1、BSI Standards PublicationBS ISO 5610-8:2014Tool holders with rectangularshank for indexable insertsPart 8: Style KBS ISO 5610-8:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 5610-8:2014. Itsupersedes BS ISO 5610-8:2010 which is withdrawn.The UK participa
2、tion in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract.
3、 Users are responsible for its correctapplication. The British Standards Institution 2014. Published by BSI StandardsLimited 2014ISBN 978 0 580 83616 9ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority
4、of theStandards Policy and Strategy Committee on 31 August 2014.Amendments issued since publicationDate Text affectedBS ISO 5610-8:2014 ISO 2014Tool holders with rectangular shank for indexable inserts Part 8: Style KPorte-plaquette queue rectangulaire pour plaquettes amovibles Partie 8: Forme KINTE
5、RNATIONAL STANDARDISO5610-8Second edition2014-09-01Reference numberISO 5610-8:2014(E)BS ISO 5610-8:2014ISO 5610-8:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized othe
6、rwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeC
7、ase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 5610-8:2014ISO 5610-8:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative references 13 Dimensions . 13.1 General . 13.2
8、Tool holder style K for rhombic indexable insert shape C . 23.3 Tool holder style K for square indexable insert shape S . 34 Designation 55 Material 66 Design 66.1 Type of mounting 66.2 Corner radius, r66.3 Thickness, s, of indexable insert . 77 Extent of delivery . 78 Marking 7Bibliography 8BS ISO
9、5610-8:2014ISO 5610-8:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body intereste
10、d in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Com
11、mission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents
12、should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible fo
13、r identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the
14、convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Fore
15、word - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools with defined cutting edges, cutting items.This second edition cancels and replaces the first edition (ISO 5610-8:2010), of which it constitutes a minor revision.ISO 5610 co
16、nsists of the following parts, under the general title Tool holders with rectangular shank for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style A Part 3: Style B Part 4: Style D Part 5: Style F Part 6: Style G Part 7: Style J Part 8: Style K Part 9
17、: Style L Part 10: Style N Part 11: Style R Part 12: Style S Part 13: Style Tiv ISO 2014 All rights reservedBS ISO 5610-8:2014ISO 5610-8:2014(E) Part 14: Style H Part 15: Style V ISO 2014 All rights reserved vBS ISO 5610-8:2014BS ISO 5610-8:2014Tool holders with rectangular shank for indexable inser
18、ts Part 8: Style K1 ScopeThis part of ISO 5610 specifies tool holders with rectangular shank, style K, i.e. with offset shank and cutting edge angle r= 75 for end cutting.These tool holders are primarily intended for indexable inserts made of hard metal or other cutting materials to be mounted by cl
19、amping and to be used for turning operations.NOTE The symbols for the dimensions shown in the tables of this part of ISO 5610 and the corresponding preferred symbols of properties defined in ISO/TS 13399-2 and ISO/TS 13399-3 are given in ISO 5610-1:2014, Table A.1.2 Normative referencesThe following
20、 documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5608:2012, Turnin
