1、CEGS DEPARTMENT OF THE ARMY CEGS-16528 (February 1995) U.S. ARMY CORPS OF ENGINEERS Superseding CEGS-16505 (November 1991) GUIDE SPECIFICATION FOR CONSTRUCTION Includes changes through Notice 5 (August 1999) Includes note relocation Special change (August 1995) Includes Text Adjustment Change (Secti
2、on Referen-) (June 1997) Latest change indicated by CHG tags SECTION TABLE OF CONTENTS DIVISION 16 - ELECTRICAL SECTION 16528 EXTERIOR LIGHTING INCLUDING SECURITY AND CCTV APPLICATIONS 02/95 PART 1 GENERAL 1.1 REFERENCES 1.2 SYSTEM DESCRIPTION 1.2.1 Lighting System 1.2.2 Design Requirements for CCTV
3、 Assessment Lighting 1.2.3 Electrical Requirements 1.2.4 Power Line Surge Protection 1.2.5 1.2.6 1.2.7 Nameplates 1.2.8 Standard Products 1.2.9 Unusual Service Conditions 1.2.10 Hazardous Locations 1.2.11 Protection of Security Lighting System Components Interface Between CCTV Lighting and CCTV Syst
4、em Interface Between Lighting System and Power Distribution 1.2.11.1 Components and Conductors 1.2.11.2 Tamper Provisions 1.3 CORROSION PROTECTION 1.3.1 Aluminum Materials 1.3.2 Ferrous Metal Materials 1.3.2.1 Hardware 1.3.2.2 Equipment 1.3.3 Finishing 1.4 SUBMITTALS PART 2 PRODUCTS 2.1 STANDARD PRO
5、DUCT 2.2 BRACKET ARMS 2.2.1 On Aluminum, Steel, Fiberglass, and Concrete Poles SECTION 16528 Page 1 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3515789 08918Ob 7TT CEGS 2.2.2 On Wood Poles 2.2.3 Floodlight Brackets 2.3.1 Insulated Cable 2.3.2 Mes
6、senger Cable 2.3.3 Bare Copper Conductors 2.4 AERIAL CABLE HARDWARE 2.5 CABLE SPLICES AND CONNECTORS 2.6 CABLE BOXES 2.7 MANHOLES, HANDHOLES, AND PULLBOXES 2.8 CONDUIT, DUCTS AND FITTINGS 2.8.1 Conduit, Rigid Steel 2.8.2 Conduit Coatings 2.8.3 Conduit Fittings and Outlets 2.8.3.1 Boxes, Metallic Out
7、lets 2.8.3.2 Boxes, Nonmetallic, Outlet and Flush-Device Boxes and Covers 2.8.3.3 Boxes, Outlet for Use in Hazardous (Classified) Locations 2.8.3.4 Boxes, Switch (Enclosed), Surface Mounted 2.8.3.5 Fittings for Conduit and Outlet Boxes 2.8.3.6 Fittings for Use in Hazardous (Classified) Locations 2.8
8、.3.7 Fittings, PVC, for Use with Rigid PVC Conduit and Tubing 2.3 CABLE 2.8.4 Non-Metallic Duct 2.9 WOOD CROSSARMS 2.10 GROUND RODS 2.11 POLES 2.11.1 Aluminum Poles 2.11.2 Steel Poles 2.11.3 Concrete Poles 2.11.4 Wood Poles 2.11.5 Fiberglass Poles 2.11.6 Anchor Bolts 2.12 POLE LINE HARDWARE 2.13 SER
9、IES ROADWAY LIGHTING INSULATORS 2.14 ELECTRICAL ENCLOSURES 2.14.1 Interior Enclosures 2.14.2 Exposed-to-Weather Enclosures 2.14.3 Corrosion Resistant Enclosures 2.14.4 Hazardous Environment Enclosures 2.15.1 General Lighting 2.15.2 Roadway Lighting 2.16.1 High-pressure Sodium 2.16.2 Mercury Vapor 2.
