1、Amendement 2Scurit des machines-outils lectriquessemi-fixes Partie 2-1:Rgles particulires pour les scies circulairesAmendment 2Safety of transportable motor-operatedelectric tools Part 2-1:Particular requirements for circular sawsCommission Electrotechnique InternationaleInternational Electrotechnic
2、al CommissionPour prix, voir catalogue en vigueurFor price, see current catalogue IEC 2001 Droits de reproduction rservs Copyright - all rights reservedInternational Electrotechnical Commission 3, rue de Varemb Geneva, SwitzerlandTelefax: +41 22 919 0300 e-mail: inmailiec.ch IEC web site http:/www.i
3、ec.chCODE PRIXPRICE CODEBAmendment 2:2006 to National Standard of CanadaCAN/CSA-E1029-2-1-94Amendment 2:2001 to International Standard CEI/IEC 1029-2-1:1993 hasbeen adopted without modification (IDT) as Amendment 2:2006 toCAN/CSA-E1029-2-1-94. This Amendment was reviewed by the CSATechnical Committe
4、e on International Standards, under the jurisdiction ofthe Strategic Steering Committee on Requirements for Electrical Safety, andhas been formally approved by the Technical Committee.April 2006Modification 2:2006 la Norme nationale du CanadaCAN/CSA-E1029-2-1-94LAmendement 2:2001 la norme internatio
5、nale CEI/IEC 1029-2-1:1993 at adopt sans modifications (IDT) et constitue la Modification 2:2006 laCAN/CSA-E1029-2-1-94. Cette modification a t revue par le Comittechnique CSA sur les normes internationales, sous lautorit du Comitdirecteur stratgique sur les exigences en matire de scurit lectricit,
6、et a tapprouve par le Comit technique.Avril 2006 2 61029-2-1 amend. 2 CEI:2001AVANT-PROPOSLe prsent amendement a t tabli par le sous-comit 61F: Scurit des outils lectroportatifs moteur, du comit dtudes 61 de la CEI: Scurit des appareils lectrodomestiques etanalogues.Le texte de cet amendement est is
7、su des documents suivants:FDIS Rapport de vote61F/370/FDIS 61F/385/RVDLe rapport de vote indiqu dans le tableau ci-dessus donne toute information sur le vote ayantabouti lapprobation de cet amendement.Le comit a dcid que le contenu de la publication de base et de ses amendements ne serapas modifi av
8、ant 2006. A cette date, la publication serareconduite;supprime;remplace par une dition rvise, ouamende._Page 2020 Construction20.18 Addition:Remplacer le titre et le texte du paragraphe 20.18 existant par le nouveau paragraphesuivant:20.18 Modification:Remplacer les modalits dessai existantes par ce
9、 qui suit:La conformit est vrifie au moyen de lapplication dune sphre dun diamtre de 100 mm 1 mm linterrupteur.La mise en marche de loutil ne doit pas tre possible au moyen de la sphre._Modification 2:2006 la CAN/CSA-E1029-2-1-94 61029-2-1 Amend. 2 IEC:2001 3 FOREWORDThis amendment has been prepared
10、 by subcommittee 61F: Safety of hand-held motor-operated electric tools, of IEC technical committee 61: Safety of household and similarelectrical appliances.The text of this amendment is based on the following documents:FDIS Report on voting61F/370/FDIS 61F/385/RVDFull information on the voting for
11、the approval of this amendment can be found in the reporton voting indicated in the above table.The committee has decided that the contents of the base publication and its amendments willremain unchanged until 2006. At this date, the publication will bereconfirmed;withdrawn;replaced by a revised edi
12、tion, oramended._Page 2120 Construction20.18 Addition:Replace the title and text of the existing subclause 20.18 by the following:20.18 Modification:Replace the existing test specification by the following:Compliance is checked by applying a sphere with a diameter of 100 mm 1 mm to the switch.It shall not be possible to start the tool by means of the sphere._Amendment 2:2006 to CAN/CSA-E1029-2-1-94 ICS 25.140.20