21、g and copying tool holders and cartridges for indexable inserts DesignationISO 5610-1:2014, Tool holders with rectangular shank for indexable inserts Part 1: General survey, correlation and determination of dimensions3 Dimensions3.1 GeneralIt is not necessary for tool holders to comply with the pict
22、orial representation; only the dimensions given shall be observed.For determination of dimensions h1, f, and l1, see ISO 5610-1.For explanation of the designation code for tool holders, see ISO 5608.NOTE The values of rake angles and inclination angles shown in the figures are recommended values; th
23、ey can vary according to the application.INTERNATIONAL STANDARD ISO 5610-8:2014(E) ISO 2014 All rights reserved 1BS ISO 5610-8:2014ISO 5610-8:2014(E)3.2 Tool holder style K for rhombic indexable insert shape CKeyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand tool holder (R)
24、; left-hand tool holder (L) laterally reversed.Figure 1 Tool holder style K for rhombic indexable insert CTable 1Dimensions in millimetresSymbolah1js13bh13l3af+050,h2h13l1ak16l2max.sbSCKCR 0808 068 8 6,4 1,6 10 8 12 2,38SCKCL 0808 06SCKCR 1010 0610 10 6,4 1,6 12 10 12 2,38SCKCL 1010 06aFor the selec
25、tion of length l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickness without shim, if applicable.2 ISO 2014 All rights reservedBS ISO 5610-8:2014ISO 5610-8:2014(E)3.3 Tool holder style
26、K for square indexable insert shape SKeyaInclination angle, s.bRake angle, o.NOTE This figure shows a right-hand tool holder (R); left-hand tool holder (L) laterally reversed.Figure 2 Tool holder style K for square indexable insert S ISO 2014 All rights reserved 3BS ISO 5610-8:2014ISO 5610-8:2014(E)
27、Table 2Dimensions in millimetresSymbolah1js13bh13l3af+050,h2h13l1ak16l2max.sbSSKCR 1212 0912 12 9,52 2,2 16 12 323,97SSKCL 1212 09PSKNR 1212 093,18PSKNL 1212 09CSKPR 1212 09CSKPL 1212 09SSKCR 1616 0916 16 9,52 2,2 20 16 323,97SSKCL 1616 09PSKNR 1616 093,18PSKNL 1616 09CSKPR 1616 09CSKPL 1616 09SSKCR
28、 1616 1216 16 12,7 3,1 20 16 364,76SSKCL 1616 12PSKNR 1616 12PSKNL 1616 12CSKPR 1616 123,18CSKPL 1616 12SSKCR 2020 1220 20 12,7 3,1 25 20 364,76SSKCL 2020 12PSKNR 2020 12PSKNL 2020 12CSKPR 2020 123,18CSKPL 2020 12SSKCR 2525 1225 25 12,7 3,9 32 25 364,76SSKCL 2525 12PSKNR 2525 12PSKNL 2525 12CSKPR 25
29、25 123,18CSKPL 2525 12SSKCR 2525 1525 25 15,88 4,6 32 25 405,56SSKCL 2525 15PSKNR 2525 156,35PSKNL 2525 15aFor the selection of length l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.bInsert thickn
30、ess without shim, if applicable.4 ISO 2014 All rights reservedBS ISO 5610-8:2014ISO 5610-8:2014(E)Symbolah1js13bh13l3af+050,h2h13l1ak16l2max.sbCSKPR 2525 1925 25 19,05 4,6 32 25 45 4,76CSKPL 2525 19SSKCR 3225 1232 25 12,7 3,9 32 32 364,76SSKCL 3225 12PSKNR 3225 12PSKNL 3225 12CSKPR 3225 123,18CSKPL
31、3225 12SSKCR 3225 1532 25 15,88 4,6 32 32 405,56SSKCL 3225 15PSKNR 3225 156,35PSKNL 3225 15CSKPR 3225 1932 25 19,05 4,6 32 32 45 4,76CSKPL 3225 19SSKCR 3232 1932 32 19,05 4,6 40 32 456,35SSKCL 3232 19PSKNR 3232 19PSKNL 3232 19CSKPR 3232 194,76CSKPL 3232 19SSKCR 4040 1940 40 19,05 4,6 50 40 456,35SSK
32、CL 4040 19PSKNR 4040 19PSKNL 4040 19CSKPR 4040 194,76CSKPL 4040 19PSKNR 4040 2540 40 25,4 5,9 50 40 50 7,94PSKNL 4040 25aFor the selection of length l1, the dash can be replaced by the dimensions of ISO 5610-1:2014, Table 2. For letter symbols identifying the tool length, see ISO 5608:2012, Table 6.
