCR 0808 068 8 6,4 10 8 12 2,38SCFCL 0808
25、 06SCFCR 1010 0610 10 6,4 12 10 12 2,38SCFCL 1010 06aFor the selection of length,l1, the dash can be replaced by the dimensions of ISO 5610-1:2010, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable. ISO 2014 All rights r
26、eserved 3BS ISO 5610-5:2014ISO 5610-5:2014(E)3.3 Tool holder style F for triangular indexable insert shape TKeyaInclination angle, s.bRake angle, o.4 ISO 2014 All rights reservedBS ISO 5610-5:2014ISO 5610-5:2014(E)NOTE The figure shows a right-hand tool holder (R); left-hand tool holder (L) laterall
27、y reversed.Figure 2 Tool holder style F for triangular indexable insert TTable 2Dimensions in millimetresSymbolah1b l3f h2l1al2sbjs13 h13 +050,h13 k16 max.STFCR 1212 1112 12 11 16 12 252,38STFCL 1212 11PTFNR 1212 113,18PTFNL 1212 11CTFPR 1212 11CTFPL 1212 11STFCR 1616 1116 16 11 20 16 252,38STFCL 16
28、16 11PTFNR 1616 113,18PTFNL 1616 11CTFPR 1616 11CTFPL 1616 11STFCR 1616 1616 16 16,5 20 16 323,97STFCL 1616 16PTFNR 1616 164,76PTFNL 1616 16CTFPR 1616 163,18CTFPL 1616 16STFCR 2020 1620 20 16,5 25 20 323,97STFCL 2020 16PTFNR 2020 164,76PTFNL 2020 16CTFPR 2020 163,18CTFPL 2020 16STFCR 2525 1625 25 16
29、,5 32 25 323,97STFCL 2525 16PTFNR 2525 164,76PTFNL 2525 16CTFPR 2525 163,18CTFPL 2525 16aFor the selection of length,l1, the dash can be replaced by the dimensions of ISO 5610-1:2010, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim,
30、if applicable. ISO 2014 All rights reserved 5BS ISO 5610-5:2014ISO 5610-5:2014(E)Symbolah1b l3f h2l1al2sbjs13 h13 +050,h13 k16 max.STFCR 2525 2225 25 22 32 25 36 4,76STFCL 2525 22PTFNR 2525 22PTFNL 2525 22CTFPR 2525 22CTFPL 2525 22STFCR 3225 1632 25 16,5 32 32 323,97STFCL 3225 16PTFNR 3225 164,76PTF
31、NL 3225 16CTFPR 3225 163,18CTFPL 3225 16STFCR 3225 2232 25 22 32 32 36 4,76STFCL 3225 22PTFNR 3225 22PTFNL 3225 22CTFPR 3225 22CTFPL 3225 22STFCR 3232 2232 32 22 40 32 36 4,76STFCL 3232 22PTFNR 3232 22PTFNL 3232 22CTFPR 3232 22CTFPL 3232 22STFCR 4040 2240 40 22 50 40 36 4,76STFCL 4040 22PTFNR 4040 2
32、2PTFNL 4040 22CTFPR 4040 22CTFPL 4040 22PTFNR 4040 2740 40 27,5 50 40 40 6,35PTFNL 4040 27aFor the selection of length,l1, the dash can be replaced by the dimensions of ISO 5610-1:2010, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim
33、, if applicable.4 DesignationA tool holder in accordance with this part of ISO 5610 shall be designated by the following:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. ISO 5610-5);Table 26 ISO 2014 All rights reservedBS ISO 5610-5:2014ISO 5610-5:2014(E)c) type of mounting, in accorda
34、nce with ISO 5608;d) symbol for indexable insert shape, in accordance with ISO 5608;e) symbol for tool style, in accordance with ISO 5608;f) symbol for the indexable insert normal clearance, in accordance with ISO 5608;g) symbol for hand of tool, in accordance with ISO 5608;h) its height, h1, width,
35、 b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length, l3.EXAMPLE 1 Tool holder for a screw-clamped (S) rhombic indexable insert shape C (C), tool holder style F (F), for normal clearance of indexable insert n= 7 (C), right-hand type (R), with height h1= 1
36、0 mm and width b = 10 mm (1010), length l1= 70 mm (E), for cutting edge length l3= 6,4 mm (06) is designated as follows:Tool holder ISO 5610-5 - SCFCR 1010 E06EXAMPLE 2 Tool holder for a horizontally mounted, bore-clamped (P) triangular indexable insert shape T (T), tool holder style F (F), normal c
37、learance of indexable insert n= 0 (N), right-hand type (R), with height h1= 32 mm and width b = 25 mm (3225), length l1= 170 mm (P), for cutting edge length l3= 22 mm (22) is designated as follows:Tool holder ISO 5610-5 - PTFNR 3225 P225 MaterialThe material should be steel with a tensile strength o
38、f at least 1 200 N/mm2.6 Design6.1 Type of mountingStandard design of tool holders with indexable insert shall be mounted in accordance with Tables 1 and 2.Other types of mounting are at the manufacturers discretion or upon agreement. The letter symbol in the designation, symbol 1, shall then be rep
39、laced by the respective symbol for the chosen or agreed-upon type of mounting in accordance with ISO 5608.For the modified type of mounting deviating from Tables 1 and 2, the relevant indexable insert thickness shall also be considered.6.2 Corner radius, rTool holders in accordance with this part of
40、 ISO 5610 can be equipped with indexable inserts with cutting edge lengths, l3, as specified in Tables 1 and 2, and any corner radius, r.The values for l1given in ISO 5610-1:2014, Table 2 apply to tool holders with indexable inserts having corner radii, r, in accordance with Table 3. ISO 2014 All ri
41、ghts reserved 7BS ISO 5610-5:2014ISO 5610-5:2014(E)Table 3Dimensions in millimetresl3r6,40,41116,50,82227,5 1,2NOTE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm, 0,794 mm, and 1,191 mm.For indexable inserts with corner radii r, other t
42、han those specified in Table 3, the dimensions of f shall be determined in accordance with ISO 5610-1.The tolerances for h1, f, and l1refer to dimensions measured with master indexable insert and master shim, if any.6.3 Thickness, s, of indexable insertThe values for thickness, s, given in Tables 1
43、and 2 apply to indexable inserts without shim and for the standard design of tool holders.For tool holders for indexable inserts with thicknesses deviating from the specified values, the thickness shall be indicated when ordering or upon delivery (in the handbook).7 Extent of deliveryTool holders sh
44、all be delivered complete with clamping device, but without indexable insert(s).8 MarkingTool holders shall be marked with the letter symbol and the name or trademark of the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Deviations in marking may be by mutual ag
45、reement.A reference to this part of ISO 5610, i.e. ISO 5610-5:2014, shall be given on the packaging.8 ISO 2014 All rights reservedBS ISO 5610-5:2014ISO 5610-5:2014(E)Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO 3002-1, Basic q
46、uantities in cutting and grinding Part 1: Geometry of the active part of cutting tools General terms, reference systems, tool and working angles, chip breakers3 ISO 3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Indexable hard mat
47、erial inserts with rounded corners, with partly cylindrical fixing hole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool it
48、ems ISO 2014 All rights reserved 9BS ISO 5610-5:2014ISO 5610-5:2014(E) ISO 2014 All rights reservedICS 25.100.01Price based on 9 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and servic
49、es.BSI is incorporated by Royal Charter. British Standards and other standardization products are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovat
