1、BSI Standards PublicationBS ISO 6362-2:2014Wrought aluminium andaluminium alloys Extrudedrods/bars, tubes and profilesPart 2: Mechanical propertiesBS ISO 6362-2:2014 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6362-2:2014.The UK participation in its prepara
2、tion was entrusted to Technical Committee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its cor
3、rect application. The British Standards Institution 2014. Published by BSI Standards Limited 2014ISBN 978 0 580 84688 5 ICS 23.040.15; 77.150.10 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards P
4、olicy and Strategy Committee on 30 September 2014.Amendments/corrigenda issued since publicationDate Text affected ISO 2014Wrought aluminium and aluminium alloys Extruded rods/bars, tubes and profiles Part 2: Mechanical propertiesAluminium et alliages daluminium corroys Barres, tubes et profils fils
5、 Partie 2: Caractristiques mcaniquesINTERNATIONAL STANDARDISO 6362-2Fourth edition 2014-09-15Reference number ISO 6362-2:2014(E)BS ISO 6362-2:2014ISO 6362-2:2014(E)ii ISO 2014 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2014All rights reserved. Unless otherwise specified, no part of this pub
6、lication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the cou
7、ntry of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandBS ISO 6362-2:2014ISO 6362-2:2014(E) ISO 2014 All rights reserved iiiContents PageForeword iv1 Scope . 12 Normative refe
8、rences 13 Terms and definitions . 14 Tensile testing . 15 Mechanical properties 1Annex A (normative) Rules for rounding 22Annex B (normative) List of tempers used in Tables 1 to 3 23Bibliography .25BS ISO 6362-2:2014ISO 6362-2:2014(E)ForewordISO (the International Organization for Standardization) i
9、s a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represe
10、nted on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop
11、 this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IE
12、C Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the
13、development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of
14、ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 79, Light m
15、etals and their alloys, Subcommittee SC 6, Wrought aluminium and aluminium alloys.This fourth edition cancels and replaces the third edition (ISO 6362-2:2012), which has been technically revised.ISO 6362 consists of the following parts, under the general title Wrought aluminium and aluminium alloys
16、Extruded rods/bars, tubes and profiles : Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Extruded rectangular bars Tolerances on shape and dimensions Part 4: Profiles Tolerances on shape and dimensions Part 5: Round, square and hexagonal bars Tolerances
17、 on shape and dimensions Part 6: Round, square, rectangular and hexagonal tubes Tolerances on shape and dimensions Part 7: Chemical compositioniv ISO 2014 All rights reservedBS ISO 6362-2:2014INTERNATIONAL STANDARD ISO 6362-2:2014(E)Wrought aluminium and aluminium alloys Extruded rods/bars, tubes an
18、d profiles Part 2: Mechanical properties1 ScopeThis part of ISO 6362 specifies the mechanical properties of wrought aluminium and aluminium alloy extruded rods/bars, tubes, and profiles for general engineering applications.It applies to extruded products.2 Normative referencesThe following documents
19、, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 6362-1, Wrought aluminium a
20、nd aluminium alloys Extruded rods/bars, tubes and profiles Part 1: Technical conditions for inspection and deliveryISO 6892-1, Metallic materials Tensile testing Part 1: Method of test at room temperatureASTM B557M, Standard Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-A
21、lloy Products3 Terms and definitionsFor the purposes of this document, the terms and definitions given in ISO 6362-1 apply.4 Tensile testingFor the selection of the specimens and tensile testing, see ISO 6892-1 or ASTM B557M.5 Mechanical propertiesValues for mechanical properties of aluminium and al