33、bInsert thickness without shim, if applicable.4 DesignationA tool holder in accordance with this part of ISO 5610 shall be designated by the following:a) “Tool holder”;b) a reference to this part of ISO 5610 (i.e. ISO 5610-8);c) type of mounting, in accordance with ISO 5608;d) symbol for indexable i
34、nsert shape, in accordance with ISO 5608;Table 2 ISO 2014 All rights reserved 5BS ISO 5610-8:2014ISO 5610-8:2014(E)e) symbol for tool style, in accordance with ISO 5608;f) symbol for the indexable insert normal clearance, in accordance with ISO 5608;g) symbol for hand of tool, in accordance with ISO
35、 5608;h) its height, h1, width, b, and length, l1(symbol for tool length in accordance with ISO 5608);i) its cutting edge length, l3.EXAMPLE 1 Tool holder for a screw-clamped (S) rhombic indexable insert shape C (C), tool holder style K (K), for normal clearance of indexable insert n= 7 (C), right-h
36、and type (R), with height h1= 10 mm and width b = 10 mm (1010), length l1= 70 mm (E), for cutting edge length l3= 6,4 mm (06) is designated as follows:Tool holder ISO 5610-8 - SCKCR 1010 E06EXAMPLE 2 Tool holder for a horizontally mounted, top-clamped (C) square indexable insert shape S (S), tool ho
37、lder style K (K), normal clearance of indexable insert n= 11 (P), right-hand type (R), with height h1= 32 mm and width b = 25 mm (3225), length l1= 170 mm (P), for cutting edge length l3= 19,05 mm (19) is designated as follows:Tool holder ISO 5610-8 - CSKPR 3225 P195 MaterialThe material should be s
38、teel with a tensile strength of at least 1 200 N/mm2.6 Design6.1 Type of mountingStandard design of tool holders with indexable insert shall be mounted in accordance with Tables 1 and 2.Other types of mounting are at the manufacturers discretion or upon agreement. The letter symbol in the designatio
39、n, symbol 1, shall then be replaced by the respective symbol for the chosen or agreed-upon type of mounting in accordance with ISO 5608.For the modified type of mounting deviating from Tables 1 and 2, the relevant indexable insert thickness shall also be considered.6.2 Corner radius, rTool holders i
40、n accordance with this part of ISO 5610 can be equipped with indexable inserts with cutting edge length, l3, as specified in Tables 1 and 2, and any corner radius, r.The values for l1given in ISO 5610-1:2014, Table 2, apply to tool holders with indexable inserts having corner radii, r, in accordance
41、 with Table 3.Table 3Dimensions in millimetresl3r6,4 0,49,520,812,7NOTE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm, 0,794 mm, 1,191 mm, and 2,381 mm.6 ISO 2014 All rights reservedBS ISO 5610-8:2014ISO 5610-8:2014(E)l3r15,881,219,0525
42、,4 2,4NOTE The values given for rare nominal values. The accurate values converted from the inch dimensions are 0,397 mm, 0,794 mm, 1,191 mm, and 2,381 mm.For indexable inserts with corner radii, r, other than those specified in Table 3, the dimensions of a, f, and l1shall be determined in accordanc
43、e with ISO 5610-1.The tolerances for h1, f, and l1refer to dimensions measured with master indexable insert and master shim, if applicable.6.3 Thickness, s, of indexable insertThe values for thickness, s, given in Tables 1 and 2, apply to indexable inserts without shim and for the standard design of
44、 tool holders.For tool holders for indexable inserts with thicknesses deviating from the specified values, the thickness shall be indicated when ordering or upon delivery (in the handbook).7 Extent of deliveryTool holders shall be delivered complete with clamping device, but without indexable insert
45、(s).8 MarkingTool holders shall be marked with the letter symbol and the name or trademark of the manufacturer.Additional marking is at the manufacturers discretion or upon agreement.Deviations in marking may be by mutual agreement.A reference to this part of ISO 5610, i.e. ISO 5610-8:2014, shall be
46、 given on the packaging.Table 3 ISO 2014 All rights reserved 7BS ISO 5610-8:2014ISO 5610-8:2014(E)Bibliography1 ISO 883, Indexable hardmetal (carbide) inserts with rounded corners, without fixing hole Dimensions2 ISO 3002-1, Basic quantities in cutting and grinding Part 1: Geometry of the active par
47、t of cutting tools General terms, reference systems, tool and working angles, chip breakers3 ISO 3364, Indexable hardmetal (carbide) inserts with rounded corners, with cylindrical fixing hole Dimensions4 ISO 6987, Indexable hard material inserts with rounded corners, with partly cylindrical fixing h
48、ole Dimensions5 ISO/TS 13399-2, Cutting tool data representation and exchange Part 2: Reference dictionary for the cutting items6 ISO/TS 13399-3, Cutting tool data representation and exchange Part 3: Reference dictionary for tool items8 ISO 2014 All rights reservedBS ISO 5610-8:2014BS ISO 5610-8:201
49、4ISO 5610-8:2014(E) ISO 2014 All rights reservedICS 25.100.01Price based on 8 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Stand
