1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 603-18:2013Bonded abrasive products DimensionsPart 18: Grinding wheels for flat glass edgegrinding machinesBS ISO 603-18:2013 BRITISH STANDARDNational forewordThis British
2、 Standard is the UK implementation of ISO 603-18:2013.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/13, Grinding wheels, abrasive tools, paper andcloths, and powders.A list of organizations represented on this committee can beobtained on request to its secretary.Thi
3、s publication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 72516 6ICS 25.100.70Compliance with a British Standard cannot confer imm
4、unity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 January 2013.Amendments issued since publicationDate Text affectedBS ISO 603-18:2013 ISO 2013Bonded abrasive products Dimensions Part 18: Grinding wheels for flat g
5、lass edge grinding machinesProduits abrasifs agglomrs Dimensions Partie 18: Meules pour machines meuler les bords de verre platINTERNATIONAL STANDARDISO603-18First edition2013-01-15Reference numberISO 603-18:2013(E)BS ISO 603-18:2013ISO 603-18:2013(E)ii ISO 2013 All rights reservedCOPYRIGHT PROTECTE
6、D DOCUMENT ISO 2013All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member
7、 body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 603-18:2013ISO 603-18:2013(E) ISO 2013 All rights reserved iiiContents PageForeword iv1 Scope . 1
8、2 Normative references 13 Requirements 13.1 Shapes and dimensions . 13.2 Designation 63.3 Specifications 6BS ISO 603-18:2013ISO 603-18:2013(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of prepa
9、ring International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in l
10、iaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of
11、technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is d
12、rawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights.ISO 603-18 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 5, Grinding wheels and abrasi
13、ves.ISO 603 consists of the following parts, under the general title Bonded abrasive products Dimensions: Part 1: Grinding wheels for external cylindrical grinding between centres Part 2: Grinding wheels for centreless external cylindrical grinding Part 3: Grinding wheels for internal cylindrical gr
14、inding Part 4: Grinding wheels for surface grinding/peripheral grinding Part 5: Grinding wheels for surface grinding/face grinding Part 6: Grinding wheels for tool and tool room grinding Part 7: Grinding wheels for manually guided grinding Part 8: Grinding wheels for deburring and fettling/snagging
15、Part 9: Grinding wheels for high-pressure grinding Part 10: Stones for honing and superfinishings Part 11: Hand finishing sticks Part 12: Grinding wheels for deburring and fettling on a straight grinder Part 13: Grinding wheels for deburring and fettling on a vertical grinder Part 14: Grinding wheel
16、s for deburring and fettling/snagging on an angle grinder Part 15: Grinding wheels for cutting-off on stationary or mobile cutting-off machines Part 16: Grinding wheels for cutting-off on hand held power tools Part 17: Mounted wheels Part 18: Grinding wheels for flat glass edge grinding machinesiv I
17、SO 2013 All rights reservedBS ISO 603-18:2013INTERNATIONAL STANDARD ISO 603-18:2013(E)Bonded abrasive products Dimensions Part 18: Grinding wheels for flat glass edge grinding machines1 ScopeThis part of ISO 603 specifies the shapes, dimensions and limit deviations, in millimetres, of grinding wheel
18、s for flat glass edge grinding machines.This type of bonded abrasive wheel is intended to be used on stationary machines where the position of the grinding wheel is fixed and the workpiece is guided by hand or guided mechanically, or on a stationary machine where the grinding wheel is guided mechani
19、cally and the workpiece is fixed. The common maximum operating speed, vs, for this type of bonded abrasive product is vs 50 m/s2 Normative referencesThe following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated referenc
20、es, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 525, Bonded abrasive products General requirementsISO 6103, Bonded abrasive products Static balancing of grinding wheels TestingISO 13942, Bonded abrasive
21、products Limit deviations and run-out tolerances3 Requirements3.1 Shapes and dimensions3.1.1 Straight wheel, type 1See Figure 1 and Table 1.Figure 1 Straight wheel, type 1 ISO 2013 All rights reserved 1BS ISO 603-18:2013ISO 603-18:2013(E)Table 1 Straight wheels, type 1Dimensions in millimetresD T H1