10、16.3 Metal-Halide 2.17 LAMPS, INCANDESCENT 2.18 LAMPS, FLUORESCENT 2.19 LUMINAIRE COMPONENTS 2.20 LIGHTING CONTROL EQUIPMENT 2.20.1 Photo-Control Devices 2.20.2 Timer Control Switches 2.20.3 Manual Control Switches 2.20.4 Safety Switches 2.20.5 Magnetic Contactor 2.15 ILLUMINATION 2.16 LAMPS AND BAL
11、LASTS, HIGH INTENSITY DISCHARGE (HID) SOURCES 2.21 PHOTOMETRIC DISTRIBUTION CLASSIFICATION 2.22 LUMINAIRES, FLOODLIGHTING 2.22.1 HID and Incandescent 2.22.2 Fluorescent 2.23 FIXTURES SECTION 16528 Page 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-
12、,- 3535789 0893807 b3b = CEGS 2.23.1 Accessories 2.23.2 Special Fixtures 2.23.3 In-Line Fuse 2.24 SEARCHLIGHTS 2.25 FRESNEL-LENS LUMINAIRES 2.26 FLUORESCENT FLOODLIGHTS, EXTERIOR 2.27 TRANSFORMERS 2.27.1 Outdoor Dry-Type Lighting Transformers 2.27.2 Buck-Boost Transformers 2.28 WIREWAY, RAINTIGHT, S
13、UPPORT PART 3 EXECUTION 3.1 GENERAL 3.1.1 Current Site Conditions 3.1.2 Existing Equipment 3.2 ENCLOSURE PENETRATIONS 3.3 PREVENTION OF CORROSION 3.3.1 Aluminum 3.3.2 Steel Conduits 3.3.3 Cold Galvanizing 3.4 CABLE INSTALLATION 3.4.1 Splices 3.4.2 Installation in Duct Lines 3.4.3 Direct Burial 3.4.3
14、.1 Trenching 3.4.3.2 Requirements for Installation in Duct 3.4.3.3 Location of Cable Splices 3.4.3.4 Markers 3.4.3.5 Warning Tape 3.4.4.1 Installation 3.4.4.2 Grounding and Bonding Connections 3.4.4.3 Grounding Conductors and Electrodes 3.4.4.4 Ground Resistance Testing 3.4.4 Messenger Cable 3.5 AER
15、IAL CABLE SPLICES 3.6 LASHING WIRE 3.7 STRESS LOOPS 3.8 CONNECTIONS TO BUILDINGS 3.9 DUCT LINES 3.9.1 Requirements 3.9.2 Treatment 3.9.3 Concrete Encasement 3.9.4 Nonencased Direct-Burial 3.9.5 Installation of Couplings 3.9.5.1 Plastic Duct 3.9.6 Concrete 3.9.7 Duct Line Markers 3.10.1 Construction
16、3.10.2 Appurtenances 3.10.3 Cable Pulling-In Irons 3.10.4 Ground Rods 3.11 POLE INSTALLATION 3.11.1 Pole Brackets 3.11.2 Concrete Foundations 3.11.3 Rigid Steel Conduit Ells 3.11.4 Wood Pole Installation 3.11.5 Aluminum, Steel, Fiberglass and Concrete Pole Installation 3.10 HANDHOLES SECTION 16528 P
17、age 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-= 3515789 0891808 572 CEGS 3.11.5.1 Cast-In-Place Foundations 3.11.5.2 Power-Installed Screw Foundations 3.12 LIGHTING 3.12.1 Lamps 3.12.2 Fixture Installation 3.12.2.1 Accessories 3.12.2.2 In-lin
18、e Fuses 3.12.2.3 Special Fixtures 3.13 TRANSFORMER INSTALLATION 3.14 LIGHTING CONTROL SYSTEM 3.14.1 Photo-Control 3.14.2 Time Control Switches 3.14.3 Manual and Safety Switches 3.14.4 Magnetic Contactors 3.14.5 CCTV Alarm Interface 3.15.1 Ground Rods and Pole Butt Electrodes 3.15.2 Items to be Groun
19、ded 3.15.3 Lighting Pole 3.15.4 Handhole 3.15.5 Metal Cable Boxes 3.16.1 Testing For CCTV Assessment Lighting 3.16.2 Operating Test 3.16.3 Ground Resistance Measurements 3.15 GROUNDING 3.16 TESTS - End of Section Table of Contents - SECTION 16528 Page 4 Provided by IHSNot for ResaleNo reproduction o
20、r networking permitted without license from IHS-,-,- m 3535789 0893809 409 m CEGS DEPARTMENT OF THE ARMY CEGS-16528 (February 1995) U.S. ARMY CORPS OF ENGINEERS Superseding CEGS-16505 (November 1991) GUIDE SPECIFICATION FOR CONSTRUCTION Includes changes through Notice 5 (August 1999) Includes note r
21、elocation Special change (August 1995) Includes Text Adjustment Change (Section Reference)(Sune 1997) Latest change indicated by CHG tags SECTION 16528 EXTERIOR LIGHTING INCLUDING SECURITY AND CCTV APPLICATIONS 02/95 NOTE: This guide specification covers the requirements for lighting for roads, walk
22、s, security, and closed circuit television (CCTV) assessment. This guide specification is to be used in the preparation of project specifications in accordance with ER 1110-1-8155. Comments and suggestions on this guide specification are welcome and should be directed to the proponent of the specifi
