1、BSI Standards PublicationBS ISO 6361-3:2014Wrought aluminium andaluminium alloys Sheets,strips and platesPart 3: Strips: Tolerances on shape anddimensionsBS ISO 6361-3:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6361-3:2014. The UK participation in its
2、 preparation was entrusted to TechnicalCommittee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for
3、its correct application. The British Standards Institution 2014.Published by BSI Standards Limited 2014ISBN 978 0 580 84686 1 ICS 77.150.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy
4、 and Strategy Committee on 30 September 2014.Amendments/corrigenda issued since publicationDate T e x t a f f e c t e d ISO 2014Wrought aluminium and aluminium alloys Sheets, strips and plates Part 3: Strips: Tolerances on shape and dimensionsAluminium et alliages daluminium corroys Tles, bandes et
5、tles paisses Partie 3: Bandes: Tolrances sur forme et dimensionsINTERNATIONAL STANDARDISO 6361-3Third edition 2014-09-15Reference number ISO 6361-3:2014(E)BS ISO 6361-3:2014ISO 6361-3:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise spe
6、cified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or
7、ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 6361-3:2014ISO 6361-3:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv
8、1 Scope . 12 Dimensional tolerances 12.1 Thickness . 12.2 Width . 33 Shape tolerances . 3Bibliography 5BS ISO 6361-3:2014ISO 6361-3:2014(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparin
9、g International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liai
10、son with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Dire
11、ctives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that so
12、me of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declar
13、ations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information abo
14、ut ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information.The committee responsible for this document is ISO/TC 79, Light metals and their alloys, Subcommittee SC 6, Wrought aluminium and aluminium alloys.This third e
15、dition cancels and replaces the second edition (ISO 6361-3:2011), which has been technically revised.ISO 6361 consists of the following parts, under the general title Wrought aluminium and aluminium alloys Sheets, strips and plates: Part 1: Technical conditions for inspection and delivery Part 2: Me
16、chanical properties Part 3: Strips: Tolerances on shape and dimensions Part 4: Sheets and plates: Tolerances on shape and dimensions Part 5: Chemical compositioniv ISO 2014 All rights reservedBS ISO 6361-3:2014INTERNATIONAL STANDARD ISO 6361-3:2014(E)Wrought aluminium and aluminium alloys Sheets, st
17、rips and plates Part 3: Strips: Tolerances on shape and dimensions1 ScopeThis part of ISO 6361 specifies the tolerances on shape and dimensions for wrought aluminium and aluminium alloy strip by cold-rolling for general engineering applications.It applies to products with thickness of over 0,15 mm u
18、p to, and including 16 mm.It does not apply to semi-finished rolled products in coiled form to be subjected to further rolling (reroll stock), or to special products such as those that are corrugated or embossed.Technical conditions for inspection and delivery of products covered by this part of ISO
19、 6361 are specified in ISO 6361-1.2 Dimensional tolerances2.1 ThicknessThickness tolerances shall be in accordance with Tables 1 and 2.When the tolerance is specified as either all plus, or minus side, the value in Table 1, or in Table 2, shall be doubled.Tolerances for the products exceeding the ra
20、nge of specified thickness and width shall be agreed upon by the purchaser and the supplier.Table 1 Thickness tolerancesDimensions in millimetresSpecified thicknessAlloy number1050, 1050A, 1070, 1070A, 1080, 1080A, 1085, 1100, 1200, 1100A, 1230A, 3003, 3103, 3203, 3005, 3105, 4006, 4007, 4015, 5005,
21、 5010, 5110A, 5050, 8011A, 8021, 8079Specified widthOverUp to and includingUp to and including 450Over 450, up to and including 900Over 900, up to and including 1 400Over 1 400, up to and including 1 800Over 1 800, up to and including 2 300Over 2 300, up to and including 2 600Tolerance 0,15 0,20 0,0