22、uminium alloys are given in Tables 1 to 3.For elongation, two different gauge lengths are used. The choice of the gauge length for elongation measurements (A or A50mm) is at the discretion of the producer, unless otherwise agreed.NOTE A is the percentage elongation on a gauge length of 5,65 So. A50m
23、mis the percentage elongation on a gauge length of 50 mm.Test results shall be rounded in accordance with the rules given in Annex A. ISO 2014 All rights reserved 1BS ISO 6362-2:2014ISO 6362-2:2014(E)Table 1 Mechanical properties of rods/barsAlloy Temper DimensionsaTensile strength RmMPa0,2 % proof
24、stress Rp0,2MPaElongation min.min. max. min. max.A %A50mm%1070 H112 All 55 15 -1070A H112 All 60 20 25 231060 H112 3 D or S 30 60 30 251050 H112 All 65 20 1050AH112 D 35 or S 30 65 20 25 23OH111All 60 95 20 25 231350bH112 All 60 25 231100 H112D 35 or S 3035 D or 30 S7575202018181200 H112D 35 or S 30
25、35 D or 30 S7575252020182007T4T4510T4511D or S 8080 D or S 200200 D or S 25037034033025022021088762011T33 D or S 4040 D or S 5050 D or S 75310295290260235205101010101214T4 3 D or S 200 275 125 14 16T63 D or S 7575 D or S 16031029523019586108T8 3 D or S 75 370 275 10 102011AT4 D 200, S 60 275 125 14
26、12T6D 75, S 6075 D 200310295230195866OcAll 250 135 10 122014 T4T4510T4511All 345 240 10 12T42dAll 345 205 12T6T6510T6511D or S 1212 D or S 1919 D or S, A 16 00019 D or S, 16 000 A 20 00019 D or S, 20 000 A 25 00019 D or S, 25 000 A 30 00041044047047045043036540041040038036566666777666T62eD or S 1919
27、 D or S, A 16 00019 D or S, 16 000 A 20 0004104104103653653657762 ISO 2014 All rights reservedBS ISO 6362-2:2014ISO 6362-2:2014(E)Alloy Temper DimensionsaTensile strength RmMPa0,2 % proof stress Rp0,2MPaElongation min.min. max. min. max.A %A50mm%2014AO 10 D or S 200 250 135 10 12T4,T4510T451110 D or
28、 S 200 345 240 10 12T6T6510T651112,5 D or S 100100 D or S 120120 D or S 2004404304304003503506662017OcAll 245 125 - 16T4T42dA 70 00070 000 A 100 00034534521519512122017A O 10 D or S 100 250 150 10 T4T4510T451110 D or S 8080 D or S 200390360265220107OcAll 245 125 10 12T3510T3511D or S 66 D or S 1919
29、D or S 3838 D or S, A 16 00038 D or S, 16 000 A 20 000390410450480470295300310365335108771212101082024T3T4D or S 66 D or S 1919 D or S 3838 D or S 100, A 16 00038 D or S 100, 16 000 A 20 00038 D or S 100, 20 000 A 30 000100 D or S 200, A 16 000100 D or S 200, 16 000 A 20 000100 D or S 200, 20 000 A
30、30 00039041045048047046048047046029530531536533531536533531588866612121010881088T42dD or S 1919 D or S 3838 D or S, A 16 00038 D or S, 16 000 A 20 0003903903903902652652652651210108T8510T8511T8110 D or S 150 455 400 4 2030T4T4510T4511D or S 8080 D or S 200200 D or S 2503703403302502202108876Table 1
31、(continued) ISO 2014 All rights reserved 3BS ISO 6362-2:2014ISO 6362-2:2014(E)Alloy Temper DimensionsaTensile strength RmMPa0,2 % proof stress Rp0,2MPaElongation min.min. max. min. max.A %A50mm%3102 H112 All 80 30 25 233003H112 All 95 35 OH111All 95 135 35 25 203103H112 All 95 35 25 20OH111All 95 13
32、5 35 25 205005 5005AH112 All 100 40 18 16OH111D 80, S 60 100 150 40 18 165019H112 D or S 200 250 110 14 12OH111D or S 200 250 320 110 15 135049 H112 All 180 80 15 135051AH112 All 150 50 16 14OH111All 150 200 50 18 165251H112 All 160 60 16 14OH111All 160 220 60 17 155052H112 All 175 70 O All 175 245
33、70 205154AH112 D or S 200 200 85 16 14OH111D or S 200 200 275 85 18 165454H112 All 215 100 12OH111D or S 200 200 275 85 18 165754H112D or S 150150 D or S 2501801808070141312OH111D or S 150 180 250 80 17 155056 H112A 30 00030 000 A 70 00070 000 A 100 00024522521510080705083H112 D or S 130, A 20 000 2
