1、Rubber compounding ingredients Abbreviated termsBS ISO 6472:2017BSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06 ISO 2017Rubber compounding ingredients Abbreviated termsIngrdients de mlange du caoutchouc Termes abrgsINTERNATIONAL STANDARDISO6472Fifth edition2017-06Re
2、ference numberISO 6472:2017(E)National forewordThis British Standard is the UK implementation of ISO 6472:2017. It supersedes BS ISO 6472:2010, which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/10, Terminology for rubbers and plastics.A list of organ
3、izations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 201
4、7ISBN 978 0 580 92772 0ICS 01.040.83; 83.040.20Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 July 2017.Amendments/corrigenda issued since publicationDate T
5、ext affected BRITISH STANDARDBS ISO 6472:2017 ISO 2017Rubber compounding ingredients Abbreviated termsIngrdients de mlange du caoutchouc Termes abrgsINTERNATIONAL STANDARDISO6472Fifth edition2017-06Reference numberISO 6472:2017(E)BS ISO 6472:2017ISO 6472:2017(E)ii ISO 2017 All rights reservedCOPYRIG
6、HT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, witho
7、ut prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS I
8、SO 6472:2017ISO 6472:2017(E)ii ISO 2017 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in SwitzerlandAll rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, includ
9、ing photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +
10、41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgISO 6472:2017(E)Foreword iv1 Scope . 12 Normative references 13 Terms and definitions . 14 Notation conventions used in this document . 15 Accelerators, co-agents and vulcanizing agents 16 Activators and process aids . 87 Vulcanization re
11、tarders 88 Antidegradants, antioxidants and antiozonants . 98.1 Naming conventions for bisphenol antidegradants 98.2 Abbreviated terms and names of antidegradants, antioxidants and antiozonants . 99 Plasticizers and softeners 129.1 Naming conventions 129.2 Abbreviated terms and names of plasticizers
12、 and softeners .1210 Blowing agents.1411 Isocyanates 15Bibliography .17 ISO 2017 All rights reserved iiiContents PageBS ISO 6472:2017ISO 6472:2017(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work o
13、f preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmenta
14、l, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intended for its further maintenance are described in the IS
15、O/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).Attention is drawn to the possib
16、ility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of
17、patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and expressions related t
18、o conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber prod
19、ucts.This fifth edition cancels and replaces the fourth edition (ISO 6472:2010), which has been technically revised.The main changes compared to the previous edition are as follows: the word symbols has been removed from the title and the scope as there are no symbols being introduced in the standar
20、d; new ingredients and their abbreviations have been added; N,N-ditolyl-p-phenylenediamine (DTPD) has been removed from Table 5 due to its hazardous properties.iv ISO 2017 All rights reservedBS ISO 6472:2017ISO 6472:2017(E)ForewordISO (the International Organization for Standardization) is a worldwi
21、de federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on tha
22、t committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this docum
23、ent and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directive
