1、EUROPEAN CONFERENCE OF POSTAL AND TELECOMMUNICATIONS ADMINISTRATIONS Application form for testing to I-ETS 300 296 Radio Equipment and Systems (RES) Technical characteristics and test conditions for radio equipment using integral antennas intended primarily for analogue speech The submission documen
2、tation to a National Regulatory Body for Type approval purposes shall consist of two parts; Part one. Application form Part two. Test report form Version: O1 195 Adopted by ERC WG RR: February 1995 Fubkhed ii) access to the equipment modulator input; iii) access to the signal at the demodulator outp
3、ut; iv) access to the analogue output of the RF part; v) coupling arrangement (e.g. optical or acoustic coupling); vi) access to the receiver audio output. If the equipment has more than one audio output then suitable connectors for these are also required . It is not permissible to access the recei
4、ver audio output in parallel with the loudspeaker. vii) means of connecting the equipment to an external power supply. Note (f): Pre-production model For type approval to be granted on the basis of tests conducted on a pre- production model, that model must be manufactured to the same production dra
5、wings and manufacturers specification as the later production models. Where this is not the case the national regulatory authority reserves the right to require either partial or full type testing to be carried out on the final production equipment. 2 D 232b4L4 OOL50L b5 -.-“- ,-, . *-.- - -*Y- It i
6、s the applicants responsibility to obtain information on the appropriate technical parameters (channel spacing, power level, . . .) defined in each countrys national regulations before applying for type approval. It is also the applicants responsibility to ensure that the equipment meets all the reg
7、ulatory requirements for marking in the country where type approval is being sought. 3 m 2326414 0015020 307 W APPLICANTS DETAILS MANUFACTURER 0 CATEGORY OF APPLICANT (please tick rele- ia) vant box opposite If box (b), (c) OK (d) is ticked complete details in box below with respect to the manufactu
8、rer. (b) 0 IMPORTER DISTRIBUTOR 0 (C) (d) 0 AGENT ADDRESS . I . NAME FOR CONTACT PURPOSES . TELEPHONE NO: FAX NO: TELEX NO: I MANUFACTURERS DETAILS COMPANY NAME . ADDRESS NAME FOR CONTACT PURPOSES TELEPHONE NO: FAX NO: . TELEX NO: . 4 232b414 001502L 2Y3 TYPE DESIGNATION (Note 1) The type designatio
9、n may be either a single alphanumeric code 3 an alphanumeric/ code divided into two parts. Please fill in EITHER : TYPE DESIGNATION AS A SINGLE ALPHANUMERIC CODE OR : TYPE DESIGNATION IN TWO PARTS : 1. EQUIPMENT SERIES NO. ( “MODEL NUMBER“) AND 2. EQUIPMENT SPECIFIC NO. (Note 3) (“IDENTIFICATION NO“
10、) NOTES 1) This is the manufacturers numeric or alphanumeric code or name that is specific to a particular equipment. It may contain information in coded form on the characteristics of the equipment e.g. frequency, power. The manufacturer is free to choose the form of the type designation. 2) This i
11、s the number, code or trade name used by the manufacturer to describe a series or family of equipment of substantially the same mechanical and electrical construction which will include a number of related equipments. This number is often referred to as the “model no.“. 3) This is the manufacturers
12、identification number given to a specific equipment in the series or family of equipments. It is often referred to as the “identification number“. = 2326434 00350i-2 LBT = DETAILS OF -PORTABLE EQUIPMENT Category (see ETS 300 296 sub-clause 5.2.1) o Transceiver Battery charger O u CHARACTERISTICS OF
13、INTEGW ANTENNA Polarisation for the intended usage Direction of maximum power radiation Degrees TRANSMITTER TECEINICAL CHARACTERISTICS TRANSMITTER FREQUENCY Method of frequency generation 0 0 OTHER . TRANSMITTER CHANNEL SWITCHING FREQUENCY RANGE (See sub-clause 4.1.2 of the ETS) TRANSMITTER FREQUENC
14、Y ALIGNMENT RANGE (See sub-clause 4.1.2 of the ETC) 6 2326414 0015023 OLb W TRANSMITTER RF POWER CHARACTERISTICS MAXIMUM EFFECTIVE RADIATED POWER (rated as stated by the manufacturer): w AVERAGE EFFECTIVE RADIATED POWER (rated as stated by the manufacturer): w Is transmitter intended for: Yes No Yes
15、 No 0 0 0 u Continuous duty Intermittent duty If intermittent, state DUTY CYCLE Transmitter ON I . minutes Transmitter OFF I . minutes Or duty cycle expressed as a percentage . 8 Further details (if necessary) Is transmitter output power variable? o Yes 0 0 . . . . continuously variable stepped dB p
16、er step (if regular step) Number of steps maximum RF output power (Watts ) minimum RF output power (Watts) o No Maximum power . (Watts) 7 = 232b414 0015024 T52 II I TRANSMITTER - MODULATION I Others 0 Frequency I Details: . Yes No 0 0 Can the transmitter operate unmodulated ? I TRANSMITTER MODULATIO