22、3 0,03 0,050,20 0,25 0,03 0,04 0,050,25 0,45 0,04 0,04 0,05 0,060,45 0,70 0,04 0,05 0,06 0,080,70 0,90 0,05 0,05 0,06 0,09 0,13 ISO 2014 All rights reserved 1BS ISO 6361-3:2014ISO 6361-3:2014(E)Specified thicknessAlloy number1050, 1050A, 1070, 1070A, 1080, 1080A, 1085, 1100, 1200, 1100A, 1230A, 3003
23、, 3103, 3203, 3005, 3105, 4006, 4007, 4015, 5005, 5010, 5110A, 5050, 8011A, 8021, 8079Specified widthOverUp to and includingUp to and including 450Over 450, up to and including 900Over 900, up to and including 1 400Over 1 400, up to and including 1 800Over 1 800, up to and including 2 300Over 2 300,
24、 up to and including 2 600Tolerance0,90 1,1 0,05 0,06 0,08 0,10 0,131,1 1,7 0,06 0,08 0,10 0,13 0,151,7 1,9 0,06 0,08 0,10 0,15 0,201,9 2,4 0,08 0,08 0,10 0,15 0,202,4 2,7 0,09 0,10 0,13 0,18 0,232,7 3,6 0,11 0,11 0,13 0,18 0,23 0,253,6 4,5 0,15 0,15 0,20 0,23 0,28 0,304,5 5,0 0,18 0,18 0,23 0,28 0,
25、33 0,385,0 6,5 0,23 0,23 0,28 0,33 0,38 0,436,5 8,0 0,33 0,33 0,33 0,38 0,43 0,518,0 11 0,48 0,48 0,48 0,48 0,58 0,6611 16 0,64 0,64 0,64 0,64 0,76 0,89Table 2 Thickness tolerancesDimensions in millimetresSpecified thicknessAlloy number2014, 2014A, 2017, 2017A, 2219, 2024, 2124,2 618A, 3004, 3104, 5
26、021, 5026, 5040, 5042, 5049, 5052, 5059, 5070, 5449, 5251, 5154, 5154A, 5254, 5383, 5454, 5754, 5456, 5082, 5182, 5083, 5086, 6016, 6025, 6061, 6082, 7204, 7010, 7020, 7021, 7022, 7050, 7075, 7475, 7178Specified widthOverUp to and includ-ingUp to and includ-ing 450Over 450, up to and includ-ing 900O
27、ver 900, up to and includ-ing 1 200Over 1 200, up to and includ-ing 1 400Over 1 400, up to and includ-ing 1 500Over 1 500, up to and includ-ing 1 700Over 1 700, up to and includ-ing 1 800Over 1 800, up to and includ-ing 2 000Over 2 000, up to and includ-ing 2 100Over 2 100, up to and includ-ing 2 30
28、0Over 2 300, up to and includ-ing 2 400Over 2 400, up to and includ-ing 2 600Tolerance 0,20 0,25 0,03 0,04 0,06 0,060,25 0,45 0,04 0,04 0,06 0,090,45 0,70 0,04 0,05 0,06 0,09 0,10 0,10 0,100,70 0,90 0,05 0,05 0,06 0,10 0,13 0,13 0,13 0,150,90 1,1 0,05 0,06 0,08 0,10 0,13 0,13 0,13 0,151,1 1,7 0,06 0
29、,08 0,10 0,13 0,15 0,15 0,15 0,181,7 1,9 0,08 0,08 0,10 0,13 0,15 0,15 0,15 0,181,9 2,4 0,09 0,09 0,10 0,13 0,15 0,15 0,15 0,18 0,18 0,302,4 2,7 0,10 0,10 0,13 0,13 0,18 0,18 0,18 0,20 0,20 0,412,7 3,2 0,11 0,11 0,13 0,13 0,18 0,18 0,18 0,20 0,20 0,41 0,46 0,51Table 1 (continued)2 ISO 2014 All right
30、s reservedBS ISO 6361-3:2014ISO 6361-3:2014(E)Specified thicknessAlloy number2014, 2014A, 2017, 2017A, 2219, 2024, 2124,2 618A, 3004, 3104, 5021, 5026, 5040, 5042, 5049, 5052, 5059, 5070, 5449, 5251, 5154, 5154A, 5254, 5383, 5454, 5754, 5456, 5082, 5182, 5083, 5086, 6016, 6025, 6061, 6082, 7204, 701
31、0, 7020, 7021, 7022, 7050, 7075, 7475, 7178Specified widthOverUp to and includ-ingUp to and includ-ing 450Over 450, up to and includ-ing 900Over 900, up to and includ-ing 1 200Over 1 200, up to and includ-ing 1 400Over 1 400, up to and includ-ing 1 500Over 1 500, up to and includ-ing 1 700Over 1 700
32、, up to and includ-ing 1 800Over 1 800, up to and includ-ing 2 000Over 2 000, up to and includ-ing 2 100Over 2 100, up to and includ-ing 2 300Over 2 300, up to and includ-ing 2 400Over 2 400, up to and includ-ing 2 600Tolerance3,2 3,6 0,11 0,11 0,13 0,13 0,18 0,25 0,30 0,33 0,36 0,41 0,46 0,513,6 4,
33、5 0,15 0,15 0,20 0,20 0,23 0,30 0,36 0,38 0,41 0,43 0,48 0,584,5 5,0 0,18 0,18 0,25 0,25 0,28 0,36 0,41 0,43 0,43 0,43 0,56 0,665,0 6,5 0,23 0,23 0,28 0,28 0,33 0,41 0,46 0,46 0,46 0,46 0,61 0,716,5 8,0 0,33 0,33 0,33 0,33 0,38 0,46 0,51 0,51 0,51 0,51 0,64 0,768,0 11 0,48 0,48 0,48 0,48 0,51 0,51 0
34、,58 0,58 0,64 0,64 0,66 0,8411 16 0,64 0,64 0,64 0,64 0,64 0,64 0,64 0,76 0,76 0,76 0,89 0,892.2 WidthWidth tolerances shall be in accordance with Table 3.When the tolerance is specified as either all plus, or minus side, the value in Table 3 shall be doubled.Tolerances for the products exceeding th