24、s, Part 2 (see www .iso .org/ directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the developm
25、ent of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the voluntary nature
26、 of standards, the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html.This docu
27、ment was prepared by Technical Committee ISO/TC 45, Rubber and rubber products.This fifth edition cancels and replaces the fourth edition (ISO 6472:2010), which has been technically revised.The main changes compared to the previous edition are as follows: the word symbols has been removed from the t
28、itle and the scope as there are no symbols being introduced in the standard; new ingredients and their abbreviations have been added; N,N-ditolyl-p-phenylenediamine (DTPD) has been removed from Table 5 due to its hazardous properties.iv ISO 2017 All rights reserved INTERNATIONAL STANDARD ISO 6472:20
29、17(E)Rubber compounding ingredients Abbreviated terms1 ScopeThis document establishes unambiguous abbreviated terms for commonly used rubber compounding ingredients of known, specific chemical composition.2 Normative referencesThere are no normative references in this document.3 Terms and definition
30、sNo terms and definitions are listed in this document. ISO and IEC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp4 Nota
31、tion conventions used in this document4.1 The abbreviated terms are derived from common usage in industry and commerce rather than from any systematic nomenclature. The list is not intended to conflict with, but rather to act as a supplement to, existing trade names and trademarks.4.2 When abbreviat
32、ed terms first appear in a text, they shall be enclosed in parentheses and shall be preceded by the chemical name written in full.4.3 The list does not purport to be comprehensive, and abbreviated terms for other compounding ingredients will be added in future revisions of this document.4.4 Internat
33、ional Union of Pure and Applied Chemistry (IUPAC) nomenclature is provided where this is available, in addition to the commonly used chemical name or names. In some instances, alternative commonly used chemical names are given where they are recognized. For those materials whose chemical formula can
34、not be specified, such as reaction products or polymerized products, the identification of IUPAC is “not possible”. Chemical Abstracts Service Registry Number (CAS RN) is also provided unless “not available”.4.5 Unlike ISO 1043-3, which uses the letter F for phosphates, this document uses the letter
35、 P, because P is used universally to designate phosphates and other phosphorous compounds and the letter F is used universally to designate fluorine and its compounds; this usage would thus minimize the confusion among those using this document.5 Accelerators, co-agents and vulcanizing agentsSee Tab
36、le 1. ISO 2017 All rights reserved 1BS ISO 6472:2017ISO 6472:2017(E)Table 1 Accelerators, co-agents and vulcanizing agentsNumber Abbreviated termCommon chemical name, IUPAC name and CAS RN (where available)1 AB ammonium benzoate IUPAC: ammonium benzoate CAS RN: 18636342 BA butyraldehyde-aniline cond
37、ensate IUPAC: not possible CAS RN: 684112013 BiDMC bismuth dimethyldithiocarbamate IUPAC: bismuth tris(dimethyldithiocarbamate) CAS RN: 212604684 BPO benzoyl peroxide IUPAC: dibenzoyl peroxide CAS RN: 943605 BPV n-butyl bis(4,4-tert-butylperoxy)valerate; 3,3-bis(tert-butylperoxy)butane carboxylic ac
38、id n-butyl ester IUPAC: butyl 4,4-bis(tert-butyldioxy)valerate CAS RN: 9953356 BQD p-benzoquinone dioxime IUPAC: p-benzoquinone dioxime CAS RN: 1051137 CBS N-cyclohexylbenzothiazole-2-sulfenamide; N-cyclohexylbenzothiazyl sulfenamide IUPAC: N-cyclohexyl-1,3-benzothiazole-2-sulfenamide CAS RN: 953308
39、 CdDEC cadmium diethyldithiocarbamate IUPAC: cadmium bis(diethyldithiocarbamate) CAS RN: 142396809 CdDMC cadmium dimethyldithiocarbamate IUPAC: cadmium bis(dimethyldithiocarbamate) CAS RN: 1494960110 CuDMC copper dimethyldithiocarbamate IUPAC: copper bis(dimethyldithiocarbamate) CAS RN: 13729111 CLD
40、 caprolactam disulfide IUPAC: 1,1-dithiobis(hexahydro-2H-azepin-2-one) CAS RN: 2384708712 CMBT dicyclohexylammonium 1,3-benzothiazole-2-thiolate IUPAC: dicyclohexylammonium 1,3-benzothiazole-2-thiolate CAS RN: 3743720013 DBA dibenzylamine IUPAC: dibenzylamine CAS RN: 10349114 DBPC 1,1-bis(tert-butyl
41、peroxy)-3,5,5-trimethylcyclohexane; 1,3,3-trimethyl-5,5-di-tert-butylperoxycyclohexane IUPAC: di-tert-butyl 3,3,5-trimethylcyclohexylidene diperoxide CAS RN: 673136815 DBQD p,pnull-dibenzoyl-p-benzoquinone dioxime; quinone dioxime dibenzoate IUPAC: p-benzoquinone bis(O-benzoyloxime) CAS RN: 12052516
42、 DBTU 1,3-dibutylthiourea IUPAC: 1,3-dibutyl-2-thiourea CAS RN: 10946617 DBXD dibutylxanthogen disulfide IUPAC: O,O-dibutyl dithiobis(thioformate) CAS RN: 1057712 ISO 2017 All rights reservedBS ISO 6472:2017ISO 6472:2017(E)Table 1 Accelerators, co-agents and vulcanizing agentsNumber Abbreviated term
43、Common chemical name, IUPAC name and CAS RN (where available)1 AB ammonium benzoate IUPAC: ammonium benzoate CAS RN: 18636342 BA butyraldehyde-aniline condensate IUPAC: not possible CAS RN: 684112013 BiDMC bismuth dimethyldithiocarbamate IUPAC: bismuth tris(dimethyldithiocarbamate) CAS RN: 212604684
44、 BPO benzoyl peroxide IUPAC: dibenzoyl peroxide CAS RN: 943605 BPV n-butyl bis(4,4-tert-butylperoxy)valerate; 3,3-bis(tert-butylperoxy)butane carboxylic acid n-butyl ester IUPAC: butyl 4,4-bis(tert-butyldioxy)valerate CAS RN: 9953356 BQD p-benzoquinone dioxime IUPAC: p-benzoquinone dioxime CAS RN: 1
45、051137 CBS N-cyclohexylbenzothiazole-2-sulfenamide; N-cyclohexylbenzothiazyl sulfenamide IUPAC: N-cyclohexyl-1,3-benzothiazole-2-sulfenamide CAS RN: 953308 CdDEC cadmium diethyldithiocarbamate IUPAC: cadmium bis(diethyldithiocarbamate) CAS RN: 142396809 CdDMC cadmium dimethyldithiocarbamate IUPAC: c
46、admium bis(dimethyldithiocarbamate) CAS RN: 1494960110 CuDMC copper dimethyldithiocarbamate IUPAC: copper bis(dimethyldithiocarbamate) CAS RN: 13729111 CLD caprolactam disulfide IUPAC: 1,1-dithiobis(hexahydro-2H-azepin-2-one) CAS RN: 2384708712 CMBT dicyclohexylammonium 1,3-benzothiazole-2-thiolate
47、IUPAC: dicyclohexylammonium 1,3-benzothiazole-2-thiolate CAS RN: 3743720013 DBA dibenzylamine IUPAC: dibenzylamine CAS RN: 10349114 DBPC 1,1-bis(tert-butylperoxy)-3,5,5-trimethylcyclohexane; 1,3,3-trimethyl-5,5-di-tert-butylperoxycyclohexane IUPAC: di-tert-butyl 3,3,5-trimethylcyclohexylidene dipero
48、xide CAS RN: 673136815 DBQD p,pnull-dibenzoyl-p-benzoquinone dioxime; quinone dioxime dibenzoate IUPAC: p-benzoquinone bis(O-benzoyloxime) CAS RN: 12052516 DBTU 1,3-dibutylthiourea IUPAC: 1,3-dibutyl-2-thiourea CAS RN: 10946617 DBXD dibutylxanthogen disulfide IUPAC: O,O-dibutyl dithiobis(thioformate
49、) CAS RN: 1057712 ISO 2017 All rights reserved ISO 6472:2017(E)Number Abbreviated termCommon chemical name, IUPAC name and CAS RN (where available)18 DCBP 2,4-dichlorobenzoyl peroxide IUPAC: bis(2,4-dichlorobenzoyl) peroxide CAS RN: 13314219 DCBS N,N-dicyclohexylbenzothiazole-2-sulfenamide; N,N-dicyclohexylbenzothiazyl sulfenamide IUPAC: N,N-cyclohexyl-1,3-benzothiazole-2-sulfenamide CAS RN: 497932220 DCP dicumyl peroxide IUPAC: bis(1