17、N INPUT CHARACTERISTICS Modulation input signal level for 60% of maximum deviation at Hz at Microphone socket mV Impedance Ohms Accessory socket mV Impedance Ohms Other (Note 4) mV Impedance Ohms Lowest audio modulation frequency transmitted by the equipment Hz NOTE (4) For use where direct connecti
18、on is provided for test purposes. 8 232b414 0015025 999 m RECEIVER TECHNICAL CHARACTERISTICS RECEIVER - FREQUENCY METHOD OF FREQUENCY GENERATION CRYSTAL SYNTHESIZER OTHER . 0 0 0 INTERMEDIATE FREQUENCIES Ist 2nd 3rd 0 0 0 Is local oscillator injection frequency higher OK lower than the receiver nomi
19、nal frequency? Higher Lower 0 0 RECEIVER CHANNEL SWITCHING FREQUENCY RANGE (See clause 4.1.2 of Standard) . RECEIVER FREQUENCY ALIGNMENT RANGE (See clause 4.1.2 of Standard) . 9 232b434 O035026 25 RECEIVER AUDIO (AF) CHARACTERISTICS MAXIMUM RATED AUDIO (AF) FREQUENCY OUTPUT POWER INTO LOUDSPEAKER Wa
20、tts TO LINE Watts INTO EARPIECE Watts BALANCED 0 0 No 0 No YES UNBALANCED 0 Does connection carry DC voltage? 0 YES 0 No If yes, state value Normal Audio load impedance AT LOUDSPEAKER . ohms AT EARPIECE . ohms AT LINE OUTPUT . OhS At audio accessory connection or facility socket (if fitted) Output .
21、 Watts Impedance . ohms Max input level at audio accessory socket . mV Impedance . ohms 10 E 232b414 00150i-7 7bL TRANSMITTER AND RECEIVER CHARACTERISTICS ITU DESIGNATION (S) OF EMISSION . CHANNEL SEPARATION kHz State the maximum number of channels over which the equipment can operate . EXTREME TEMP
22、ERATURE RANGE over which equipment is to be type tested -2OOC to +55OC Other 0 0 Give details . CONSTRUCTION OF EQUIPMENT Single unit (Note 5) Multiple units 0 0 If multiple units describe each one clearly I NOTE 5) Unit means a physically separate item of the equipment. AUTOMATIC EQUIPMENT SWITCH O
23、FF If the equipment is designed to automatically switch off at a predetermined voltage level which is higher OK lower in value than the battery minimum voltage calculated values this shall be clearly stated. Applies . Cut-off voltage Does not apply o 0 11 2326414 0015028 6T = POWER SOURCE (S) DC Vol
24、tage (V) DC Maximum Current (A) Other 0 BATTERY . Nickel Cadmium Other Alkaline Mercury Lead acid (Vehicle Leclanch Lithium Other volts End point regulated) voltage as quoted by equipment manufacturer (Refer to sub-clauses 6.3.2 and 6.4.2 of the ETS when completing the above) SIGNALLING (see note (d
25、) Yes No 0 O Is selective signalling fitted ? Is selective signalling O 0 Analogue Digital If analogue, state format tone frequencies Hz If digital, state modulation method bit rate b/s 12 M 232b4L4 0035029 534 D ALIGNMENT RANGE The definition of the alignment range AR1 and AR2 are given in sub clau
26、ses 4.1.2 and 4.1.3 of the Standard. The applicant should ensure that the sample equipment(s) submitted are operational on the appropriate channel(s) as given in sub clauses 4.1.5 through to 4.1.11 and tick the appropriate box. OK OK OK OK OK Or 4.1.5 One sample single channel equipment of category
27、AR1 4.1.6 Three samples of single channel equipments of category AR2 4.1.7 One sample two channel equipment of category AR1 4.1.8 Three samples of two channel equipment of category AR2 4.1.9 One sample multichannel equipment of category AR1 4.1.10 Three samples of multichannel equipment of category
28、AR2 4.1.11 One sample of multichannel equipment of category AR2 where the switching range equals the alignment range If more than one option of the equipment is being submitted with different Type Designations, one or three samples, as appropriate, of each version shall be submitted . CHANNEL IDENTI
29、FICATION Each equipment, whether one or more submitted for tests shall carry clear identification (such as a serial number), together with the frequencies associated with the channel identification displayed on the equipment. 13 232b424 0025030 Z5b M OTHER ITEMS SUPPLIED Yes 0 Spare batteries Yes No
30、 0 0 Battery charging device Special tools for dismantling equipment Yes No Yes No 0 U 0 O Encoder/Decoder Test interface box (if applicable) Full documentation on equipment (Handbook and circuit diagrams) Others Yes No D U Yes No Yes No If Yes, please specify 14 DECLARATION u Yes 0 No Are the equip
31、mentc submitted representative production models? If not are the equipments pre-production models? If pre-production equipments are submitted will the final production equipm nts be identical in respects with the equipment tested If no supply full details I hereby declare that I am entitled to sign on behalf of the applioant and that the information supplied is correct and ceanplate. Signature . Name Position held . Date 15