35、e range of specified thickness and width shall be agreed upon by the purchaser and the supplier.Table 3 Width tolerance for stripDimensions in millimetresSpecified thickness Specified widthOverUp to and includingUp to and including 150Over 150, up to and including 300Over 300, up to and including 60
36、0Over 600, up to and including 1 200Over 1 200, up to and including 1 500Over 1 500, up to and including 2 600Tolerance 0,15 3,2 0,3 0,4 0,8 1,2 1,6 3,23,2 5,0 0,3 0,5 0,8 1,6 2,45,0 6,3 0,4 0,8 1,2 2,4 3,23 Shape tolerancesThe lateral curvature is the depth of the arc for any 2 000 mm basis lengths
37、 (see Figure 1).Table 2 (continued) ISO 2014 All rights reserved 3BS ISO 6361-3:2014ISO 6361-3:2014(E)Keya deviation from straightness (maximum value)b widthc 2 000 mmFigure 1 Lateral curvature of stripWhen tested with the strip resting on a flat surface, against a straight edge, the lateral curvatu
38、re shall not exceed the values given in Table 4 for a value of length L = 2 000 mm.The maximum value for the products exceeding the range of specified thickness and width shall be agreed upon between the purchaser and the supplier.Table 4 Lateral curvature tolerances for stripDimensions in millimetr
39、esSpecified thickness Specified widthOverUp to and including15 or over, up to and including 25Over 25, up to and including 50Over 50, up to and including 100Over 100, up to and including 250Over 250, up to and including 2 600Maximum value (in any 2 000 length) 0,15 1,6 19 15 10 7 51,6 3,2 10 7 54 IS
40、O 2014 All rights reservedBS ISO 6361-3:2014ISO 6361-3:2014(E)Bibliography1 ISO 6361-1, Wrought aluminium and aluminium alloys Sheets, strips and plates Part 1: Technical conditions for inspection and delivery ISO 2014 All rights reserved 5BS ISO 6361-3:2014ISO 6361-3:2014(E) ISO 2014 All rights res
41、ervedICS 77.150.10Price based on 5 pagesThis page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services.BSI is incorporated by Royal Charter. British Standards and other standardization products
42、are published by BSI Standards Limited.British Standards Institution (BSI)BSI Group Headquarters389 Chiswick High Road London W4 4AL UKAbout usWe bring together business, industry, government, consumers, innovators and others to shape their combined experience and expertise into standards -based sol
43、utions.The knowledge embodied in our standards has been carefully assembled in a dependable format and refined through our open consultation process. Organizations of all sizes and across all sectors choose standards to help them achieve their goals.Information on standardsWe can provide you with th
44、e knowledge that your organization needs to succeed. Find out more about British Standards by visiting our website at or contacting our Customer Services team or Knowledge Centre.Buying standardsYou can buy and download PDF versions of BSI publications, including British and adopted European and in
45、ternational standards, through our website at where hard copies can also be purchased. If you need international and foreign standards from other Standards Development Organizations, hard copies can be ordered from our Customer Services team.SubscriptionsOur range of subscription services are desig
46、ned to make using standards easier for you. For further information on our subscription products go to British Standards Online (BSOL) youll have instant access to over 55,000 British and adopted European and international standards from your desktop. Its available 24/7 and is refreshed daily so yo
47、ull always be up to date. You can keep in touch with standards developments and receive substantial discounts on the purchase price of standards, both in single copy and subscription format, by becoming a BSI Subscribing Member. PLUS is an updating service exclusive to BSI Subscribing Members. You w
48、ill automatically receive the latest hard copy of your standards when theyre revised or replaced. To find out more about becoming a BSI Subscribing Member and the benefits of membership, please visit a Multi-User Network Licence (MUNL) you are able to host standards publications on your intranet. Licences can cover as few or as many users as you wish. With updates supplied as soon as theyre available, you can be sure your documentation is current. F