22、00 10 22,00100 15 22,00100 20 22,00100 25 22,00100 30 22,00120 10 22,00120 15 22,00120 20 22,00120 25 22,00120 30 22,00150 15 22,00150 20 22,00150 25 22,00150 30 22,00200 20 60,00200 25 60,00200 30 60,00200 15 90,00200 20 90,00200 25 90,00200 30 90,00200 40 90,00250 20 50,00250 25 50,00250 30 50,003
23、.1.2 Straight cup wheel, type 6See Figure 2 and Table 2.Figure 2 Straight cup wheel, type 62 ISO 2013 All rights reservedBS ISO 603-18:2013ISO 603-18:2013(E)Table 2 Straight cup wheels, type 6Dimensions in millimetresD T H W E100 30 50,00 20 7100 35 50,00 20 7100 40 11,00 20 8100 40 50,00 20 7100 45
24、 11,00 20 8100 45 50,00 20 8125 35 22,00 20 10130 35 22,00 22,5 10130 35 50,00 22,5 10130 35 70,00 22,5 10130 39 11,00 22,5 10130 40 50,00 22,5 10150 30 50,00 22,5 12150 30 70,00 22,5 12150 35 25,00 22,5 12150 35 50,00 22,5 12150 35 70,00 22,5 12150 40 22,00 22,5 12150 40 25,00 22,5 12150 40 50,00 2
25、2,5 12150 40 68,00 22,5 12150 40 70,00 22,5 12170 40 68,00 22,5 123.1.3 Disc wheel, cemented, type 35See Figure 3 and Table 3.Figure 3 Disc wheel, cemented, type 35 ISO 2013 All rights reserved 3BS ISO 603-18:2013ISO 603-18:2013(E)Table 3 Disc wheels, cemented, type 35Dimensions in millimetresD T H1
26、00 25 50,00200 40 120,003.1.4 Straight wheel, type 1 with profileSee Figure 4 and Table 4.NOTE This is a special profile, not defined in ISO 525.Figure 4 Straight wheel, type 1 with profile4 ISO 2013 All rights reservedBS ISO 603-18:2013ISO 603-18:2013(E)Table 4 Straight wheels, type 1 with profileD
27、imensions in millimetresD T H Profile angle140 4 22,00 12140 5 22,00 12140 6 22,00 12140 8 22,00 12140 10 22,00 12150 4 22,00 12150 5 22,00 12150 6 22,00 12150 8 22,00 12150 10 22,00 12150 4 60,00 12150 5 60,00 12150 6 60,00 12150 8 60,00 12150 10 60,00 12160 4 90,00 12160 5 90,00 12160 6 90,00 1216
28、0 8 90,00 12160 10 90,00 12200 6 60,00 12200 8 60,00 12200 10 60,00 12200 6 90,00 12200 8 90,00 12200 10 90,00 12220 6 60,00 12220 8 60,00 12220 10 60,00 12NOTE Table 4 describes a special profile, which is not defined in ISO 525. ISO 2013 All rights reserved 5BS ISO 603-18:2013ISO 603-18:2013(E)3.2
29、 DesignationA complete designation of a bonded abrasive product in accordance with this part of ISO 603 shall consist of the following information:a) designation of the bonded abrasive, grinding wheel for flat glass edge grinding machine;b) reference of this part of ISO 603, i.e. ISO 603-18;c) shape
30、;d) type;e) dimensions D, T, H, W, E;f) specification mark;maximum operating speed.in accordancee with ISO 525 and this part of ISO 603.EXAMPLE A grinding wheel for flat glass edge grinding machine, Type 1, diameter D = 200 mm, thickness T = 20 mm, bore H = 90,00 mm, nature of abrasive AA, grit size
31、 120, grade of hardness B, structure 5, bond type R and a maximum operating speed of 32 m/s is designated as follows:Grinding wheel for flat glass edge grinding machines ISO 603-18, 1 - 200 20 90 - AA120 B5R - 32 m/s3.3 Specifications3.3.1 TolerancesLimit deviations and run-out tolerances shall be i
32、n accordance with ISO 13942.3.3.2 UnbalanceUnbalance shall be in accordance with ISO 6103.3.3.3 MarkingMarking of grinding wheels for flat glass edge grinding machines shall be in accordance with ISO 525.6 ISO 2013 All rights reservedBS ISO 603-18:2013BS ISO 603-18:2013ISO 603-18:2013(E) ISO 2013 Al
33、l rights reservedICS 25.100.70Price based on 6 pagesThis page deliberately left blankBSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the internat
34、ional level. BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.British Standards Institution (BSI)raising standards worldwideBSI389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards
35、and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy
36、 or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers BSI Subscribi
37、ng Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acre
38、dit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, BSI will supply the British Sta
39、ndard implementation of the relevant international standard, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: BSI Subscribi
40、ng Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to
41、British Standards and PASs via British Standards Online can be found at information about British Standards is available on the BSI website at www.bsi- the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or som
42、e person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, store
43、d in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.Tel: +44 (0)20 8996 7070Email:
