1、BRITISH STANDARD BS ISO 9760:2000 Aerospace Fork- ends, in corrosion- resistant steel, swaged on aircraft control wire rope, for rolling bearings Dimensions and loads ICS 49.035 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBS ISO 9760:2000 This British Standard, having been
2、prepared under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 May 2001 BSI 05-2001 ISBN 0 580 37391 6 National foreword This British Standard reproduces verbatim ISO 9760:2000 and implements it as the UK nat
3、ional standard. The UK participation in its preparation was entrusted to Technical Committee ACE/12/1, Aerospace fasteners, fastening systems, details and parts (International), which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its s
4、ecretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electro
5、nic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understan
6、d the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a
7、front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 4, an inside back cover and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date CommentsA Refe
8、rencenumbe r ISO9760:2000 (E) INTERNATIONAL STANDARD ISO 9760 Firstedition 20001215 AerospaceForkends,incorrosion resistantsteel,swagedonaircraftcontrol wirerope,forrollingbearings Dimensionsandloads AronautiqueetespaceEmboutschape,pourroulementsrouleaux, enacierrsistantlacorrosion,sertirsurcblesdec
9、ommande daronefsDimensionsetchargesISO9760:2000(E) ii t tOISO9760:2000(E) iii Foreword ISO(theInternationalOrganizationforStandardization)isaworldwidefederationofnationalstandardsbodies(ISO memberbodies).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnical committees.Eachm
10、emberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas therighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnongovernmental,in liaisonwithISO,alsotakepartinthework.ISOcollaboratescloselywiththeInternationalElectrotechnical Commission(IEC)onallmatter
11、sofelectrotechnicalstandardization. InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/IECDirectives,Part3. DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtothememberbodiesforvoting. PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthemembe
12、rbodiescastingavote. InternationalStandardISO9760waspreparedbyTechnicalCommitteeISO/TC20, Aircraftandspacevehicles, SubcommitteeSC12, Mechanicalsystemparts . AnnexAformsanormativepartofthisInternationalStandard.INTERNATIONALSTANDARD OISO9760:2000(E) 1 AerospaceForkends,incorrosionresistantsteel,swag
13、edon aircraftcontrolwirerope,forrollingbearingsDimensionsand loads 1Scope ThisInternationalStandardspecifiesthecharacteristicsofforkendsforrollingbearingsincorrosionresistantsteel swagedonaircraftcontrolwirerope. 2Normative references Thefollowingnormativedocumentscontainprovisionswhich,throughrefer
14、enceinthistext,constituteprovisionsofthis InternationalStandard.Fordatedreferences,subsequentamendmentsto,orrevisionsof,anyofthesepublicationsdo notapply.However,partiestoagreementsbasedonthisInternationalStandardareencouragedtoinvestigatethe possibilityofapplyingthemostrecenteditionsofthenormatived
15、ocumentsindicatedbelow.Forundatedreferences, thelatesteditionofthenormativedocumentreferredtoapplies.MembersofISOandIECmaintainregistersof currentlyvalidInternationalStandards. ISO20201:1997, Aerospace Preformedflexiblesteelwireropeforaircraftcontrols Part 1:Dimensionsand loads. ISO8074:1985, Aerosp
16、aceSurfacetreatmentofausteniticstainlesssteelparts. ISO10955:1999, AerospaceEndfittingsandturnbarrelsforaircraftcontrolwireropeTechnicalspecification . ISO13715:2000, TechnicaldrawingsEdgesofundefinedshapeVocabularyandindicationondrawings. EN2465: 1) , AerospaceseriesSteelFEPA11SoftenedBars D e 100m
17、m . 2) SAEAMS2431/6A, PeeningMedia,GlassShot. SAEAMS5639G, Steel,CorrosionResistant,Bars,Wire,Forgings,TubingandRings,19Cr10Ni,SolutionHeat Treated. SAEAMS5641F, Steel,CorrosionResistant,Bars,Wire,andForgings,18.5Cr10Ni0.22SeFreeMachining; SwagingorUpsetting,SolutionHeatTreated. 3 Configuration,dime
18、nsions,loadsandmasses Configuration,dimensions,loadsandmassesshallbeinaccordancewithFigure1andTable1. 4Material Corrosionresistantsteel(inaccordancewithannexA). 1) Tobepublished. 2) AECMA.ISO9760:2000(E) 2 Dimensionsinmillimetres Surfaceroughnessinmicrometres a Marking Figure1OISO9760:2000(E) 3 Tabl
19、e1 Dimensionsinmillimetres Wirerope a D 1 b D 2 D 3 D 4 D 5 D 6 EFHL 1 L 2 L 3 T Mass g/piece Minimum breakingload a Code Nominal diameter - + 02 5 060 , , H8 -012 0 , 0 012 + , 0 02 5 + , -015 0 , H11 h11 0 02 5 + , 0,5 0,5 -05 0 , kN 16 1,6 5 4,1 2 2,3 3,5 12 60 27 0,15 20,6 2,15 24 2,4 19 5,6 2,8
20、 3 4,8 7 1 65 25 22,9 4,45 32 3,2 6 6,4 3,6 3,9 5,6 14 73 32,8 8,9 40 4 20 7,5 4,4 4,8 6,4 8 15 80 26 28 38,3 12,45 48 4,8 25 8 9,1 5,2 5,6 8 9 16 91 31 33 0,2 60,6 18,6 56 5,6 10,9 6 6,5 9,5 1,5 96 71,8 24,9 64 6,4 29 10 12,6 6,8 7,4 11 10 18 105 32,5 35 99,5 31,2 a InaccordancewithISO 20201. b Afa
21、ultintheshapeofthesphericalsurfaceofradius D 1 /2ispermittedwithinthelimitsofthelimitdeviationvaluefor D 1 . 5Surface treatment Passivation(codeP)inaccordancewithISO8074orpeening(codeG)(inaccordancewithannexA). 6Designation EachforkendinaccordancewiththisInternationalStandardshallbedesignatedasshown
22、inthefollowing example. EXAMPLE 7Marking ThemarkingpositionshallbeinaccordancewithFigure1. Inadditiontothemanufacturersownmarking,eachforkendinaccordancewiththisInternationalStandardshallbe markedusingtheidentityblockspecifiedinclause6. Themarkingmethodisatthemanufacturersoption. 8Technical specific
23、ation InaccordancewithISO10955.ISO9760:2000(E) 4 AnnexA (normative) Correspondencebetweennationalstandards Thisannexestablishesacorrespondencebetweendifferentmaterialsandsurfacetreatmentstandardsfromcertain usercountries.Othermemberbodiesareinvitedtodeclaretheirmaterialsandsurfacetreatmentstandardsi
24、nthis annex. ThematerialsandprocessescitedinTables A.1andA.2areconsideredtobeequivalent,assumingthatthe requirementsforforkendsspecifiedinthisInternationalStandardarerespected. TableA.1Europeanstandards Code Material Surfacetreatment Family Standard Nature Standard No Corrosionresistantsteel EN2465
25、Passivation ISO8074 code Peening SAEAMS2431/6A TableA.2U.S.standards Code Material Surfacetreatment Family Standard Nature Standard No code Corrosionresistantsteel SAEAMS5639 or Passivation ISO8074 SAEAMS5641 Peening SAEAMS2431/6ABS ISO 9760:2000 BSI 389 Chiswick High Road London W4 4AL BSI British
26、Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of Briti
27、sh Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the
28、technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards
29、 Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply t
30、he BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI e
31、lectronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase
32、price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright,
33、in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise wit
34、hout prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.