23、cation. A listing of proponents, including their organization designation and telephone number, is at URL http:/worw.hnd.usace.army.mil/techinfo/index.htm, and an electronic feedback page for submission of recommended changes is available at the same address. Use of electronic communication is encou
24、raged. PART 1 GENERAL NOTE: This specification does not include provision for high-mast roadway and parking lot lighting (poles over 18.3 meters (60 feet). Requirements for materials and procedures for special or unusual design will be added as necessary for specific projects. conform to TM 5-811-1/
25、AFJMAN 32-1080. Standard details will conform to the general requirements of TM 5-811-1/AFJM?W 32-1080, and may be modified to Quantity and quality of illumination will SECTION 16528 Page 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3515789 O891
26、810 I120 CEGS suit project conditions. Incandescent lamps, Fluorescent lamps, and Mercury Vapor Lamps shall not be used for CCTV. In addition, tungsten lamps other than infrared lamps shall not be used for CCTV. Two types of infrared luminaires are currently available. Fixtures with special lamps ut
27、ilizing optical dichroic mirror coatings that produce only infrared light and fixtures that use conventional lamps that pass the light output through infrared filters. Special lamps have the advantage of operating cooler and not requiring a cooling fan, thus operating quieter and requiring less main
28、tenance. The major disadvantages are high lamp replacement cost due to short bulb life (2000 to 4000 hours) and special lamp design. The 2000 hour lamps produce more infrared light energy and are preferred over the 4000 hour lamps. Another disadvantage is the limited variety of wattages available, b
29、ut this is normally resolved by fixture placement during site lighting system design. Conventional lamps utilizing special power supplies and infrared falters have the advantages of low bulb replacement cost and bulb life ranging from 1700 to 18000 hours. (Note: Special power supplies reduce current
30、 flow to the bulb and allow it to operate at a lower filament temperature to shift light output more into the near infrared (NIR) light spectrum and requires less filtering. This has the additional advantage of extending bulb life.) bulb sizes are available and no special bulbs are required. convent
31、ional bulb is the heat generated utilizing an infrared filter which must be cooled by a cooling fan. Fans require maintenance and the loss of the fan will destroy the filter. Filters are expensive. A variety of The main disadvantage of using a 1.1 REFERENCES NOTE: Issue (date) of references included
32、 in project specifications need not be more current than provided by the latest change (Notice) to this guide specification. The publications listed below form a part of this specification to the extent referenced. The publications are referred to in the text by basic designation only. AMERICAN ASSO
33、CIATION OF STATE HIGHWAY AND TRANSPORTATION OFFICIALS (AASHTO) SECTION 16528 Page 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3535787 0893813 Ob7 M CEGS AASHTO LTS-3 (1994) Standard Specifications for Structural Supports for Highway Signs, Lumi
34、naires and Traffic Signals AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI C78.1 (1991; C78.la; R 1996) Fluorescent Lamps - Rapid-Start Types - Dimensional and Electrical Characteristics (1992) Specifications forMercury Lamps ANSI C78.40 ANSI C78.1350 (1990) Electric Lamps - 400-Watt, 100-Volt, S5
35、1 Single-Ended High-pressure Sodium Lamps ANSI C78.1351 ANSI C78.1352 (1989) Electric Lamps - 250-Watt, 100-Volt 550 Single-Ended High-pressure Sodium Lamps (1990) Electric Lamps - 1000-Watt, 250-Volt, 552 Single-Ended High-pressure Sodium Lamps (1989) Electric Lamps - 150-Watt, 55-Volt 555 High-pre
36、ssure Sodium Lamps ANSI C78.1355 ANSI C78.1375 (1996) 400-Watt, M59 Single-Ended Metal-Halide Lamps ANSI C78.1376 ANSI C80.1 ANSI C82.4 (1996) lOOO-Watt, M47 Metal-Halide Lamps (1995) Rigid Steel Conduit - Zinc Coated (1992) Ballasts for High-Intensity-Discharge and Low-Pressure Sodium Lamps (Multip