34、75 140 12 12O D or S 130, A 20 000 275 355 110 145086H112 D or S 250 240 95 12 10O D or S 200 240 320 95 18 15Table 1 (continued)4 ISO 2014 All rights reservedBS ISO 6362-2:2014ISO 6362-2:2014(E)Alloy Temper DimensionsaTensile strength RmMPa0,2 % proof stress Rp0,2MPaElongation min.min. max. min. ma
35、x.A %A50mm%6101T6f3 D or S 77 D or S 1717 D or S 30195195175165165145101214T7 3 D or S 17 135 110 106101A T6fD or S 150 200 170 10 86101BT6f,gS 15 215 160 8 6T7f,hS 15 170 120 12 1060056005AT6fD or S 2525 D or S 5050 D or S 100270270260225225215108886005CT5D or S 66 D or S 1224522520517588T6fD or S
36、6 265 235 86110AT5fD or S 120 380 360 10 8T6fD 120 or S 150 410 380 10 86012T6fT6510fT6511fD or S 150150 D or S 2003102602602008866018T6fT6510fT6511fD or S 150150 D or S 2003102602602008866023T6fT6510fT6511fD or S 150 320 270 10 86351OH111D or S 200 160 110 14 12T4fD or S 200 205 110 14 12T6fD or S
37、2020 D or S 7575 D or S 150150 D or S 200200 D or S 2502953003102802702502552602402008886666060T4fD or S 150 120 60 16 14T5 D or S 150 160 120 8 6T6fD or S 100 190 150 10 8T64fD or S 50 180 120 12 10T66fD or S 150 215 160 8 6Table 1 (continued) ISO 2014 All rights reserved 5BS ISO 6362-2:2014ISO 636
38、2-2:2014(E)Alloy Temper DimensionsaTensile strength RmMPa0,2 % proof stress Rp0,2MPaElongation min.min. max. min. max.A %A50mm%6360T4fD or S 150 110 50 16 14T5 D or S 150 150 110 8 6T6fD or S 150 185 140 8 6T66fD or S 150 195 150 8 66061OcAll 145 110 16T4fT4511All 180 110 14 16T42dAll 175 85 16T6fT6
39、2eT6511D or S 66 D or S260260240240798106261OH111D or S 100 170 120 14 12T4fD or S 100 180 100 14 12T6fD or S 2020 D or S 1002902902452458876262 T6fD or S 200 260 240 10 86262A T6fD 220 or S 155 260 240 10 8OH111D or S 200 130 18 16T1D or S 1212 D or S 25120110605512126063 T4fD or S 150150 D or S 20
40、01301206565141212T5D or S 1212 D or S 251501451101057788T6fD or S 33 D or S 252052051701709810T66fD or S 200 245 200 10 8OH111D or S 200 150 16 146063A T4fD or S 150150 D or S 2001501409090121010T5 D or S 200 200 160 7 5T6fD or S 150150 D or S 2002302201901607756463T4fD or S 150 125 75 14 12T5 D or
41、S 150 150 110 8 6T6fD or S 150 195 160 10 8Table 1 (continued)6 ISO 2014 All rights reservedBS ISO 6362-2:2014ISO 6362-2:2014(E)Alloy Temper DimensionsaTensile strength RmMPa0,2 % proof stress Rp0,2MPaElongation min.min. max. min. max.A %A50mm%6065 T6fD 220 or S 155 260 240 10 86081 T6fD or S 250 27
42、5 240 8 66082OH111D or S 200 160 110 14 12T4f10 D or S 80 205 110 14 14T6f10 D 60 or 10 S 5060 D 150 or 50 S 1503103002602408876182T4fD 220 or S 155 205 110 12 10T6f,i9 D or S 100100 D or S 150150 D or S 2203603302803303002409867647003T5D or S 1212 D or S 252852752452351010T6fD or S 5050 D or S 1503
43、503402902801010887204O All 245 145 12T4jAll 315 195 11T6 All 335 275 107005 T6fD or S 5050 D or S 200350340290270101087108 T6fD or S 100 310 260 10 87108AT6fD or S 200 310 260 12 10T66fD or S 5050 D or S 200350340290275101087020 T6fD or S 5050 D or S 200350340290275101087021 T6fD or S 40 410 350 10
44、87022T6fT6510fT6511fD or S 8080 D or S 2004904704204007757049AT6T6510T6511D or S 100100 D or S 125125 D or S 150150 D or S 180610560520450530500430400555347050T73511 D or S 125, A 20 000 485 415 7 8T74511 D or S 76 505 435 7T76510 D or S 127 545 475 7Table 1 (continued) ISO 2014 All rights reserved
45、7BS ISO 6362-2:2014ISO 6362-2:2014(E)Alloy Temper DimensionsaTensile strength RmMPa0,2 % proof stress Rp0,2MPaElongation min.min. max. min. max.A %A50mm%7075OcA 20 000 275 165 9 10T6,T62eT6510T6511D or S 66 D or S 7575 D or S 110, A 13 00075 D or S 110, 13 000 A 20 000110 D or S 130, A 20 000130 D or S 1505405605605405405004805004904804704406555577776T73k10 D or S 2525 D or S 5050 D or S 7070 D or S 1004854754754704204054053907776T73510kT73511kD or S 2525 D or S 7575 D or S 100100 D or S 15048547547044042040539036077665aD (mm) = diameter for round bar.S (mm) = width across