37、le-Supply Type) (1986; R 1997) Sealed Insulated Underground Connector Systems Rated 600 Volts ANSI C119.1 ANSI C135.1 ANSI C135.14 ANSI C135.30 ANSI C136.2 ANSI C136.3 ANSI C136.6 (1979) Galvanized Steel Bolts and Nuts for Overhead Line Construction (1979) Staples with Rolled or Slash Points for Ove
38、rhead Line Construction (1988) Zinc-Coated Ferrous Ground Rods for Overhead or Underground Line Construction (1996) Luminaires, Voltage Classification Roadway Lighting Equipment (1995) Roadway Lighting Equipment-Luminaire Attachments (1997) Roadway Lighting Equipment - Metal Heads and Reflector Asse
39、mblies - SECTION 16528 Page 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-m 3515789 0891812 TT3 CEGS ANSI C136.9 ANSI C136.10 ANSI C136.11 ANSI C136.15 ANSI C136.20 ANSI 05.1 Mechanical and Optical Interchangeability (1990) Roadway Lighting - Soc
40、ket Support Assemblies for Use in Metal Heads - Mechanical Interchangeability (1996) Roadway Lighting- Locking-Type Photocontrol Devices and Mating Receptacles - Physical and Electrical Interchangeability and Testing (1995) Multiple Sockets for Roadway Lighting Equipment (1986) Roadway Lighting, Hig
41、h-Intensity-Discharge and Low-Pressure Sodium Lamps in Luminaires - (1990) Roadway Lighting Equipment - Fiber Reinforced Plastic (FRP) Fiber Lighting Poles (1992) Specifications and Dimensions for Wood Poles AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM A 36/A 36M (1997a) Carbon Structural
42、Steel ASTM A 48 (1994a) Gray Iron Castings ASTM A 123/A 123M ASTM A 153/A 153M ASTM A 575 ASTM A 576 (1997a) Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products (1998) Zinc Coating (Hot-Dip) on Iron and Steel Hardware (1996) Steel Bars, Carbon, Merchant Quality, M-Grades (1990b; R 1995) St
43、eel Bars, Carbon, Hot-Wrought, Special Quality ASTM B 2 (1994) Medium-Hard-Drawn Copper Wire ASTM B 8 (1995) Concentric-Lay-Stranded Copper Conductors, Hard, Medium-Hard, or Soft ASTM B 117 (1997) Operating Salt Spray (Fog) Apparatus ASTM C 478 ASTM D 1654 (1997) Precast Reinforced Concrete Manhole
44、Sect ions (1992) Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments AMERICAN WOOD-PRESERVERS ASSOCIATION (AWPA) SECTION 16528 Page 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3535789 0893813 93T = CEGS AWPA C4 AWPA C2
45、5 AWPA Pl/P13 AWPA P8 AWPA P9 (1995) Poles - Preservative Treatment by Pressure Processes (1995) Sawn Crossarms - Preservative Treatment by Pressure Processes (1995) Standard for Coal Tar Creosote for Land and Fresh Water and Marine (Coastal Water Use) (1997) Standards for Oil-Borne Preservatives (1
46、997) Standards for Solvents for Organic Preservative Systems ELECTRONIC INDUSTRIES ASSOCIATION (EIA) EIA ANSI/EIA/TIA 232-F (1997) Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binar Interchange ILLUMINATING ENGINEERING SOCIETY OF NORTH AMERICA (IE
47、SNA IESNA RP-8 (1983; R 1993) Roadway Lighting INSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS (IEEE) 7 Data IEEE C2 (1997) National Electrical Safety Code IEEE C62.41 IEEE C136.13 IEEE Std 81 NEMA 250 (1991; R 1995) Surge Voltages in Low-Voltage AC Power Circuits (1987; R 1997) Metal Brackets for
48、 Wood Poles (1983) Guide for Measuring Earth Resistivity, Ground Impedance, and Earth Surface Potentials of a Ground System (Part i) NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA) (1991) Enclosures for Electrical Equipment (1000 Volts Maximum) NEMA ICs 1 (1993) Industrial Control and Systems N
49、EMA ICs 2 NEMA ICs 6 NEMA OS 1 (1993) Industrial Control and Systems Controllers, Contactors, and Overload Relays Rated Not More Than 2,000 Volts AC or 750 Volts DC Assemblies (1993) Industrial Control and Systems, Enclosures (1996) Sheet-Steel Outlet Boxes, Device Boxes, Covers, and Box Supports SECTION 16528 Page 9 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
